Sintered Wire Mesh Filter Element Feature
1. Sintered wire mesh filter element is surface filtration
2. Sintered wire mesh filter element is good for backwash because the pore passage of zwen sintered wire mesh aperture is very smooth
3. Sintered wire mesh filter element has uniform pore size distribution
4. Wire mesh will not shed in filtration process
5. High compression strength
6. High mechanical strength
7. High rigidity
8. High abrasion resistance
9. Good durability against most liquids, gases and aggressive steam
10. High temperature resistance
11. High filter rating accuracy
12. High filter efficiency
13. Good corrosion resistance
14. Washable and Cleanable
15. Reusable
16. Long service life
Sintered Wire Mesh Filter Element Technical Parameter
Raw Material: SS 316L, SS 304
Filter Media: ZWEN Sintered Wire Mesh
Filter Rating: 0.5-300 Microns
Filter Efficiency: > 99.99 %
Operation Temperature: â?¤ 816
Outside Diameter: 10 mm, 15 mm, 25 mm, 30 mm, 50 mm, 60 mm, 63.5 mm, 65 mm,100 mm,150 mm, 250 mm, 380 mm, 500 mm or others
Length: 40 mm, 90 mm, 127 mm, 254 mm, 508 mm, 762 mm, 1016 mm or others
Gasket: PTFE, Viton, Silicone, Buna-n, EPDM
Connector:
1. DOE
2. 220
3. 222
4. 226
5. Thread (NPT,BSP,G,M,R)
6. Flange
7. Special customization
Application
Polyester filtration, polymer filtration, high viscosity filtration, fuels and lubricants filtration, oil filtration, steam filtration, high temperature gas filtration, high temperature liquid filtration, steam filtration, potable and process water filtration, beverages filtration, detergent filtration, solvents filtration, pharmaceutical industry, chemical industry, chemical fiber industry, food industry
Anping County Longyi Mesh Manufacture Co.,Ltd produing sintered disc filters consist of highly uniform, interconnected networks of pores with tortuous paths that trap solid particles in gas or liquid. Excellent depth filters with superior mechanical strength. Stainless Steel Type 316L withstands temperatures up to -100�°C in oxidizing and 600�°C in reducing environments. These filters can be cleaned by other methods, such as ultrasonic baths or reverse flow flushing. If your application requires even greater resistance to corrosion, temperature, wear, and vibration, other nickel-based alloys are available.
Want more information or would like to receive a quote?
40 Micron Stainless Steel Sintered Wire Mesh Filter Element is a type of filter that is made by sintering multiple layers of stainless steel wire mesh together. Sintering is a process that involves compacting and heating a material without melting it, which causes the particles to fuse together and form a solid mass.
40 Micron Stainless Steel Sintered Wire Mesh Filter Element consists of multiple layers of wire mesh that are stacked and then sintered together. The sintering process creates a solid bond between the wires, resulting in a robust and durable filter element that can withstand high temperatures, pressures, and corrosive environments.
Parameter
Material: stainless steel
Grade:SS 316L, SS 304L, SS 316, SS 304
OD: Max. 200mm
Length: Max. 1500mm
Accuracy / Pore Size: 0.2um-200um
Porosity: 30%-60%
Temperature resistance: â?¤300â??
Technique: Sintering Process
Surface: Smooth, clean and metallic
Feature
40 Micron Stainless Steel Sintered Wire Mesh Filter Element has several advantages over other types of filters.
First, it has a uniform and controlled pore size, which ensures consistent filtration performance. Second, it has a high dirt-holding capacity, which means that it can capture a large amount of contaminants before needing to be cleaned or replaced.
Third, it has excellent mechanical strength, allowing it to withstand high pressures and mechanical stresses.
Fourthly, it can be cleaned and reused, making them a cost-effective and environmentally friendly filtration solution.
Product Introduction
The stainless steel wire mesh sintered filter element is a derivative product of stainless steel sintered mesh. In this filter material, the wire woven mesh is laminated and vacuum sintering to create a multilayer wire mesh, which is strong mechanically.
The stainless steel metal sintered mesh filter structure generally contains five layers, which are divided into five parts: protective layer, filter layer, separation layer, support layer and reinforcement layer. The standard five-layer screen thickness is 1.7mm.Thermal and processability, it is a filter material with good filtering effect, high strength and long service life.
Product parameters
Name: Stainless steel wire mesh sintered filter element with high mechanical strength for oil pipeline filtration
Structure: standard five layers
Filtration accuracy: 2-200m
Working temperature: -200-650
Size: customized
Filtration accuracy: 1-200 microns
Product Features
1. High mechanical strength
2. High temperature resistance, corrosion resistance
3. High filtering precision
4. Strong and durable
5. Easy to process
6. Easy to install.
Applications
Mainly used for pipeline filtration in petrochemical industry.
40 Micron Stainless Steel Sintered Wire Mesh Filter Element is a type of filter that is made by sintering multiple layers of stainless steel wire mesh together. Sintering is a process that involves compacting and heating a material without melting it, which causes the particles to fuse together and form a solid mass.
Parameter
Material:stainless steel
Grade:SS 316L, SS 304L, SS 316, SS 304
OD: Max. 200mm
Length: Max. 1500mm
Accuracy / Pore Size: 0.2um-200um
Porosity: 30%-60%
Temperature resistance: â?¤300â??
Technique: Sintering Process
Surface: Smooth, clean and metallic
The function of each layer in the five-layer stainless steel wire mesh sintered filter element:
Outer Protective Layer: The outermost layer of the filter element is usually a coarse mesh that serves as a pre-filter to capture larger particles and prevent them from clogging the finer inner layers. This layer also protects the finer inner layers from damage.
