Fabryka Narzdzi Glob Sp. Z O.O.

We are glad to propose 500 MT of stain less steel mill scale.
Mill scale is formed on the outer surfaces during by the hot rolling lamination of stainless-steel products.

At a visual inspection the material is a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in colour, but it also contains considerable alloying elements such as chromium and nickel.

The recovery ratio after melting in furnace for the most valuable alloy elements is:
- Ni: 3.5 - 4.5%
- Cr: 6-8%


From the chemical and physical analysis performed on the scrap, and according to the European environmental rules, the material has been classified as a special non dangerous waste, listed in green list. In particular the mill scale can be classified as follows:

Waste code: 10 02 10

The material is stored on cemented flooring, and it can be loaded loose in tipper trucks or containers.

Chemical analysis of the material is available on request.

Commodity: Dicalcium phosphate Feed Grade
Use
DCP is the feed preparation of raw materials, Animal right to supplement calcium needs. Coarse its products more applicable to the preparation hens, ducks feed, concentrate feed and premix.
Product Nature
Molecular Formula:CaHPO4·2H2O,Molecular weight:172.09,After drying with loose white powdery crystals or granules. Neutral products, the melting acid, water-soluble, hygroscopicity small, heated to 90 around gradually lose water of crystallization.

Product Features
The purity of the product, calcium and phosphorus ratio appropriate to ensure a higher degree of its biological effects. Phosphorus content greater than 18% of the products, due to a small amount of MCP, and its biological effects better.
This unique high-tech companies use technology to make our products crystallization, high purity and its harmful impurities significantly below standards:HG26362000
Drying process advanced products, products with low free water under the premise that the product does not lose crystallization of water, avoid the product in the drying process for the loss of water caused by crystallization of biological effects of the reduction.
Coarse particle DCP in the animals stay in the stomach longer and more conducive to the absorption of calcium phosphate, the product of Micro-particle DCP granulation from mechanical, without any chemical binder.

Specifications
Appearance white and gray powder/granule
Total P 18% min
Calcium 21% min 
F 0.18% max
As 30 ppm max
Pb 30 ppm max

Packing and Storage
Knitted bags lined polyethylene plastic bags double packaging, Weighing 25Kg/50KG/1000Kg. Transportation-and harsh rain. Stored in a cool, ventilated, dry place.

We are supplier and exporter of Hematite Powder.

Hematite Powder is a mineral, coloured black to steel. It is mined as a main of iron ore and used as a weighting agent in oil drilling. It is the mineral form of iron(III) oxide (Fe2O3). Fluids weighted with API Hematite Powder contain fewer solids by volume than, making higher mud fluids possible. API Grade Hematite Powder is applicable in all types of drilling fluids, including freshwater, seawater and oil-base muds. It is used as a density increasing product, used as a weighting agent and in the paint industry. Hematite is also a harder mineral than Barite so it is more resistant to particle size degradation.

High Density Hematite Powder API Grade -SG = 5.19 - 5.47 -Fe2O3 = 96.70% -Fe = 71.82% -SiO2 = 0.89% -Mesh Size (passing at 98%) = 325

Premium bleaching earth for moderate to hard-to-bleach oils. For soybean, sunflower, rapeseed, caster, palm, coconut oil edible oil. At BizWhite, we have a unique concoction of extensive research and process expertise, allowing us to manufacture highly efficient bleaching earth.

BizWhite Oil Boost offers edible oil refiners processing aids to produce clean, clear, quality oil. It features a large, highly active surface area well suited for the removal of colour bodies and impurities from edible oils.

BLEACHING
Good Bleaching in the refining process is essential to produce high-quality edible oil.

QUALITY
We are highly encouraged to achieve the highest quality standards of bleaching earth.

PROVEN PERFORMANCE
Efficient removal of chlorophyll, carotene, and other color bodies.
Fast filtration with long filtration cycles and less pressure build-up at cycle end.
Reduce free fatty acid rise and the associated risk of damaged oil.

GRADES
BizWhite Oil Boost - BW- 207
BizWhite Oil Boost - BW-108

Features Of Granulated Blast Furnace Slag (GBFS)

Granulated Blast Furnace Slag or GBFS is formed when Blast Furnace Slag or BFS is successively at a fast rate quenched from the furnace rather than left for cooling. It has a density of about 60% to 70% that of natural sand. This material has a much increased resistance to sulfate attack.

This eventually leads to better performance in countering acids of any type. In GBFS, no type of reaction related to alkali and silica occurs. Also the material provides a huge saving in connection to carbon dioxide emission which is an extra boon. What constitutes GBFS are its properties that consist of durability, appearance, higher ultimate strength than concrete which is made up of Portland cement and high sustainability level of the product made out of this material.

Product introduction:

Calcium is a silvery white metal that is harder and heavier than lithium, sodium, and potassium;

It melts at 815 C. The chemical nature of metallic calcium is very active. In the air, calcium is quickly oxidized and masked with an oxide film. When heated, calcium will burn and emit a beautiful glow of brick red. Calcium and cold water have a slower effect, and intense chemical reactions occur in hot water to release hydrogen (lithium, sodium, and potassium can cause intense chemical reactions even in cold water). Calcium is also easily combined with halogens,

sulfur, nitrogen, and the like.



1,product name:calcium metal

2,Shape :powder, lump and granulates

3,CAS:7440-70-2

4,Density:1.54g/cm

5,Melting point:850C

6,Boiling point:1440 C(lit.)

7,Application:Wheel keel



Product use:

At present, in the steel industry, the main use of metal calcium is to process into metal calcium particles, and then to make calcium iron wire or pure calcium wire, and finally used for steel refining outside the furnace, its role is to desulfurization, deoxidation, increase the fluidity of molten steel. Promote the rapid rise of inclusions in molten steel, generally used in the production of high-quality steel; as a dehydrating agent to produce anhydrous alcohol; in the petroleum industry, as a desulfurizing agent, in the metallurgical industry, it is used to deoxidize or

desulfurize . However, calcium compounds have a very wide range of uses, especially in the construction industry.

THF is an important organic synthetic raw material and a solvent with excellent performance. It is especially suitable for dissolving PVC, polyvinylidene chloride and butyl aniline. It is widely used as a solvent for surface coatings, anticorrosive coatings, printing inks, tape and film coatings, and used in combination. As a reaction solvent, the thickness and brightness of the aluminum layer can be arbitrarily controlled when used in the aluminum electroplating solution. THF itself can be polycondensed (ring-opening and repolymerization initiated by cations) into polytetramethylene ether glycol (PTMEG), also known as tetrahydrofuran homopolyether. PTMEG and toluene diisocyanate (TDI) are made into special rubbers with abrasion resistance, oil resistance, good low temperature performance and high strength; with dimethyl terephthalate and 1,4-butanediol to make block polyether polyester elastic Material.

Our Bath Material goes beyond primary aluminum production, finding applications in aluminum scrap recycling and various industrial processes. Whether you're involved in glass, enamel, ceramics manufacturing, or other industries, our Bath Material proves to be a versatile and valuable resource.

Explore the high-quality Bath Material solutions offered by Gremlog , providing excellence in electrolyte materials for diverse industrial application

Discover the versatility of our cryolite offerings, available in a range of sizes tailored to meet diverse industry requirements. Our commitment to precision and customization ensures that our high-quality cryolite aligns seamlessly with the specific needs of your aluminum smelting processes, providing optimal performance and efficiency.Choose from our meticulously graded sizes, including :

0-5 mm;
5-20 mm;
20-40 mm;
0-40 mm;
5-40 mm;