Find Verified Cement Bricks Suppliers, Manufacturers and Wholesalers

Cement

Product Code Product Description

PRS-CM00020 High Pressure Cement Autoclave, 230 V 50-60 Hz

STANDARDS : ASTM C151, C490; UNE 7207

The PRS-CM00020 High Pressure Cement Autoclave is designed to perform expansion tests on cement specimens.10 specimens can simultaneously be tested in the high pressure steam vessel of 154 mm diameter and 430 mm height.

The Autoclave consists of a pressure gauge, pressure regulator, temperature regülatör, control switches and safety valve.

PRS-CM0033 Two Gang Shrinkage mould should be ordered separately.

The High Pressure Cement Autoclave is supplied complete with;
â?¢ Specimen Rack, 10 samples capacity

Dimensions 450x475x1080 mm
Weight (approx.) 55 kg
Power 2600 W

Pull-off tester 20 kn
En 1015/12 - 1348 - 1542 - 12504/3 • astm c 90
With servo-controlled drive unit and tensiontransducer,
Fully integrated.


11

Product Code Product Description

PRS-CM6700 250 kN Cement Compression Frame

PRS-CM6710 15/250 kN Cement Flexure/Compression Frame

STANDARDS : EN 196-1, 459-2, 1015-11, 13454-2; ASTM C109, C348, C349;BS 3892-1, 4551-1

The PRS-CM6700 and PRS-CM6710 , very rigid two column frames have been designed for compression and/or flexure testing of mortar prisms and cubes specimens. Load cells are used on both frames to provide high accuracy in load measuring. Both frames are fitted with round platens with 165 mm diameter and these should be used together with suitable flexure and compression devices.

Distance pieces and transparent front-rear safety doors (should be factory insttalled ) should be ordered separately.


Distance Pieces for Frame

Due to the modular design of the frames any sample with suitable size, load and pace rate can be test on both chambers by decreasing the distance between platens.
Distance Pieces

PRS-CM4630 Distance piece dia. 165 mm x 15 mm
PRS-CM4631 Distance piece dia. 165 mm x 30 mm
PRS-CM4633 Distance piece dia. 165 mm x 50 mm
PRS-CM4634 Distance piece dia. 165 mm x 90 mm

Platens

PRS-CM0116 Upper Loading Platen with Ball Seating Assembly Ã?:165 mm and Lower Loading Platen, Ã?:165 mm

Manufactured from high quality steel are hardened (more than HRC 53), smoothed and finished.

The roughness value for the surface texture of machine and auxiliary platens are 3.2 μm.

Loading Cylinder Assembly & Limit Switch

All frames have a single acting up stroking ram. The diameter of piston changes with regard to the capacity.
The maximum ram stroke is 50 mm, a limit switch is fitted to prevent over travel of the ram which cuts the power to the pump.
There is a low friction coaxial PTFE seal between the cylinder and the piston fitted to the cylinder.

Accessories

PRS-CM0120/A Flexure Jig Assembly to test 40x40x160 mm mortar prisms, ASTM

PRS-CM0120/E Flexure Jig Assembly to test 40x40x160 mm mortar prisms, EN

PRS-CM0121/A Compression Jig Assembly to test 50 mm (2â?�) mortar cubes, ASTM

PRS-CM0121/E Compression Jig Assembly to test portions of 40x40x160 mm mortar prisms, EN

Product Code Product Description

PRS-CM0037 Digital Length Comparator

PRS-CM0038 Length Comparator with Length Measuring Sensor and Digital Readout Unit

STANDARDS : EN 1367â??4, 12617â??4, 12808-4; ASTM C151, C157, C227, C311, C341, C342, C441,C452, C490, C531, C596, C806, C878; BS 1881:5, 6073

Length Comparators are used to determine the length changes on different type of cement prisms.

The set consists of a length measuring frame with measuring device attached to it.

There are 2 models available; PRS-CM0037 is with 0.001 mm x 12,7 mm digital dial gauge (PRS-CM0152) and PRS-CM0038 is with special 0.0001 mm x 30 mm transducer and readout unit.

Reference rod and moulds should be ordered separately according to test to perform.

Product Code Dimensions Weight

PRS-CM0037 180x180x450 mm 6 kg

PRS-CM0038 250x250x650 mm 8 kg

Product Code Product Description

PRS-CM0029 Three Gang Shrinkage Mould 40x40x160 mm, EN

PRS-CM0030 Steel Insert 40x40x160 mm for PRS-CM0029, 18 pieces/pack

PRS-CM0031 Reference Rod 160 mm Long with Convex Hemispherical End

PRS-CM0032 Tamper, Hardwood 38x15x200mm, 250 g, EN

PRS-CM0033 Two Gang Shrinkage Mould 25x25x285 mm, ASTM

PRS-CM0034 Steel Insert 25x25x285 mm for PRS-CM0033, 12 pieces/pack

PRS-CM0035 Reference Rod 295 mm Long with Convex Hemispherical End

STANDARDS : ASTM C151, C157, C452, C490, C596; EN 12617-4

The PRS-CM0029 , PRS-CM0033 Three and Two Gang Shrinkage Moulds are used for the determination of linear shrinkage/expansion of cement mortar when used together with the PARSROS Length Comparator (PRS-CM0037 or PRS-CM0038 ).
Reference Rod should be ordered separately.

Product Code PRS-CM0029 PRS-CM0033

Dimensions 300x190x70 mm 90x340x40 mm

Weight (approx.) 12 kg 4 kg

Product Code Product Description

PRS-CM0074 Cement Wet Sieving Apparatus

STANDARDS : EN 451-2

The PRS-CM0074 Wet Sieving Apparatus is used for determining the fineness of fly ash. The apparatus comprises of a special stainless steel sieve, 0.045 mm opening, a spray nozzle Ã? 17.5 mm with 17 holes Ã? 0.5 mm oriented and spaced to conform to the standards.

Supplied complete with a pressure gauge Ã? 80 mm and fittings for connection to the water supply.

Dimensions 250x150x150 mm
Weight (approx.) 2 kg