Aggregates are mixtures of sand, gravel, crushed rock or other bulk minerals used in construction, principally as a component of concrete, and in civil engineering. At CEMENTATION we supply aggregates for a range of core applications, from fill materials to aggregates that can be used in concrete, precast concrete, asphalt and for surface dressing. Aggregate plays an important role in concrete and construction part. We supply quality material which makes durable concrete with higher compressive strength and low permeability having better finish. We can supply a wide range of coarse, fine and blended aggregates in accordance with international standards.
We acquire rock mines and stone crushing plants and enable us to fulfil contract of any size. Progressive stages if crushing and screening enable us to produce a range of aggregate sizes (06mm to 65mm)
APPLICATIONS
Road and Highway surfaces
Constructions or Civil work
Railway Ballast
To make Concrete or Asphalt
Filling
Colloidal mill machine is a mechanical equipment that uses a combination of shearing, grinding, and high-frequency vibration to finely grind and homogenize materials. Its core components consist of stainless steel dynamic and static grinding discs, which achieve material refinement through high-speed relative motion.
Use for :
Food industry: homogenization of dairy products, grinding of chocolate, emulsification of jam/peanut butter, processing of bone paste, etc.
Chemical industry: pigment dispersion, lubricant homogenization, emulsified asphalt preparation, etc.
Pharmaceutical industry: ointment mixing, vaccine emulsification, oral liquid homogenization, etc.
Daily chemical industry: cosmetics emulsification, toothpaste grinding, detergent dispersion, etc.
Other fields: dispersion of architectural coatings, pulp processing in the paper industry, crushing of lithium battery base materials, etc.
Capacity are different . Capable of high rotational speed (such as 14000rpm) and ultra refinement (particle size 5-10 m)
Welcome cooperate!
* K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors.
It is also used for jointing chemical resisting stoneware pipes.
K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles.
The concrete surface needed protection should be dryed, clean and rough.
The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner.
When Bedding and Jointing Materials are the same.
On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints.
The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water.
Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic.
When Bedding and Jointing Materials are Different.
Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR
A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions.
PREPARATIONS OF MORTAR :
* Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan.
* Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar.
* In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared.
* The cement mortar will be used before it starts setting.
Manufacturer insulating light weight insulating refractory mortar castable is a kind of unshaped refractory made of granular and powdery material, in which add a certain amount of binder and water together. It has high mobility, is suitable for casting construction, and can be hardened without heating. Refractory castables consist of refractory aggregates, powders, binders, admixtures, water or other liquid materials. Generally in the use site, it is molded by pour, vibration or tamping method, and can be used as preforms. Refractory castables are mainly used in the metallurgical industry furnace, also in the petroleum, chemical, building materials, power and machinery industry furnace and thermal equipment.
We could offer you the best refractory castable as following:
1.High alumina castable.
2.low cement refractory castable.
3.corundum castable.
4.Self flowing refractory castable.
5.Corundum mullite castable.
6.Silicon carbide castable.
7.Zirconia Refractory Castable.
8.Lightweight insulation Refractory castable
Features and Advantages of refractory castable:
1. High refractoriness, High refractoriness under load.
2. High density, low porosity.
3. Good slag resistance and corrosion resistance.
4. High strength and wear resistance.
5. Good resistance to flake performance.
6. Good thermal shock stability.
7. Scouring resistance
8. Good hot strength.
Since ancient times, people have used hydrated lime to build houses and high buildings. Today, the massive architectural works and high-rise buildings are constructed more and more.
Why appear firm architectural construction?
That is cement â??important hydraulic binder in building process, helping to link projects together, forming a solid mass.
With modern advanced machines and science, abundant human resources.
Portland cement is the most common type of cement in general use around the world, used as a basic ingredient of concrete, mortar, stucco, and most non-specialty grout.
It is a fine powder produced by heating materials in a kiln to form what is called clinker, grinding the clinker, and adding small amounts of other materials. Several types of Portland cement are available with the most common being called ordinary Portland cement (OPC) which is grey in color, but a white Portland cement is also available.
High strength and high corrosionproof, provides long service life and convenient to fill and clean.
It provides wide applicability and can be widely applied for packaging in industries such as chemical engineering, petroleum, medicine and food etc.
Seal liquid test:Put the sealed barrel with liquid upside down or tap,the seal is at the lowest position,and no leakage within 24 hours.
The standard specifies blow-moulding technology requirements of the barrel, test methods and the rules and symbols, packaging, transporting and storage. This standard applies to polyethylene as the main raw material, barrels production through automatic blow molding machine,and this type of blow molding barrel is mainly used for solids or chemical products.
We also can help to change any design as your requirements. such as size,weight,color,capacity ect.
