Poe Injector 12V 24V 15V 0.5A 1A 2A Poe Adapter

Input Voltage 12V / 24V DC optional
Output Voltage 115V / 230V AC optional
Portable power for AC products, AC outlets for connecting multiple loads
High surge capacity for products that require more power to start
High efficiency converts virtually all of the battery's power to AC
Mounting brackets for convenient installation
Heavy duty stud-connection mounting
RS232 communication port
WIFI/BMS Optional
Overload and over temperature shut down
Low voltage and over voltage alarm/cut off
Input reverse protection
Short circuit protection
PI15 series is a pure sine wave inverter, high frequency machine solution, the product is small size, the solution is reliable and stable, the main function is to invert the DC 12VDC battery or 24VDC battery to AC 230VAC or AC 115VAC output, mainly used for emergency use Electricity, car inverter,
outdoor electricity and other occasions.

Features :
3 times peak power, excellent loading capability.
Combine inverter/solar controller/battery all in one.
Multiple output : 2*AC output socket, 4*DC 12V, 2*
Working mode AC prior/ECO mode/Solar prior selectable
AC charging current 0 1 0A selectable.
LVD/HVD/Charging voltage adjutable, suitable for kinds of battery
Adding fault code to monitor real time work situations
Continuous stable p ure sine wave output with inbuilt AVR stabilizer .
Digital LCD and LED for visualization of operation status of the equipment.
Inbuilt automatic AC charger and AC mains switcher, stwitch time 4ms

Single-port Ethernet power supply equipment, which is suitable for indoor use, can work normally from 100VAC to 240VAC input voltage. The power supply and network terminal equipment are connected by over five types of cables. It has an Ethernet data port and an output port after data and power combination. This device can provide POE power supply applications in line with IEEE802.3af/at international standards for all Ethernet devices, such as routers, switches, wireless AP, network telephones, industrial network terminals, network cameras, etc. It can also provide efficient engineering in places where power supply cannot be provided remotely or where power supply by Ethernet network lines can be used to improve system reliability and simplify equipment installation.

Product Description
We produce VRLA/SLA Battery, lead battery, Industrial Battery, 12V/ 6V Battery, Rechargeable Battery, Gel Battery, Deep Cycle Battery, sealed lead acid battery and so on.

12v 7ah backup battery (20hr battery)

Valve regulated lead acid series UPS batteries are designed with AGM (Absorbent Glass Mat) technology, high performance plates and electrolyte to gain extra power output for common power backup system applications widely used in the field of UPS, Emergency Lighting System.

Battery Structure
1. Container/Cover: Made of UL94HB and LU 94V-0 ABS Plastic
2. Negative Plates: Use the special PbCa alloy grids, optimize the recombination efficiency and less gassing.
3. Separator: Import high quality AGM separator.
4. Postive Plates: PbCa grids minimize corrosion and prolong life.
5. Terminal post: Cooper material with maximum conductivity, enhance the high current rapidly.
6. Vent Valve: Allows the release of excess gas automatically for safety.
Power Supply 12V 7ah UPS Backup Battery (20hr battery)

