Sulfate Resistant Portland Cement SRPC also named Sulfate Resistant Cement SRC is one of hydraulic binding materials can resistance to sulfate ion attack
Type High Sulfate Resistant Cement PHSR and Moderate Sulfate Resistant Cement PMSR
Grade 325 425
Application
To make concrete of sulfate resistance marine concrete maritime works
To make cement boards precast cement products cement pipes precast concrete pile shop fabricated members
Sea water attack resistance projects for example sea wall dam mariculture project sea water desalination project oceanarium etc
Chemical resistant engineering concrete
To make sulfate resistant concrete engineering of harbor water conservancy underground tunnel drainage pipe diversion works road and bridge foundation etc
RPC-WELD PVC solvent cements have passed the following tests performed according to ASTM Standard D2564
Test Pressure
2 hour Hydrostatic Burst Test 400 psi
2 Hour Lap Shear Test 250 psi
16 Hour Lap Shear Test 500 psi
72 Hour Lap Shear Test 900 psi
DIRECTIONS:
Keep container close when not in use
Set time is the time required before joint can safely be handled.
Cure time is the time required before joint can be pressure tested
1. Cut pipe square with saw or hand cutter. Remove all burrs.
2. Check dry fit of pipe and fitting. Pipe should easily go to way into fitting. If pipe bottoms into fitting
it should be very snug.
3. Pipe and Fitting should be free of dirt, grease and other foreign materials. If necessary clean pipe and
fitting using RPC-WELD Pipe Cleaner. Primer is highly recommended for 3 and larger diameter installation.
Apply liberal coat. Primer will start softening surface of pipe and fitting thus ensuring superior joint.
4. Use applicator supplied with the can or suitable applicator at least the size of the pipe diameter
5. Apply liberal coat of cement to the pipe (equal to depth of fitting) and adequate coat inside of fitting.
Make sure there is no uncoated surface. Avoid puddling of cement, it may weaken the joint.
6. Immediately insert pipe into fitting with twisting motion. Cement should be wet. If it has dried recoat both parts.
Use sufficient force to ensure pipe bottoms into fitting.
7. Hold joint together for 30-40 seconds to make sure pipe is not pushed out longer time if temperature is low
and for larger pipes.
8. Allow 15 minutes set time before handling the assembly and 2 hours cure time if temperature is below 60 F.
Longer cure time may be required for larger pipe and /or if temperature is below 60 F.
Do not test with compressed air.
DIRECTIONS FOR USE:
- Shake well before using.
- Keep container closed when not in use.
- Set time is the time required before joint can safely be handled.
- Cure time is the time required before joint can be pressure tested.
1. Cut pipe square with saw or hand cutter. Remove all burrs.
2. Check dry fit of pipe and fitting. Pipe should easily go A1/A3 to A1/A2 way into fitting. If pipe bottoms into fitting it should be very snug.
3. Pipe and Fitting should be free of dirt, grease and other foreign materials. If necessary clean pipe and fitting using RPC-WELD Pipe Cleaner. Primer is highly recommended for 3 and larger diameter installation. Apply liberal coat. Primer will start softening surface of pipe and fitting thus ensuring superior joint.
4. Use applicator supplied with the can or suitable applicator at least A1/A2 the size of the pipe diameter.
5. Apply liberal coat of cement to the pipe (equal to depth of fitting) and adequate coat inside of fitting. Make sure there is no uncoated surface. Avoid puddling of cement, it may weaken the joint.
6. Immediately insert pipe into fitting with twisting motion. Cement should be wet. If it has dried recoat both parts. Use sufficient force to ensure pipe bottoms into fitting.
7. Hold joint together for 30-40 seconds to make sure pipe is not pushed out longer time if temperature is low and for larger pipes.
8. Allow 15 minutes set time before handling the assembly and 2 hours cure time if temperature is below 16 C or 60 F Longer cure time may be required for larger pipe and /or temperature is below 16 C or 60 F.
DIRECTIONS FOR USE:
Shake well before using.
Keep container closed when not in use.
Set time is the time required before joint can safely be handled.
Cure time is the time required before joint can be pressure tested.
1. Cut pipe square with saw or hand cutter. Remove all burrs.
2. Check dry fit of pipe and fitting. Pipe should easily go way into fitting. If pipe bottoms into fitting
it should be very snug.
3. Pipe and Fitting should be free of dirt, grease and other foreign materials. If necessary clean pipe and
fitting using RPC-WELD Pipe Cleaner. Primer is highly recommended for 3 and larger diameter installation.
Apply liberal coat. Primer will start softening surface of pipe and fitting thus ensuring superior joint.
