The polyester staple fiber machine (PSF plant) takes virgin PET Chips, recycled Bottle Flakes, Popcorn and Lumps, etc., as raw material, with continuous drying (or batch drying through Vacuum Dryer), high pressure melt spinning process engineering and VFD controlled Spinning & Stretching process engineering to produce normal Staple Fibre, High Tenacity Low Elongation Staple Fibre and Hollow Fibre. Single plant capacity is 15T.P.D. to 80T.P.D.
Equipment Technical Data
Titer Range dtex 6.67-16.67
Spinning Pos. nos. 6-24
Spinning Pitch mm 700, 750
Plant Capacity TPD 15-80
Spinneret dia. mm 328, 358, 410
Spinning Mechanical Speed m/min 500-1,500
Spinning Processing Speed m/min 500-1,300
Stretching Mechanical Speed m/min 240
Stretching Processing Speed m/min 230
Total Tow Titer at Stretching dtex 600,000-3,000,000
Stuffer Box Width mm 160-410
Cutting Length mm 25, 32, 38, 44, 51, 64, 76, 101
Bale Weight kg 200-350
Application:
Cushions Pillows Quilts Toys Jacket Mattress Non woven carpet Automotive felts, speaker felts, geo textiles, polyfill wadding, filter fabrics and other acoustics as well.
Drawing line: Can Creel Inlet Thread Guide Tow Guide Stand Dipping Bath 1st Draw Stand Draw Bath 2nd Draw Stand Draw Steam Chest 3rd Draw Stand Tow Stacker Crimper Steam Box Crimper Silicone Oil Sprayer Machine Tow Tension Stand Cutter Fiber Spreading Machine Relaxer Fiber Blowing system Baling Press
1, before commissioning must ensure that the pump and pipeline full of water, so as not to damage the pump.
2, the pump is filled with water to open the pump bleeder valve for exhaust, so as not to cause unstable pipeline pressure can not be normal pressure regulation.
3, the cabinet door on the surface of the manual stop automatic transfer switch, hit the manual for the frequency start, automatic inverter start by the outlet pipe remote pressure gauge according to the set pressure automatic control.
4, due to manual and automatic power supply into the line is not the same, so the manual and automatic pumps are not the same, all pumps to work manually are adjusted to the positive, automatic reversal of the frequency converter output on the U2, V2, W2, any two-phase switching can be.
5, set the pressure to stop the pump (i.e., the maximum pressure) just press (ENTER) on the inverter panel into the display (REF) and then press (ENTER) into the display of 40% (i.e., 0.4MPa pressure), such as the need to increase and decrease the pressure according to the (Increase key) or (Decrease key) to set the required pressure value (i.e., the pressure stop the pump), set the value of the pressure and then press (ENTER) to save, then the After setting the pressure value, press (ENTER) to save it, and then press (EXIT) to return to the main interface to complete the setting; the pump pressure is based on the highest pressure to be converted by itself without setting.
The ball press is also called: coal ball machine, egg coal ball machine, strong ball press, mineral powder ball press, roller ball press and so on.
Ball press is mainly used for making balls and blocks of nonferrous and black metal ore powder, smelting directly into the furnace to improve added value. The ball press is mainly used for the treatment of mineral tailings, pressing the powder material which is difficult to form. It is characterized by high forming pressure, adjustable rotation of the main engine and spiral feeding device.
By belts, to gear reducer, gear reducer through coupling, to drive shaft by a pair of open gear again, ensure that the two roller synchronous (reverse) uniform material storage bin after quantitative device evenly into the forming hopper, units of the molding pressure of material changes from small to big, in the peak of roll center of moulding pressure, material after the line, The forming pressure decreases rapidly so that the material enters the depelleting state and depelleting smoothly.
This machine compares the easy material, such as coke powder, oxide iron sheet, dust removal, coal slime, all kinds of metallurgical powder, sponge iron carbon products and other materials have obvious effect, special effect.
(1). This Wood Pellet Production Line mainly used for making wood pellets , the pellets used for industry, boiler factories , the machine can be produce diameter is 6mm,8mm,10mm,12mm pellets.
(2)The machine adopt imported SKF or NSK bearings, the motor brand is Siemens or china famous Wannan brand
(3)Driven by gear .more strong than by belt, and the capacity 10% higher than by belt .
(4)the machine also matched the safty equipment , once overload , the safty pin will crack, to protecting the machine lifetime
Wood Pellet Production Line Main data:
1.Name:Wood Pellet Production Line
2.Model:MZLH420
3.Capacity:1-1.2t/h
4.Main Power:90kw
5.Feeder Power:1.5kw
6.Force Feeder Power:1.5kw
7.Die Diameter:420mm
Supplier: Precision accurate leak testing machines, various testing rigs as per international standards, special purpose machines (spm), industrial automation, conveyors, assembly lines, robotic applications, bearing pressing machine, condenser & radiator fin inserting machine, industrial component washing machine, high pressure flow test machine, single piece movement complete assembly lines, life cycle test machines, torque testing machines, work stations, jigs & fixtures, shock absorber testing machines.
Introduction
MJKC-1 Series Paperboard Cutting, Pressing Line, Slotting & Cutting corner Machine is and integrated machine used for the cutting, slotting, pressing line and corner cutting of corrugated paperboard. Its special characteristics are high production efficiency, good quality and easy operation. (We can also add the function of holing and carton window on this machine.)
Technological Parameters
Model
Max. Paperboard size (mm)
Min. Paperboard size (mm)
Slotting Depth (mm)
Work Speed (m/min)
Fin line is consist of uncoiler, lubricator, fin die taking out system, fin stamping die , press, suction unit, stacker and scrap collecting device; a hydraulic withdrawal feature is incorporated into the press slide allows access to the inner tooling of the stamping die without removing the die from the press; our fin lines provide the perfect fin making systems for your mass or heavy production coil purpose and smallest coil shops. Whatí»s more, jdm jingda can also offer larger tonnage systems as 160 metric tonnage capacity for your steel fins or other industrial heat transfer application; however we would like to design and customize your fin lines based on your product specification by contacting our sales manager.
Supplier: Grinding / polishing line for marble/granite/ceramic tiles/quartz stone slabs, hydraulic press, cold extrusion press, water bulging press, metal powder forming press, door panel forming press.