Basic Parameters
Dimensions: 201 x 99 x 35 mm
Weight: 333g
Adapter Input: AC 100 ~ 240 V Output: DC 24V 2.65A
Display mode
Segment LCD with white backlight + LED in red and green
Function Introduction
Charge
Active, pre-charge, constant current and constant voltages are the stages of charging mode. The initial charging mode depends on the battery voltage, so active and pre-charge don't happen to every batteries. For charging mode and current, please refer to the paragraphs of charging mode and charging current on page 2 & 3.
Tester will stop charging if one of the conditions below was met.
1) Remaining capacity 99% & current intensity = 0
2) Remaining capacity = full charge capacity
3) Current intensity reduce to end charge current when constant voltage charge
4) Remaining capacity reach up the set value
Discharge
Constant current discharge for double loads
Inner load: 0 ~ 1000mA, adjustable continuously via Battery Manager
External load: 0mA, 500mA, 1000mA, 1500mA, 2000mA, five gears with dip switches offered
Tester will stop discharging if one of the conditions below is met.
1) Remaining capacity set value
2) Voltage set value
3) Current intensity reduce to zero
Remarks:
Many batteries can not measure exact current intensity, which cause an else current value appears after you set a value. However, the actual discharging current is the same with your set value.
Test
Testing time is 12 seconds and the purpose is to check both the charging and discharging performances. After finishing test, LED flickers with green color and LCD reports the test result.
Normal: Test OK Shown on LCD
Abnormal: Test NG Shown on LCD
Possible causes and solutions for the abnormal:
1) Cause: battery voltage is too low to discharge
Solution: try to charge the battery to raise voltage
2) Cause: remaining capacity is too full to charge any more
Solution: try to discharge the battery to reduce the remaining capacity
3) Bad contact of battery connecting wires
4) Damaged battery
5) Tester trouble
Capacity Correction
The battery capacity value in the battery management chip will different from the actual capacity after a battery goes through many recycling cycles. It will affect the use of the battery when the difference reaches a certain degree. Capacity correction is to deep discharge a battery and then fully charge, which will correct the capacity value in the battery management chip.
Remarks:
Discharging current can be set via Battery Manager. Deep discharge will cause a battery losing communication with tester, so battery dropping phenomenon may happen in the discharging process if the end capacity and voltage are set too low. In such a case, active charge will make the battery work again.
50% Capacity
CD50%: charge firstly, and then discharge to 50% capacity
DC50%: discharge firstly, and then charge to 50% capacity
Online Functions
Tester can be connected with master machine via a USB port. Users can monitor, control and set parameters via Battery Manager software in the master machine.
Monitoring
Battery information can be monitored via three windows.
1. Home screen
Battery bar and brief information can be read on home screen.
2. Battery detail information window
Show smart battery data in real time and the data can be saved and printed in image format.
3. Battery graph window
Voltage, current and capacity are traced in curves.
Control
Battery Manager can control slave machine completely. Right-click menu on the battery bar includes the related commands.
Attention
All the functions of charge, discharge, capacity correction and 50% capacity are comply with the charging discharging conditions, which are showed on function introduction paragraph in page 4 & 5, so parameters should be set reasonably. Especially, deep discharge will cause a battery losing communication with tester.
Others
1. Active cooling
2. Active batteries of zero voltage
When a battery is deep discharged, the discharge protection circuit will start up and the voltage in the battery connector will become zero voltage. In this case, an appropriate voltage should be supplied to active the battery.
3. Battery identification
Battery information can be read from battery management chip after establishing communication.
4. Intelligent protection
Against over-current, over-voltage, over-charge, over-heat and short circuit.
5. Fan
Discharging mode: fan startup
Other modes: fan startup when temperature above 48
Fan stop working when temperature below 40
6. Trouble alarm
LED flickers in red color and current command stops when one of the conditions below happen.
1). There is not current for around 50 seconds when charge.
2). There is not current for around 25 seconds when discharge.
3). Charging time is above 8.8 hours.
4). Discharging time is above 9.9 hours.
5). Suitable for almost all laptop batteries, above 95%
Structure
Accessories
1).1 * adapter
2). 1 * USB cord
3). 1 * CD
4). 13 * connectors
5). 10 * cables
6). 10 * jumpers
7). 1 * loader

Standard Export Carton

1024 mac address
Standard

Norms

Network protocolsiee 802.3i 100base-t, iee 802.3u 100base-t
Iee 802.3x flow control, iee 802.3af power over ethernet,
Power

Support

Led indecatorpower, each port speed, connectivity. Poe active, poe fault
Max power support poe90w¡ê¡§port 1-port 4¡ê©maximum 15.4w per port
Max power
96w, 48v/2a dc output

Power1, 2(+);3, 6(-) (endspan)
Data1, 2-tx; 3, 6-rx
Power supply modedetect pd, then power support
Otherselectromagnetic compatibility ce class b/fcc part15, class b/vcci class b/c-tick
Safety normsce/lvd
Operating temperature0¡ã¡a40¡æ
Operating humidity10%-90%, non-condensing
Physical

Specifications

Dimension(mm)
225mm*121mm*35mm
Weight¡ê¡§kg¡ê©

1kg(including package)

Dimension(mm)
225mm*121mm*35mm
Weight¡ê¡§kg¡ê©

1kg(including package)

Model XD-POE-012
Output power¡ê¡§W¡ê© 12
DC output 15V/0.8A
50 PCS per carton,13KG

Power supply 12V/1A power adaptor.
Laptop Adapter,
CCD Camera Lenses, Dome CCD Cameras, CCD Camera Parts and Accessories, CCD Cameras, CCTV Components, CCTV Decoder. CCTV Monitors, Infrared Illuminators, Quad Processors, Wireless CCD Cameras, Bracket, Housing, DVR.



Power supply 12V/1A power adaptor.

12v 5a ite power supply(MOQ:100pcs)
Product type:interchangeable type
Model:YHY-12005000
input:100-240Vac,50-60Hz,1.5a
output:12vdc 5amp 60 watt
plug version:US+EU+UK+AUS plugs
dc wire length:1.2M
dc tip size:OD5.5*ID2.1MM
Certifications:CE,GS,ROHS,UL,UKCA,PSE,SAAC,-C-Tick