4. Use applicator supplied with the can or suitable applicator at least the size of the pipe diameter
5. Apply liberal coat of cement to the pipe (equal to depth of fitting) and adequate coat inside of fitting.
Make sure there is no uncoated surface. Avoid puddling of cement, it may weaken the joint.
6. Immediately insert pipe into fitting with twisting motion. Cement should be wet. If it has dried recoat both parts.
Use sufficient force to ensure pipe bottoms into fitting.
7. Hold joint together for 30-40 seconds to make sure pipe is not pushed out longer time if temperature is low
and for larger pipes.
8. Allow 15 minutes set time before handling the assembly and 2 hours cure time if temperature is below 16 C or
60 F Longer cure time may be required for larger pipe and /or temperature is below 16 C or 6
DESCRIPTION: King PVC Solvent is a clear, medium bodied, high strength, fast setting PVC solvent cement for all classes and schedule. This solvent cement is manufactured in the India.
APPLICATION: King PVC Solvent is for use on PVC pipes and fittings. This cement may be used for upto 4â??â?? pipes and fittings with interference fit for potable water, irrigation, drain, waste, vent, sewer and conduit applications.
PROPERTIES AND SPECIFICATIONS:
Color: Clear
Appearance: Liquid
Set Time: Fast
Cure Time: Consult ASTM schedule
Exceeds: ASTM D2564 specification
Shelf Life: 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units / case Units/ master
59 ml 24 192
118 ml 24 144
237 ml 24 96
473 ml 12 48
946 ml 6 24
DESCRIPTION : RPC-WELD PVC Solvent is a clear, heavy bodied, high strength, fast setting PVC solvent cement for all classes and schedule. This solvent cement is manufactured in the India.
APPLICATION : RPC-WELD PVC Solvent is for use on PVC pipes and fittings. This cement may be used for all grade pipes and fittings irrespective of diameter with interference fit for potable water, irrigation, drain, waste, vent, sewer and conduit applications.
PROPERTIES AND SPECIFICATIONS:
Color: Gray
Appearance: Liquid
Set Time: Fast
Cure Time: Consult ASTM schedule
Exceeds: ASTM D2564 specification
Shelf Life: 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units / case Units/ master
50 ml 24 192
100 ml 24 144
200 ml 24 96
250 ml 24 96
500 ml 12 48
1000 ml 6 24
DESCRIPTION: RPC-WELD PVC Solvent is a clear, heavy-bodied, high strength, fast setting PVC solvent cement for all classes and schedule. This Solvent cement is manufactured in the India.
APPLICATION: RPC-WELD PVC Solvent is for use on PVC pipes and fittings. This cement may be used for all grade pipes and fittings irrespective of diameter with interference fit for potable water, irrigation, drain, waste, vent, sewer and conduit applications.
PROPERTIES AND SPECIFICATIONS:
Color: Clear
Appearance: Liquid
Set Time: Fast
Cure Time: Consult ASTM schedule
Exceeds: ASTM D2564 specification
Shelf Life: 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units / case Units/ master
50 ml 24 192
100 ml 24 144
200 ml 24 96
250 ml 24 96
500 ml 12 48
1000 ml 6 24
DESCRIPTION : RPC-WELD PVC Solvent is a clear, heavy bodied, high strength, fast setting PVC solvent cement for all classes and schedule. This solvent cement is manufactured in the India.
APPLICATION: RPC-WELD PVC Solvent is for use on PVC pipes and fittings. This cement may be used for all grade pipes and fittings irrespective of diameter with interference fit for potable water, irrigation, drain, waste, vent, sewer and conduit applications.
PROPERTIES AND SPECIFICATIONS:
Color: Clear
Appearance: Liquid
Set Time: Fast
Cure Time: Consult ASTM schedule
Exceeds: ASTM D2564 specification
Shelf Life: 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units/Case Units/ master
50 ml 24 192
100 ml 24 144
200 ml 24 96
250 ml 24 96
500 ml 12 48
1000 ml 6 24
DESCRIPTION : RPC-WELD PVC Solvent is a clear, heavy bodied, high strength, fast setting PVC solvent cement for all classes and schedule. This solvent cement is manufactured in the India.
APPLICATION: RPC-WELD PVC Solvent is for use on PVC pipes and fittings. This cement may be used for all grade pipes and fittings irrespective of diameter with interference fit for potable water, irrigation, drain, waste, vent, sewer and conduit applications.
PROPERTIES AND SPECIFICATIONS:
Color: Clear
Appearance: Liquid
Set Time: Fast
Cure Time: Consult ASTM schedule
Exceeds: ASTM D2564 specification
Shelf Life: 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units / case Units/ master
59 ml 24 192
118 ml 24 144
237 ml 24 96
473 ml 12 48
946 ml 6 24