Intermediate Protective Layer: The second layer is also a coarse mesh that provides additional protection to the finer inner layers. This layer helps to prevent the filter element from being damaged by high-pressure or high-velocity fluid flows.
Inner Filter Layer: The third layer is composed of a finer mesh size and serves as the primary filter layer. This layer is responsible for capturing smaller particles that were not captured by the outer protective layers.
Reinforcing Layer: The fourth layer is a coarser mesh size than the inner filter layer and serves as a reinforcing layer. It provides mechanical support to the inner filter layer and helps to prevent it from collapsing under high-pressure or high-velocity fluid flows.
Inner Protective Layer: The fifth and final layer is the finest mesh size layer that provides additional protection to the inner filter layer. This layer captures the smallest particles and prevents them from passing through the filter element.
Feature
40 Micron Stainless Steel Sintered Wire Mesh Filter Element has several advantages over other types of filters.
First, it has a uniform and controlled pore size, which ensures consistent filtration performance. Second, it has a high dirt-holding capacity, which means that it can capture a large amount of contaminants before needing to be cleaned or replaced.
Third, it has excellent mechanical strength, allowing it to withstand high pressures and mechanical stresses.
Fourthly, it can be cleaned and reused, making them a cost-effective and environmentally friendly filtration solution.
Application
1.Chemical Processing
2.Oil and Gas Industry
3.Food and Beverage Processing
4.Pharmaceuticals
5.Water Treatment
-Name:Titanium wire mesh
-Material:TA1, TA2, GR2, GR3, R50250, Titanium alloy etc.
-Mesh count:
Plain weave up to 200 mesh,
dutch weave up to 70x400 mesh
-Wire diameter: 0.05mm-1.8mm
-Width: 0.5m-2m
-Feature:
--Low density and high specific strength
--Outstanding corrosion resistance. In the corrosion environment, the surface of high purity titanium mesh will form an oxidation film layer to protect wire mesh from being corroded. The layer is compect and insert, which has strong resistance to corrosion. It has excellent corrosiion resistance performance in below environment: seawater, wet chlorine, chlorite and hypochlorite solution, nitric acid, chromic acid, metal chlorides and organic salts etc.
-Application:
Shipbuilding, war industry manufacturing, chemical filter, mechanical filter, desalination filter, high temperature vacuum equipment, medicine filtration industries etc.
longyi wire mesh company provides the ultra fine nickel wire mesh, nickel alloy based wire mesh.. which is widely used in the battery, electronic battery,,,
the mesh size can be from 1-600 mesh,
Our Quality IBC liner steel cage WIRE MESH FOR IBC TANK FRAME are great steel cage mesh for IBC Frame for use in Hotels, Garment Shops, Building Material Shops, Manufacturing Plant, Machinery Repair Shops, Food & Beverage Factory, Farms, Restaurant, Home Use, Retail, Food Shop, Printing Shops, Construction works , Energy & Mining, Food & Beverage Shops, Other, Advertising Company.
The Core Components Includes PLC, Engine, Bearing, Gearbox, Motor, Pressure vessel, Gear, Pump
*Customized product can be produced once negotiated.
*Other material including 304, 310, 904L, Duplex, Inconel, Hastelloy and Monel also available for custom needs
Sintered wire mesh type A specification:
Thickness: 1.7(mm); Porosity : ~37%;Weight kg/m�²: 5-layers sintered wire mesh (8.4) 6-layers sintered wire mesh (14.4)
Sintered wire mesh is the combination of different layer of wire mesh sintered under high temperature inert gas inside the furnace. During the sintering (diffusion bonding) process, individual wires and each adjacent layer of the mesh bond to each other.After cooling, the sintered wire mesh is rigid and completely flat readily to be finished.
Fatures :
(1).SS316 is used as standard material giving excellent heat and corrosion resistance.
(2).Extremely resistant to vibration, impact and wear.
(3).No delamination, expansion or media migration.
(4). Good cleanability and permanent reusability.
(5). Excellent workability for forming(caulking, brazing and welding)
Specifications:
(1)Material: SS316, 904L, Monel, Inconel, Alloy20, Duplex, Hastelloy
(2). Operating Temperature::-100 â?? to 380â??
(3). Dimensions:500*1000mm,600*1200mm,1200*1200mm,1200*1500mm (flat plate)
Note: any shape or structure is avaliable.
Our Advantages
Sales:
* One to one service.
* Quick respond in 24 hours.
OEM and design:
* Fully customized from raw mesh to part number engraving, according to your drawing.
* Design and CAD ability to meet your specific requirement in various application.
Quality:
* Bubble point test and other laboratory test to ensure functionality.
* ISO9001 management system to maintain quality consistency.
Product packaging
Robust packaging for safe delivery.
Various delivery methods to meet customer's need.
Anping Longyi Mesh Manufacture Co.,Ltd =. was founded in 2007. The company introduces foreign advanced production and testing equipment, production technology and technology, and adopts world-class quality filter materials as the main filter material, specializing in the production of porous metal sintered materials and filter elements. (Melt filter, sintered mesh filter, filter disc, filter and other industrial filters such as air filter, water filter, oil filter), filter and filter system assembly.
Products are widely used in petroleum, chemical, chemical fiber, aviation, aerospace, nuclear industry, pharmaceutical,
metallurgy, electric power, water treatment, food and beverage, coal chemical and other industries.
