Skid Resistance And Friction Tester

The tester is used to determine the impact resistance of plastic tube. The design of the tester is accordance with DIN-EN 744, BS-EN 1411, and ISO-3127.

Brief introduction:
Lt-01 leak tester is designed for the examination of airproof property of packages, containers, bags, pipes. Lt-01 package air proof tester is widely used in food, beverage, pharmaceutical, daily chemical, electrical and electronic industries, etc. Lt-01 leakage tester complies with astm d3078 and gb/t 15171 standards.
The leak detection system is composed of the mainframe and the vacuum chamber. A test sample is placed into a vacuum chamber with water and the air above water level is evacuated by a venturi vacuum ejector. A great pressure difference is created inside and outside the sample and any slight leakage can be observed and identified when the sample is inflated.
Features
Lt-01 leak tester uses vacuum ejector to generate stable vacuum environment. .
The leak detection requires no electricity
High leakage test efficiency
Extra-thick perspex
Different chamber sizes available
No calibration needed
No vacuum pump required
Easy installation, start-up and operation
Low maintenance

Astm d3078 , gb/t 15171

Brief introduction:
Lt-02 leak tester is designed for the examination of airproof property of packages, containers, bags, pipes. Lt-02 package air proof tester is widely used in food, beverage, pharmaceutical, daily chemical, electrical and electronic industries, etc. Lt-03 leakage tester complies with astm d3078 and gb/t 15171 standards.
The leak detection system is composed of the mainframe and the vacuum chamber.
A test sample is placed into a vacuum chamber with water and the air above water level is evacuated by a venturi vacuum ejector. A great pressure difference is created inside and outside the sample and any slight leakage can be observed and identified when the sample is inflated.
Features


Astm d3078 gb/t 15171

Brief introduction:
Lt-03 leak tester is designed for the examination of airproof property of packages, containers, bags, pipes. Lt-03 package air proof tester is widely used in food, beverage, pharmaceutical, daily chemical, electrical and electronic industries, etc. Lt-03 leakage tester complies with astm d3078 and gb/t 15171 standards.

The leak detection system is composed of the mainframe and the vacuum chamber. A test sample is placed into a vacuum chamber with water and the air above water level is evacuated by a venturi vacuum ejector. A great pressure difference is created inside and outside the sample and any slight leakage can be observed and identified when the sample is inflated.
Features
Lt-03 leak tester uses vacuum ejector to generate stable vacuum environment. The state-of-the-art human-computer interface and plc control unit on the leakage detection system make the parameter setting and test operation direct and easy. By saving different groups of parameters, users are free from the troubles of setting parameters each time before use. At the same time, different testing results and total test numbers can be saved to avoid any human errors.

1. Leak test process all automatic
2. Touching screen operation
3. Digital vacuum degree and test time input
4. Parameters and test data automatic saving
5. Automatic vacuum maintenance and air back-flushing
6. Extra-thick perspex
7. Different chamber sizes available
8. No vacuum pump required
9. Easy operation and maintenance


Astm d3078 , gb/t 15171

Application and Brief Intro
LSST-01 Leak and Seal Strength Tester is suitable for the quantitative determination of sealing strength, heating sealing quality, burst pressure and leakage of flexible and aseptic packages. The Leak and Seal Strength Detector can also be used to determine the sealing performance of pilfer-free bottle caps and soft tubes. The compression strength, connection strength of cap and body, cap losing strength, seal strength and butting strength of tubes are the applications of LSST-01 Seal Strength Testing System.
This Seal Strength Testing System conforms to standards of ISO 11607-1, ISO 11607-2, ASTM F1140, ASTM F2054, GB/T 10440, GB 18454, GB 19741, GB 17447, GB/T 17876, GB/T 10004, BB/T 0025, QB/T 1871, YBB 00252005, YBB 00162002 .
Principle
The three test modes of the positive pressure method, which LSST-01 Leak and Seal Strength Tester satisfies are as follows:
A. Burst Test: LSST-01 Leak and Seal Strength Tester internally pressurizes the packages until the package fails. The test pressure is the maximum pressure detected before the package fails.
B. Creep Test: Pressurize the package internally to a specific pressure and maintains this pressure for a specific time. The test measure is pass/fail.
C. Creep to Failure: The package is creep-tested and held until the package fails. The pressure setting is higher than that of the creep test to ensure the package fails in some time. The measure is the time until failure.

Application and Brief Intro
HST-01 Heat Seal Tester is for the determination of the heatsealability of a surface, or sealant layer of films, laminates, composites and polymers etc. How well the material heatseals is expressed quantitatively as seal strength as a function of the sealing conditions of temperature, time and pressure. HST-01 Heat Seal Tester is professionally designed for the precise measurement of the three parameters of temperature, time and pressure in the heat seal process. HST-01 Heatsealability Tester conforms to standards of ASTM F2029, QB/T 2358 and YBB 00122003.

Principle
Place a sample between two-heated sealing jaws of HST-01 Heat Seal Tester with flat surfaces when the required temperature reaches equilibrium. The upper seal jaw, driven by a gas cylinder, is pushed down, to exert a certain pressure on the sample and remain for some time. When the preset sealing time ends, the upper sealing jaw returns to its original position and the whole heatsealability testing process finishes.

ASTM F2029, QB/T 2358, YBB 00122003

Tray thermal extension test apparatus
Aging Testing Instrument
I. Product introduction:
Test standard: It is in line with Standard GB/T2951-2008 and Standard GB5013-2008, and it shall be used together with aging test chamber.
II. Key parameters:
Maximum number of samples in a test:3
1, temperature setting: rubber products, 180 , crosslinked polyethylene products 200 .
2. When the temperature rises to the required temperature, clamp the dumbbell test piece onto the hot extension clamping device, and add the weight below.
3. Weight distribution calculation: 20.4 x specimen thickness * 4(including clamps, supporting rods and weights).
4, in the middle of the dumbbell specimens on the effective distance of 20 mm (the length of the small dumbbell specimen is 10 mm) tag line, the length of the dumbbell to take three, put hot stretch of a complete set of equipment in have ascended to the temperature of the central part of the aging box.
Close the door of the aging chamber and read the elongation of the specimen after 15 minutes.
We are Cable Detection Equipment Factory

Fsm-60LE glass surface stress tester

Product name: fsm-60LE glass surface stress tester
Supply ability: 100
Specifications fsm-60LE
Price term: fob
Port of loading: shanghai
Minimum order 1
Unit price: negotiable


Fsm-60LE accurate measurement of chemical and heat-resistant glass surface stress. Birefringence in the measurement principle is very important. Sodium lamp as light source, measurement pattern is very clear. The chemical products suitable for measuring the stress and the surface of tempered glass containers depth.



Original packing.