Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment.
Recommended Use :-
It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion.
Physical Data
COLOUR : Red
FINISH : Matt
SOLIDS BY VOLUME : 40 �± 3%
THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ
FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C
DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE : BASE : 6months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendation)
APPLICATION : By Brush / By Conventional Spray
THINNER : Type 290
POT LIFE : 3 hours min at 30�° C
RECOMMENDED DFT : 30-40 �µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320)
COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
shell and foreign material (by weight) 0.05% maximum
meal or dust (by weight) 1% maximum thru 3/32"
color fairly uniform in color, notdarker than "amber" skin color
color classication fancy mostly golden color or lighter, max 3% by weight darker than light
total defects (by weight) 3% maximum, due to o-sizing
moisture 2 % maximum
size min / max diameter
fancy x-large 8/16" not a complete half
fancy large 7/16" 8/16"
fancy medium 4/16" 7/16"
fancy small 3/16" /4/16"
fancy midget 1/16" 3/16
Nutrient ingredients: Protein, Carotene, Crude fiber, Calcium, Phosphorus, Iron and Vitamin C, B1, B2, E.
Character: Easy open, Crisp kernel, pure natural processed, green & healthy, good taste.
Functions: Prevent cell aging; Lower cholesterol; Improve memory, aging and moisturize the skin; Anti-cancer; Bacteriostatic antiphlogistic.
shell and foreign material (by weight) 0.05% maximum
meal or dust (by weight) 1% maximum thru 3/32"
color fairly uniform in color, notdarker than "amber" skin color
color classication fancy mostly golden color or lighter, max 3% by weight darker than light
total defects (by weight) 3% maximum, due to o-sizing
moisture 2 % maximum
size min / max diameter
fancy x-large 8/16" not a complete half
fancy large 7/16" 8/16"
fancy medium 4/16" 7/16"
fancy small 3/16" /4/16"
fancy midget 1/16" 3/16
Nutrient ingredients: Protein, Carotene, Crude fiber, Calcium, Phosphorus, Iron and Vitamin C, B1, B2, E.
Character: Easy open, Crisp kernel, pure natural processed, green & healthy, good taste.
Functions: Prevent cell aging; Lower cholesterol; Improve memory, aging and moisturize the skin; Anti-cancer; Bacteriostatic antiphlogistic.
Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment.
Recommended Use :-
It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion.
Physical Data :-
COLOUR : Red
FINISH : Matt
SOLIDS BY VOLUME : 40 �± 3%
THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ
FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C
DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE : BASE : 6months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendation)
APPLICATION : By Brush / By Conventional Spray
THINNER : Type 290
POT LIFE : 3 hours min at 30�° C
RECOMMENDED DFT : 30-40 �µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320)
COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment.
Recommended Use :-
It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion.
Physical Data :-
COLOUR :- Yellow
FINISH :- Matt
SOLIDS BY VOLUME :- 40 �± 3%
THEORETICAL SPREADING RATE :- 13.33 sq.mt / lit at recommended DFT of 30 �µ
FLASH POINT :- Base : Above 23�° C Hardener : Above 30�° C
DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) :- SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE :- BASE : 6months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation.
Application Data
MIXING RATIO :- Base : Hardener (As per our recommendation)
APPLICATION :- By Brush / By Conventional Spray
THINNER :- Type 290
POT LIFE :- 3 hours min at 30�° C
RECOMMENDED DFT :- 30-40 �µ.
OVERCOATING INTERVAL :- MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320)
COMPATIBILITY :- Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Application Method
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Strain the paint through Nylon filter cloth of 200 mesh size and apply uniformly over the surface. All equipments used for above should be properly clean.
Application :- By Brush / By Conventional Spray / By Airless Spray
Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner and ensuring the uniform application. Use quality brushes for paint application.
For Conventional Spray application :-
Thinner : Type 290
Addition : 10-15%
Nozzle Orifice : 1.2 -1.4 mm
Nozzle Pressure : 40-70 p.s.i.
For Airless Spray application :-
Thinner : Type 290
Addition : Max 5%
Nozzle Orifice : 0.28- 0.37 mm
Nozzle Pressure : 1400-1800 p.s.i.
