Find Verified Enamel Paint Suppliers, Manufacturers and Wholesalers

Description
HY-330 contains specific high content of polymer resin, and can use with difference size of quartz sand to lay out sand texture.
It is non-toxic, eco-friendly, and can be applied on both interior and exterior wall, help enriching the monotonous surface.

Use
1.Interior and exterior wall decoration.
2.Enhance the finish surface by texturizing molding.
3.Other decoration usage.

Feature
1.Water-based, eco-friendly, and non-toxic.
2.Tough, durable, with good weather resistance.
3.Can prevent surface chalking of cement.

Series Product
HY-360/ Stone Plate Texture Coating

Feature: Reinforcement of Waterproof
High heat insulation
Good quality and dust resistance
Water resistance and high weather durable.
Drying faster and easy application.

Application
Cement wall
Galvanized steel
Color pre-painted steel
Plywood
Plastic wave-board
Lime-wall
The coverage will be affected by substrate
dimension and application method.
The loss factor as follow -
Brush= Theory coverage X1.4
Spray= Theory coverage X1.7

DESCRIPTION
CC-404 is a two component, high performance, pre filled epoxy grout , suitable for use as a pourable or fluid grouting material. Aftek F4 and F6 fillers may be added to produce a trowellable high build mortar or a pourable flowable grout.

FEATURES
â?? High flow properties
â?? Bonds to damp substrates
â?? Rapid hardening and strength gain
â?? High chemical resistance
â?? Pre-measured kits make for ease of use
â?? High tensile and compressive strength
â?? 100% solid epoxy
â?? Excellent adhesion to most substrates
â?? Cures at temperatures down to 5oC
â?? Negligible shrinkage
â?? High mechanical strength
â?? Solvent free High early strength

PACKAGING
CC-404 is available in 3 litre and 15 litre kits

Super wool roller covers, best paint pick-up and best paint release.
**any sizes (4", 7" or 9"...Etc.) available,
Any nap legth of fiber (3/8", 1/2"..Etc.)
Available,
Us. Type or european type available.


Each pc printing polybag, 60pcs each carton

Description
1. Tough film and good adhesion on the concrete, able to penetrate into concrete.
2. Good resistance to water , brine and chemicals. Excellent mechanical strength and physical properties.
3. Good resistance to impact and abrasion.
4. Easy application , drying fast.

Prepare to use
1. Mix base and hardener by the mixing ratio and Stir thoroughly, then setting at least 15 minutes. Thinner may be used to reduce viscosity.
2. Remove all foreign particles, oils, grease , rust and moistures from the surface before application.
3. Two packs product, must be used completely during the duration of its pot life.
4. Donâ??t apply when the temperature is < 10â??,>40â??, relative humidity is >90â?? or the surface temperature of substrate is not higher than the dew point for at least 3â??.
5. If the coating interval is exceeded , the surface of base coat must be roughened to insure adhesion.
6. Keep away from heat, sparks and flame.
7. Stored with good ventilation.
8. Keep adequate ventilation during application.
9. The actual coverage may vary, depending on application technique, job conditions and type of surface. Under brushing & rolling application the actual coverage is estimated at 70% of the Theoretical coverage and 60% for spraying.
**The parts of data base above could be affect by application condition at job site, please reference guide specification or contact with relative technical personnel.

Color : Clear
Drying time :
Tack-free : 2 hours
Hardness : 8 hours
Full cure : 7 days (grease)

DESCRIPTION
CC-604SP is two component water based epoxy primer, composed from water based of liquid epoxy resin and hardener.

APPLICATION
1. To prime the surface and help the following application procedure to mold and decorative coating.
2. Highly resist to chemicals in non-circulated places.
3. With well adhesion ability with epoxy system or PU system application.
4. Suitable for hospital, operation room, food factory to prevent the mold, dust and bacterium.

CHARATERISTIC
1. Able to be diluted by water.
2. Anti- efflorescence , suitable for the environment with highly hygienic request.
3. Good adhesion to the moisture surface, can take as the primer for solvent-free or solvent-based epoxy resin.

CS-613W is 2-component water-based premium epoxy product.
CS-613W as admixtures can improve the properties,
particularly in relation to water absorption reduction, toughness
enhancement, vibration damping and increase of the bond strength
of cement to reinforcements other than being used as admixtures,
CS-613W is used partial replacement of fine aggregate, for
coating, sealing and repairing concrete and for coating steel
reinforcing bars for corrosion protection.

