We are pleased to offer you Hot Briquetted Iron Chips with Libyan origin. Below is the Chemical composition:
CHEMICAL COMPOSITION:
Iron (Fe) - 86% min
Alumina (Al2O3) - 2.5 max
Silica (SiO2) - 3.5 max
Phosphorus (P) - 0.08 max
Sulphur (S) - 0.08 max
PHYSICAL SIZE (On Natural Basis)
6.5mm - 14mm: 70% min
14mm - 16mm: 20% max
16mm - 18mm: 10% max
Analysis report is available upon request.
Please let us know any interest.
Cold Briquetted Iron (CBI) is defined as DRI which has been molded at a temperature less than 650 �°C or with a density of less than 5000 kg/m3. Due to the raw material sharp shortage for steelmaking in many countries worldwide, a need arises to find a substitute material to replace the rare pig iron and expensive steel scraps that were used by steelmaking plants.
1- More density and less porosity
The apparent density of CBI is about 8.3 grams per cubic centimeter and the density of DRI is about 2.3 grams per cubic centimeter. On the other hand, the volumetric porosity of these two products is about 30 and 50%, respectively. These two factors reduce the environmental reactivity of CBIC and its lower transportation costs.
2- Less fine
The wear resistance and higher mechanical strength of CBI compared to sponge iron causes less softening to occur during the handling of the product, and as a result, both the economic value of the product is prevented and the charge losses of the product in the steelmaking furnace are prevented. is significantly reduced.
3- Easier to store and carry
Due to the lower reactivity of CBI compared to DRI, the loss of metal grade of the product during storage and transportation is significantly reduced, which will reduce the amount of economic value loss of the product from the time of production to the time of use in the steelmaking furnace. On the other hand, sea transportation of CBI leads to a reduction in transportation costs compared to DRI due to the absence of the need to apply neutral gas to prevent product activation.
4- More thermal and electrical conductivity
The thermal and electrical conductivity of CBI is about 2 times that of DRI. This higher conductivity of CBI improves the distribution of heat created in the steelmaking furnace and, as a result, accelerates the melting process of iron materials. This will mean reducing the melting time of the steelmaking process and improving the production capacity of the steelmaking unit.
5- Carbon adjustment
The presence of carbon in steelmaking furnaces is necessary in order to provide carbon for the final steel product, prevent excessive losses of iron, and also regulate the physical and chemical conditions of the slag. Usually, induction furnaces require low-carbon iron materials, but in electric arc furnaces, high-carbon iron materials are more attractive. The unique feature of CBI product is the ability to adjust its carbon content in the range of 0.5 to 4% by weight and based on the needs of customers.
Mill scale, is formed on the outer surfaces of plates, sheets or profiles when they are being produced by rolling hot iron or steel billets in rolling or steel mills.
It looks like a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in color.
Being produced during the reheating, conditioning and hot rolling operation for the production of steel articles, the mill scale initially adheres to the steel surface and protects it from atmospheric corrosion, provided no break occurs in this coating.
From the chemical and physical analysis performed on the scrap, and according to the european environmental rules, the material has been classified as a special non dangerous waste, listed in green list
In particular the mill scale can be classified as follows:
Einecs (european commission no.): 266-007-8
Waste code: 10 02 10
Basel code: b 12 30
Hs code: 2619.00
We are glad to propose 500 MT of stain less steel mill scale.
Mill scale is formed on the outer surfaces during by the hot rolling lamination of stainless-steel products.
At a visual inspection the material is a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in colour, but it also contains considerable alloying elements such as chromium and nickel.
The recovery ratio after melting in furnace for the most valuable alloy elements is:
- Ni: 3.5 - 4.5%
- Cr: 6-8%
From the chemical and physical analysis performed on the scrap, and according to the European environmental rules, the material has been classified as a special non dangerous waste, listed in green list. In particular the mill scale can be classified as follows:
Waste code: 10 02 10
The material is stored on cemented flooring, and it can be loaded loose in tipper trucks or containers.
Chemical analysis of the material is available on request.
Ground Granulated Blast Furnace Slag (GGBFS) is a by-product from the manufacture of Iron and a high-performance substitute to traditional cement that will rise the technical presentation of your application, improve its appearance and minimize its environmental impact. GGBS is used in combination with Portland cement to produce superior longer-lasting concrete. GGBS will improve performance in any situation, from housing to civil engineering applications.
GGBFS also improves the concrete toughness, reduces preservation and repair costs, progresses workability and compression features, extensions compressive and flexural strengths, decreases cement and water consumption, advances concrete grading and also improves impermeability and water resistance.
Arij Global Trading LLC is a professional Ground Granulated Blast Furnace Slag supplier. We are a global company operating in the fields of the mineral industry, trade, and logistics. Reliable and responsible entrepreneurship, combined with flexibility and innovative logistics solution, plus our motivated and skilled employees, our core proficiencies and efficient work processes, we continuously achieve an above-average value contribution.
GGBFS
Ground Granulated Blast Furnace Slag (GGBFS) is gained by grounding the Granulated Blast Furnace Slag into the desired fineness. This product is usually intended to be used in concrete either as an element of composite cement such as Blast furnace Cement/High Slag Blast Furnace Cement or as a straight addition to the concrete mix by the concrete producer.
GBFS
Granulated Blast Furnace Slag GBFS can be used like sand as an additional aggregate for building materials. Granulated Blast Furnace Slag is obtained by quickly chilling (quenching) the molten ash from the furnace with the help of water. Throughout this procedure, the slag becomes fragmented and changed into amorphous granules (glass).