1746 Pu R O Z C Anti Corrosive Primer Suppliers
Short on time? Let Pu R O Z C Anti Corrosive Primer sellers contact you.
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube
OD 20~405mm in theory
Thickness 1.2~15.7mm
Length Any Length Below 16 Meter
Standard GB,ASTM,BS,EN,JIS
Material Chinese Grade, Q195, Q215 Q235, Q345
ASTM, Grade B,Grade C,Grade D,Grade 50
EN, S185,S235JR,S235JO,E335,S355JR,S355J2
JIS, SS330,SS400,SPFC590
Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery
Ends
Plain, Beveled, Thread With Couplings Or Sockets;
Plastic Caps And Steel Rings Can Be Provided If Possible
Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment
Technique Hot Rolled Or Cold Rolled ERW
Package Covered With Tarpaulin, Containers Or In Bulk
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube
OD 20~405mm in theory
Thickness 1.2~15.7mm
Length Any Length Below 16 Meter
Standard GB,ASTM,BS,EN,JIS
Material Chinese Grade, Q195, Q215 Q235, Q345
ASTM, Grade B,Grade C,Grade D,Grade 50
EN, S185,S235JR,S235JO,E335,S355JR,S355J2
JIS, SS330,SS400,SPFC590
Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery
Ends
Plain, Beveled, Thread With Couplings Or Sockets;
Plastic Caps And Steel Rings Can Be Provided If Possible
Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment
Technique Hot Rolled Or Cold Rolled ERW
Package Covered With Tarpaulin, Containers Or In Bulk
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube
OD 20~405mm in theory
Thickness 1.2~15.7mm
Length Any Length Below 16 Meter
Standard GB,ASTM,BS,EN,JIS
Material Chinese Grade, Q195, Q215 Q235, Q345
ASTM, Grade B,Grade C,Grade D,Grade 50
EN, S185,S235JR,S235JO,E335,S355JR,S355J2
JIS, SS330,SS400,SPFC590
Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery
Ends
Plain, Beveled, Thread With Couplings Or Sockets;
Plastic Caps And Steel Rings Can Be Provided If Possible
Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment
Technique Hot Rolled Or Cold Rolled ERW
Package Covered With Tarpaulin, Containers Or In Bulk
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube
OD 20~405mm in theory
Thickness 1.2~15.7mm
Length Any Length Below 16 Meter
Standard GB,ASTM,BS,EN,JIS
Material Chinese Grade, Q195, Q215 Q235, Q345
ASTM, Grade B,Grade C,Grade D,Grade 50
EN, S185,S235JR,S235JO,E335,S355JR,S355J2
JIS, SS330,SS400,SPFC590
Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery
Ends
Plain, Beveled, Thread With Couplings Or Sockets;
Plastic Caps And Steel Rings Can Be Provided If Possible
Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment
Technique Hot Rolled Or Cold Rolled ERW
Package Covered With Tarpaulin, Containers Or In Bulk
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube
OD 20~405mm in theory
Thickness 1.2~15.7mm
Length Any Length Below 16 Meter
Standard GB,ASTM,BS,EN,JIS
Material Chinese Grade, Q195, Q215 Q235, Q345
ASTM, Grade B,Grade C,Grade D,Grade 50
EN, S185,S235JR,S235JO,E335,S355JR,S355J2
JIS, SS330,SS400,SPFC590
Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery
Ends
Plain, Beveled, Thread With Couplings Or Sockets;
Plastic Caps And Steel Rings Can Be Provided If Possible
Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment
Technique Hot Rolled Or Cold Rolled ERW
Package Covered With Tarpaulin, Containers Or In Bulk
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube
OD 20~405mm in theory
Thickness 1.2~15.7mm
Length Any Length Below 16 Meter
Standard GB,ASTM,BS,EN,JIS
Material Chinese Grade, Q195, Q215 Q235, Q345
ASTM, Grade B,Grade C,Grade D,Grade 50
EN, S185,S235JR,S235JO,E335,S355JR,S355J2
JIS, SS330,SS400,SPFC590
Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery
Ends
Plain, Beveled, Thread With Couplings Or Sockets;
Plastic Caps And Steel Rings Can Be Provided If Possible
Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment
Technique Hot Rolled Or Cold Rolled ERW
Package Covered With Tarpaulin, Containers Or In Bulk
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube
OD 20~405mm in theory
Thickness 1.2~15.7mm
Length Any Length Below 16 Meter
Standard GB,ASTM,BS,EN,JIS
Material Chinese Grade, Q195, Q215 Q235, Q345
ASTM, Grade B,Grade C,Grade D,Grade 50
EN, S185,S235JR,S235JO,E335,S355JR,S355J2
JIS, SS330,SS400,SPFC590
Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery
Ends
Plain, Beveled, Thread With Couplings Or Sockets;
Plastic Caps And Steel Rings Can Be Provided If Possible
Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment
Technique Hot Rolled Or Cold Rolled ERW
Package Covered With Tarpaulin, Containers Or In Bulk
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube
OD 20~405mm in theory
Thickness 1.2~15.7mm
Length Any Length Below 16 Meter
Standard GB,ASTM,BS,EN,JIS
Material Chinese Grade, Q195, Q215 Q235, Q345
ASTM, Grade B,Grade C,Grade D,Grade 50
EN, S185,S235JR,S235JO,E335,S355JR,S355J2
JIS, SS330,SS400,SPFC590
Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery
Ends
Plain, Beveled, Thread With Couplings Or Sockets;
Plastic Caps And Steel Rings Can Be Provided If Possible
Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment
Technique Hot Rolled Or Cold Rolled ERW
Package Covered With Tarpaulin, Containers Or In Bulk
Item Hot Dipped Galvanized Round Steel Pipe/GI Pipe/Galvanised Tube
OD 20~405mm in theory
Thickness 1.2~15.7mm
Length Any Length Below 16 Meter
Standard GB,ASTM,BS,EN,JIS
Material Chinese Grade, Q195, Q215 Q235, Q345
ASTM, Grade B,Grade C,Grade D,Grade 50
EN, S185,S235JR,S235JO,E335,S355JR,S355J2
JIS, SS330,SS400,SPFC590
Application Used For Water, Gas, Stream, Combustible Fluids And Other Liquid Delivery
Ends
Plain, Beveled, Thread With Couplings Or Sockets;
Plastic Caps And Steel Rings Can Be Provided If Possible
Surface Bared, Galvanized, Oiled, Color Paint, 3PE; Or Other Anti-corrosive Treatment
Technique Hot Rolled Or Cold Rolled ERW
Package Covered With Tarpaulin, Containers Or In Bulk
We are sellers of certified halal frozen whole chicken, chicken feet, chicken , beef, pork
our products meet the SGS testing, we can supply all kinds of frozen chicken cuts. Freezing Process: IQF Part: Whole Shape:
Packaging: Cartons
Shelf Life: 12 months
We
supply high quality and large quantities of Halal and non-halal frozen
whole chicken, frozen chicken feet and frozen chicken parts.
The different types of frozen whole chicken and frozen chicken parts that we supply are:
A. Whole chicken. Please indicate the size that you want.
B. Chicken leg quarter/Chicken whole leg
C. Chicken drum stick
D. Chicken thigh
E. Chicken boneless leg
F. Chicken
G. Chicken wing tips
H. Chicken 2 joint wing
I. Chicken whole leg boneless with skin on
J. Chicken feet
K. Chicken gizzards
L. Chicken wing middle joint
M. Chicken inner fillet middle half cut
N. Chicken boneless and skinless breast without inner fillet
O. Chicken half breast boneless and skinless without inner fillet
Q. Chicken head
R. Chicken back
S. Chicken front
T. MDM
Specifications:
- Feather off
- well cleaned and fresh
- no bruises
- no black pads or ammonia burns
- no bad smells
- no excessive blood or blood stains
- moisture content is less than 3%
weight and packaging:
whole chicken each weight 800g to 2500g x 7-10 in a box
Other parts from 2kg up to 10 - 15/20kg
An easy-to-use, water-based primer specifically formulated to �¢??lock-out�¢?? corrosion on a wide range of metals. Applied correctly, is guaranteed for years.
USES
Suitable on sheet metal, castings, wrought iron, TNT Bar, steel Bar and steelwork. This product is not recommended for automotive use.
