Snap-in type, can be mounted directly on PC board.
Some of output terminals can be also used as jumper leads, thus making circuit arrangement easy.
Available with anti-ESD ground terminal.
Although the recommended PC board thickness is 1.6mm, the models which can be mounted on PC boards of thickness 0.8 to 1mm are also available upon request.
Snap-in type, can be mounted directly on PC board.
Some of output terminals can be also used as jumper leads, thus making circuit arrangement easy.
Available with anti-ESD ground terminal.
Although the recommended PC board thickness is 1.6mm, the models which can be mounted on PC boards of thickness 0.8 to 1mm are also available upon request.
Snap-in type, can be mounted directly on PC board.
Some of output terminals can be also used as jumper leads, thus making circuit arrangement easy.
Available with anti-ESD ground terminal.
Although the recommended PC board thickness is 1.6mm, the models which can be mounted on PC boards of thickness 0.8 to 1mm are also available upon request.
Micro Switch action is PUSH-ON TYPE S.P.D.T
Contact resistance measurements shall be made with a 1KHz ± 200Hz max
DC 5V 1A contact resistance meter.
Insulation resistance measurements shall be made following application of DC 500 V potential across terminals and across terminals and frame for one minute.
The travel distance for the plunger to come to a stop shall be measured
200 Ehv Switch Yards Suppliers
Short on time? Let Ehv Switch Yards sellers contact you.
Detector Switches is applied to low current circuit (Secondary circuit) push switch
used for electronic equipment.
Appearance of the Switch shall have good finishing and shall have no rust, crack of plating failures.
Terminal Strength of a static load of 3N(306 gf) shall be applied to the tip of terminal in a desired direction for 1 minute. The number of test shall be once per terminal.
Hook Switch is applied to low current circuit hook switch for electronic equipment.
The standard test conditions shall be 5~35 in temperature, 45~85% RH and 860~1060 m bar.
Storage temperature range : 30 degree Celsius to 80 degree Celsius, however 96 hours maximum for continuous storage over a range
Compact size and unibody type
Excellent EMI/EMC and noise properties
Embedded ASIC for high accuracy
Wide range(-40 to 100°C)
DIN and cable type
Perfect compatibility with dotech's air compressor controllers
* Economical price.
* Housing and brackets are all made of press-formed stainless steel.
* The mounting bracket designed can adjust the height.
* Lightweight and robust design.
Consistent control is available by always maintaining the standard time in application of GPS receipt for compensating the present time to the electronic Guard Lamp switch, and this product does not require a separate compensation because the light On/Off time according to the region is compensated automatically.
Consistent control is available by always maintaining the standard time in application of GPS receipt for compensating the present time to the electronic Guard Lamp switch, and this product does not require a separate compensation because the light On/Off time according to the region is compensated automatically.
- dpc-series : dual , single pressure control,
Switch & gauge type spdt
- mpc-series : dual, single , oil pressure
Control, switch & gauge type spst
- pressure range: low -1-50kgf/cm2g,
High -1-50kgf/cm2g,
High differential 3 fixed kgf/cm2g,
Low differential 0.1kgf/cm2g,
Reset low auto, reset high auto/manual,
Pressure connection 7/16-20 unf
(1/4 in flare ), mounting any position,
Voltage 12/24/240, includes nema 1 enclosure,
Nonconductive cover r-12, r-22, r-134a and
R-404.410a.407.Co2 commercial refrigeration and air conditioning
- rapid trip (pressure measurement speed: 1:1)
- built-in gas temperature indicator for each coolant
- pressure display in kgf/cm2, mpa, bar, and psig
- built-in oil alarm delay timer
- built-in rs-485 communication function program (optional)
Tact Switch MT 1101 SE is applied to low current circuit tactile switch for electronic equipment.
Storage temperature range 96 hours maximum for continuous storage over a range
The standard test conditions shall be 5 ~ 35 degree Celsius in temperature.
Tact Switches MT 1101 Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1 kHz small-current contact
resistance meter.
Insulation resistance measurements shall be made following application of DC 100 V
Potential across terminals and frame for one minute
Tact Lever Switches is applied to low current circuit push switch for electronic equipment.
Appearance of the Switch shall have good finishing, and no rust, crack or plating failures.
Operating force of a static load shall be applied to the tip of actuator in operating direction.
Robustness of terminal of a static load of 2N(200gf) shall be applied to the tip of terminal
in a desired direction for 1min. the test shall be done once per terminal.
Tact Switch MT 1101 S is applied to low current circuit tactile switch for electronic equipment.The standard test conditions shall be 5 ~ 35 degree Celsius in temperature.
45 ~ 85% RH and 860 ~ 1060 m bar in atmospheric pressure.
Should any doubt arise in judgement, tests shall be conducted at 20±2 degree Celsius, 60±5% RH
Dotech's complete solutions against refrigerant leak and noise
Accurate measurement with dedicated sensors (low and high pressure refrigerants)
Display of saturation temperature of refrigerant
All in one (pressure switch and gauge)
Easy installation
200 Ehv Switch Yards Suppliers
Short on time? Let Ehv Switch Yards sellers contact you.
