DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
SECrosslink-3010 single component, low temperature rapid curing, low surface resistance, mainly used in circuit board packaging, composite material shell, plastic shell, aircraft body electromagnetic wave shielding, suitable for jet and screen printing process.
Brand SECrosslink Type SECrosslink-3010
Product name EMI Electrically Conductive coating Appearance Silver gray
Resin types Acrylate Application Electromagnetic wave shield of circuit board package, composite shell, plastic shell, aircraft body
Adhesive force excellent Volume resistivity 75 DB
Advanced Reflective Insulating Coating
Reflective insulating coating is made of imported and domestic reflection, insulation raw materials, TAO, etc., self-crosslinking polymer. After the film is formed into a film, it has the characteristics of high heat-reflecting heat insulation, weather resistance, and excellent stain resistance. It can effectively reduce the surface temperature of the wall and is suitable for all kinds of building energy-saving projects. It is a new energy-saving waterproof and heat-insulating material that integrates anti-heat, radiation and barrier functions.
The coating can reflect more than 85% of solar radiation and near-infrared light in the range of 400-2500nm (the solar reflectivity is 0.85), effectively preventing the heat accumulation of sunlight. At the same time, a thermal resistance material with extremely low thermal conductivity is added to the coating to effectively block the transfer of thermal energy.
PU-3018A is a protective resin made of water borne polyurethane dispersions, using high performance additives and advanced processing technology. The waterborne peelable coating made of this resin has bright color, and fine particle size, coated on the surface of automobiles, furniture, electrical appliances and other objects as a protective coating, with good protection, can form a continuous, uniform, strong protective coating on the surface of complex shapes, can isolate the erosion medium, protect the surface of the substrate not easy to be worn, abrased, scratched, meanwhile, moisture-proof, rust-proof, corrosion â??proof, improve the commodity value of coated products. Upon completion of the protection period, the film can be conveniently removed to restore the original appearance of the object.
Physical Property
ModelPU-3018ACompositionPolyurethane organosilicon copolymerAppearanceMilky liquid with blue shadeSolid content35�±2%PH7.1-8.0IonicityAnionViscosity (Brookfield 25â??)50-160mpa.s
Performance Features
High peeling strength, not easy to break
High strength, good water resistance
Excellent low temperature resistance, weather resistance, air permeability and moisture resistance, and universality of different substrates
Applications
All kinds of metal surface, for example, temporary protection of products such as automobiles and stainless steel appliances
Temporary protection of all kinds of glass products
Temporary protection of all kinds of plastic products
Can be used as temporary protection for coating, ink coating
Can be used as temporary protection for other products
Application Guide
Can be directly painted on the surface of the construction surface, or add the right amount of water after dilution
Can be added talc, silica and other inorganic split materials
Can also add resin-free pigment paste to do color temporary protection coating
The peelable film dry completely, when it needs to be removed, please tear out a long mouth along the edge of the film, and then slowly peel the film from the coated surface with a force of about 4-5kg
Packaging and Storage Condition
50KG, 120KG, 200KG plastic drum;
Stored in a 100% light â??proof sealed container;
Stored in a cool and dry place indoor at 5-30â??;
Under high temperature or exposure, the shelf life will be significantly shortened;
Shelf life is 12 months from the date of production under condition that the drum is not opened.
Special Tips
This material is complied according to our existing technology and experience, the technical advice provided is sincere, but it is not guaranteed to be used in all samples and formulations, all the data are for users reference only.
I would like to introduce our company to POWLAND POWDER COATING , which is ISO 14001 9001 certified. Our company specializes in manufacturing high temperature dye and competitive prices
We provide all the colors they need, light, heavy, shiny and wrinkled
company's policy
We are interested in providing benefits, quality, customer satisfaction and the necessary standards in safety issues for cadres and workers in the sectors that provide services, so that you enjoy our work that aims to reach the level of the most important companies in Turkey and participate constantly in developing the economic aspect of the country. We take into account all changes and productivity in the advanced business world, mobility, quality, original ideas, and expected perspectives, taking into account through long-term cooperation and action, and our vision is to make our company a leading and pioneering enterprise in the dyeing sector. Our mission is to focus on customers, define market requirements and needs, develop marketing strategies and create new maps and to be dynamic, and that everyone is respected, stable and strong, and that they are an honest, caring and trustworthy institution, and not to assign and compensate for the quality of services and facilities in any way. Our values are customer focus, complete trust, honesty, tolerance, continuous development, and quality leadership.
We have great interest in working with you, and we strive to obtain a prompt response from you in order to arrange a visit and submit our offers. Thank you.
Theaoson zinc coating spray is composed of aerosol can, aerosol valve, paint liquid and propellant. This product uses bright silver powder imported from Germany. The color of the paint film produced after use has the same high-gloss galvanized color as the galvanized parts, it has the same color as the galvanized color that fades with the exposure time, so that there is no color difference in the repaired part coated on the galvanized part.
High quality lightweight polyester putty for car repairs – latest technology in putties.
- Creamy texture.
- Very low density.
- Extremely easy to mixing and apply.
- Exceptional sanding quality.
Color - Light Blue.
Gloss Grade – Matt.
Density – 1,00 kg/l.