COLOURS
Available in natural green.
SIZES
Available in 4 litre,10 litre and 20 litre
COVERAGE
Up to 14 square metres per litre depending upon surface porosity and application method.
APPLICATION
Roller, brush, dip or airless spray. Provide adequate ventilation during use.
DRYING TIMES
Touch Dry Time - 20 minutes. Recoat Dry Time - 2 hours. Drying times refer to normal conditions (30�?�°C, 50% humidity). Under cooler, humid or still conditions, longer drying times may be necessary. DO NOT USE IN TEMPERATURES BELOW 10'c OR ABOVE 45C.
DANGEROUS GOODS CLASSIFICATION
Not classified as Dangerous Goods.
SURFACE PREPERATION
Previously Painted Surfaces :
Scrape off loose and flaking paint and make sure the remainder is firmly attached. Sand glossy surfaces and enamels thoroughly and wipe clean. Remove all rust by abrasive blasting or mechanical sanding. Treat any remaining rust. Prime treated and bare areas with one coat SAFFRO Anti-Corrosive Metal Primer. In highly corrosive environments or within 2 kilometre of the sea, apply 2 coats of SAFFRO Anti- Corrosive Metal Primer.
TNT BAR,STEEL BAR AND IRON:
Remove all grease, dirt and other surface contaminants.Remove all rust by abrasive blasting or mechanical sanding. Treat any remaining rust with. Prime treated and bare areas with one coat SAFFRO Anti-Corrosive Metal Primer. In highly corrosive environments or within 2 kilometre of the sea, apply 2 coats of SAFFRO Anti- Corrosive Metal Primer
INTRODUCTION
The product is a high molecular 30 TBN Calcium Sulphonate. The increased oil solubility of the organic portion of this Sulphonate enables the product to provide rust protection and acts as a dispersant for graphite and molybdenum disulfide. It can be used as an additive in lubricating oils, greases, rust inhibition, antiwear and hydraulic fluids.
SPECIFICATION
Test Method Minimum Maximum
Appearance Visual Brown liquid Brown liquid
Colour ASTM D 1500 2 5
Sp. Gravity @ 15.6 C ASTM D 1298 0.95 1.05
Flash Point C (COC) ASTM D 92 175 -
Viscosity @ 100 C, cst ASTM D 445 40 70
Avg. Molecular wt. ASTM D 3712 1000 1100
TBN (mg KOH/gm) ASTM D 974 28 35
Calcium Content %[w/w] GL EDTA 1A 2.8 3.0
FORMULATION
The product is recommended for use at 0.5% to10.0%wt. In suitable base stocks to provide
detergency & anti-rust performance characteristics to oils. It is compatible with mineral base oils, white oils, and synthetic base stocks.
APPLICATION
Imparts excellent rust prevention, detergency and Anti oxidant Properties.
Corrosion inhibitor in mill oils, short-term rust preventatives, coatings and greases.
Dispersant and corrosion inhibitor in engine oil.
Provides excellent resistance to coated Cold Rolled Steel for antirust applications.
Works in extremely hostile conditions like highly acidic environment as well as highly humid atmosphere.
It is non-staining having detergent, dispersant properties.
Environmental Friendly, Biodegradable without side effect.
HANDLING AND STORAGE
Calcium Sulphonate is normally handled at room temperature. For general purposes, the following storage and handling temperatures are recommended: Storage Handling 50-70C
(122-158F).
For more extensive information on the safe handling and use of this product, see the Material
Safety Data
Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment.
Recommended Use :-
It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion.
Physical Data
COLOUR : Grey
FINISH : Matt
SOLIDS BY VOLUME : 40 �± 3%
THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ
FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C
DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE : BASE : 6months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation.
Application Data
MIXING RATIO : Base : Hardener (As per our recommendation)
APPLICATION : By Brush / By Conventional Spray
THINNER : Thinner 290
POT LIFE : 3 hours min at 30�° C
RECOMMENDED DFT : 30-40 �µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320)
COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Safety Features
Abrasion Resistant
Anti Skid
Light Weight
Oil Resistant
Overview
Product Name : Volkan Shoe
Sizes : 5 - 11
STANDARD FEATURES
Abrasion Resistant
Anti Skid
Anti Static
Cushionong Effect
DIP PU Construction
High Flexing
Light Weight
Odour Free
Oil and Acid Resistant
Sweat Absorption
Optional Features
High Voltage Insulation
Boot Care
* Clean your footwear regularly using high quality products that are suitable for the cleaning purpose. NEVER use caustic or corrosive cleaning agents.