AREA OF APPLICATIONS
Repair mortar for concrete areas.
Industrial flooring.
Bonding agent for new to old concrete.
As water based primer.
Can be applied with damp surface.

FEATURE
Weatherproof and waterproof of capabilities that help prevent the deterioration of the
ground-coat material.
Low odor.
Washable with water including tools. Best to wash as soon as possible before it hardens.100% water resistant when cured.

CA-010P as a water-based primer in relation to water absorption reduction and increase the bonding strength of cement to reinforcements other than being used as admixtures increase the mechanical properties and the adhesion of the hardened material.
AREA OF APPLICATIONS
Repair mortar for concrete areas
Industrial flooring
Bonding agent for new to old concrete
Enhance adhesion strength of mortar

DESCRIPTION
Bituminous Primer is product containing oxidized bitumen and a mix of technical quick
drying solvents.

APPLICATION
Bituminous Primer is recommended to block the dust and the porosity of concrete surfaces allowing the quick application o f the bituminous polymer membranes, both with flame application and cold bonding with bituminous sealants or with self adhesive membranes.Bituminous Primer allows quick film drying, has an excellent penetration and adhesion to the support for the absence of surface stickiness.

INSTRUCTIONS FOR USE
Concrete surfaces must be dry, clean and free from oil, dust or release agents.
This type of primer is ready for use after mixing it. Bituminous Primer can be either sprayed or applied by means of roller or brush. In case of hot application of membranes with flame, the primer can be used only if surfaces are completely dry. On the contrary, if the surface is damp, it is recommended to use a bituminous primer specific for damp surfaces. The drying time depends on concrete porosity, on the quantity of product applied and on the temperature of both the surface and the environment.
Usually the film gets dry after 2-4 hours from the application. The drying time can increase in case of cold temperature and with low a bsorption surfaces.

PACKING
5 gallon Bucket

SHELF LIFE
The product can be stocked in closed buckets and in dry area, far from UV rays for
12 months.

TOOL CLEANING
After use clean tools with common solvents.

DESCRIPTION
CC-600SP is a two component, solvent-free epoxy system with high chemical
resistance and high bond strength. The epoxy may be applied as a primer for most
high end industrial coatings, like Epoxies, PU.

CHARATERISTIC

Easy apply

Low odor

High bond strength

Abrasion resistant

Chemical resistant

APPLICATION

Concrete coating

Cement

1>. A5 size with 6-holes colored binder.

2>. Dimension of cover is 17.50 X 23.0 CM. Dimension of refill is 14.20 X 20.70 CM.

3>. The color of 6-hole binder is by plating not by spray paint. So, the color look more vivid as well as more durable. Color looks dull and easy to fade away if by spray.

4>. Color of the PU can be matched with the binder.

5>. The internal design/layout and the tab can be customized by the customer.

6>. We have at least more than thousands of colored changing PU in stock . So, customer could select color combination without considering the MOQ of the PU. For example, 1,000 PCS for 2 colors or 2,000 PCS for 4 colors. Low purchasing threshold of the material allows customers more flexibly design the color combination and diversify the market.

Item no.: NE-555M
Capacity: 10ml

Item no.: NE-478
Capacity: 15ml

DESCRIPTION
CC-604 is two components of water based surface paint, composed from water based of
liquid epoxy resin and hardener and special pigment.

APPLICATION
1. Waterproof of concrete wall, resist to mold and decorative coating.
2. Highly resist to chemicals in non-circulated places.
3. Suitable for hospital, operation room, food factory to prevent the mold, dust and
bacterium.

CHARATERISTIC
1. It is water based paint, and dilute by water, but its films strong after hard is not less
than solvent based epoxy resin.
2. With good light resist quality, uneasy to become powder or change color, suitable for
the environment with highly hygienic request.
3. Good to resist the radiation, can be used for the concrete wall and floor in the nuclear
power factory.
4. Good adhesion to the moisture floor, can take as the primer for non-solvent or solvent
based epoxy resin.

Use Japan Mitsubishi servo motor & Comparable software technic.





Wooden Case200cm*150cm*200cm