Specifications:
High Tensile Steel Wire As Per the following specs
Bright Plain High Tensile Steel Wire of 7mm Diameter QTY 250 Metric Tons
1) Steel required must be bright plain - high tensile steel wire 7mm diameter and will be used in manufacturing prestressed concrete poles for medium voltage networks.
2) The steel should conform in all respects with the requirements of the latest edition of BS. 5896 or Chinese specifications [prestressed wire 7.00-1570-WLR-P-GB/T 5223/2002] or equivalent.
3) The nominal tensile strength of the steel should be (1570 N/mm2).
4) The steel should be of “Low relaxation “quality, and the wire is pre-straightened and will run out straight form the coil when used at site.
5) No joint is allowed in the wire which should be one piece in the coil.
6) Steel should be supplied in large diameter coils of (1.8 -2.4) m.
7) The weight of Each coil should be approximately 1000 kgs.
8) Good attention should be paid to the packing of each coil to ensure good protection to the steel during loading, shipping, unloading, transportation, and storing at the site of the purchaser. For that, every coil should be tightly wrapped by proper and secure seaworthy packing.
9) Each coil should have a separate label made of steel sheet with a reasonable size. This label should contain the following information: will be given upon production
10) The price should be valid for at least Two Month and must be based on steel NET weight.
Please quote for the following wholesale product requirement -
Product Name: Sprinkler Red Galvanized Fire Pipes
Specifications:
AS1074 Fire Sprinkler Pipe, Both Red Oxide And Gal In Sizes As Shown Below. 25mm x 6.5 Meters 32mm x 6.5 Meters, 40mm x 6.5 MeEters, 50mm x 6.5 Meters, 65mm x 6.5 Meters, 80mm x 6.5 Meters 100 mm
Buyer is interested to receive quotations for the following RFQ -
Product: Steel Billets
Specifications:
Billet 130×130×12m
Physical parameters: Parameters Value
Rhombodity 3% Max
Diagonal difference = 10mm
Corner radius 4 mm Max
Straightness Camber 5mm/meter
Angular Twist Not more than 1 degree per meter and not more than 6 Degree over 12 meter length.
Cutting Both ends will be Shear Cut
Identification At the end of each billet cast number and size will be Stamped or hand written
Surface The defects like longitudinal cracks, transverse cracks, scab and thick scale, slag patches, surface blowholes etc. will be within acceptable range.
Specifications:
High Tensile Steel Wire as per the following specs
Bright Plain High Tensile Steel Wire of 7mm Diameter QTY 250 Metric Tons
1) Steel required must be bright plain - high tensile steel wire 7mm diameter and will be used in manufacturing prestressed concrete poles for medium voltage networks.
2) The steel should conform in all respects with the requirements of the latest edition of BS. 5896 or Chinese specifications [prestressed wire 7.00-1570-WLR-P-GB/T 5223/2002] or equivalent.
3) The nominal tensile strength of the steel should be (1570 N/mm2).
4) The steel should be of “Low relaxation “quality, and the wire is pre-straightened and will run out straight form the coil when used at site.
5) No joint is allowed in the wire which should be one piece in the coil.
6) Steel should be supplied in large diameter coils of (1.8 -2.4) m.
7) The weight of Each coil should be approximately 1000 kgs.
8) Good attention should be paid to the packing of each coil to ensure good protection to the steel during loading, shipping, unloading, transportation, and storing at the site of the purchaser. For that, every coil should be tightly wrapped by proper and secure seaworthy packing.
9) Each coil should have a separate label made of steel sheet with a reasonable size. This label should contain the following information: will be given upon production
10) The price should be valid for at least Two Month and must be based on steel NET weight.
Services: Provision of design, engineering, project management, fabrication, construction & procurement for the oil & gas industries Buyer: Steel products, PPE equipments, perimeter security