* When footwear is not in use clean the sole and store in a well-ventilated area. Never store the footwear underneath heavy items or in contact with sharp objects. If the footwear is wet allow it to dry slowly and naturally away from direct heat sources before storage.
* To put on and take off footwear always fully undo fastening systems. Use a shoe horn to wear shoes. Only wear footwear of a suitable size. Products which are either too loose or too tight will restrict movement and will not provide optimum levels of protection and comfort.
* The shoe should be used for the purpose for which it has been designed.
Some facts about feet-
* Most of the muscles are in your feet. Thus you should wear comfortable shoes.
* The body temperature is regulated through your feet
* Maximum number of nerves go through your feet.
100% Comfort Guaranteed
* Quality leather upper and high quality breathable lining materials are used for proper air circulation in shoe for keeping the feet cool and odour free.
* Construction of lasts based on extensive survey enabling the lasts/shoes to be manufactured for better fit providing maximum comfort.
* Wider Steel and Ultra light Weight Composite Toe caps which provides more room for finger movements enhancing comfort.
* Cushioned Insoles providing better comfort.
* Shock absorbing PU midsole with low density providing uniform cushioning and comfort.
* Light Weight PU for a featherlite feel even during high stress working conditions.
SAFETY FEATURES
Abrasion Resistant
Acid Resistant
Anti Static Insole
Excellent Shock Absorber
Fine Leather
Light Weight
Oil Resistant
Slip Resistant Sole
Steel toe / Kavlar
Steel Toe Cap
ADDITIONAL PRODUCT INFO
OVERVIEW
Product Name : Gents Safety Boots
Standard : S3
Sizes : 36 - 47 (5-13)
Colors : Brown/black
AVAILABLE OPTIONS
Product Number : 3002-02 PU/Rubber
Standard : S1,s1p,s2,s3
Toe: Fibre Glass/steel
Midsole: Steel/kevlar
Sole : DD PU/Rubber
Color: Brown & Black
MATERIALS
Upper: Water Resistant Buff Printed Leather
Lining: Camberella - 100% Camberella Polymide,breathable,absorbing And Relaxing Moisture
Toe : Fibre Glass
Midsole : Kevlar
Footbed / Socks: Moulded Antistatic
Sole : 3002- PU Rubber
Certified : EN ISO 20345:2011 SRA
BOOT CARE
* Clean your footwear regularly using high quality products that are suitable for the cleaning purpose. NEVER use caustic or corrosive cleaning agents.
* When footwear is not in use clean the sole and store in a well-ventilated area. Never store the footwear underneath heavy items or in contact with sharp objects. If the footwear is wet allow it to dry slowly and naturally away from direct heat sources before storage.
* To put on and take off footwear always fully undo fastening systems. Use a shoe horn to wear shoes. Only wear footwear of a suitable size. Products which are either too loose or too tight will restrict movement and will not provide optimum levels of protection and comfort.
* The shoe should be used for the purpose for which it has been designed.
Some facts about feet-
* Most of the muscles are in your feet. Thus you should wear comfortable shoes.
* The body temperature is regulated through your feet
* Maximum number of nerves go through your feet.
100% COMFORT GUARANTEED
* Quality leather upper and high quality breathable lining materials are used for proper air circulation in shoe for keeping the feet cool and odour free.
* Construction of lasts based on extensive survey enabling the lasts/shoes to be manufactured for better fit providing maximum comfort.
* Wider Steel and Ultra light Weight Composite Toe caps which provides more room for finger movements enhancing comfort.
* Cushioned Insoles providing better comfort.
* Shock absorbing PU midsole with low density providing uniform cushioning and comfort.
* Light Weight PU for a featherlite feel even during high stress working conditions.
1746 Pu R O Z C Anti Corrosive Primer Suppliers
Short on time? Let Pu R O Z C Anti Corrosive Primer sellers contact you.
