A. PRODUCT DESCRIPTION:
These are Paint thinners. These are designed to improve the flow of a range of MARLAC Paint products. Can also be used as a cleaner for metal cleaning, pumps and tools before and after applications.
B. TYPICAL USE:
Suitable as Thinner for :
1)Alkyd and Oil based Paints
2)Epoxy Paints
3)Polyurethane paints
4)All types of Stoving and Air drying paints
5)Cleaning thinner
C. COLOUR:
Colourless clear liquid.
D. PRODUCT DATA:
(a) Boiling Range : Calculated
(b) Flash Point : As Per Std
(c) Density : 0.85 + 0.1
The data may slightly vary depending on the properties of the RM Solvents used.
E. PACKAGING:
5 or 20 Lt Drum
F. STORAGE:
The material must be stored as per the regulations. Keep the containers in Dry, Cool, Well Ventilated
space and away from the source of Heat and ignition. Containers must be kept tightly closed. Handle with care.
G. SHELF LIFE:
Minimum 12 months, provided stored properly.
H. HEALTH AND SAFETY:
Please follow the precautionary advices on the container. Use under well ventilated conditions. Do not
inhale spray mist. Avoid Skin contact. Spillage on the skin should immediately be removed with
suitable cleanser, soap and water. Eyes should be well flushed with water and medical attention sought
immediately.
I. DISCLAIMER:
The information in this document is given to the best of MIPPLâ??s knowledge, based on the laboratory
testing and practical knowledge. MIPPL reserves the right to revise the data without further notice.
Users should always consult MIPPL for specific guidance on the general suitability of this product for their needs and specific practices.
HI - Performance Syn. Enamel Paint
Superior Durability Color Pigment System
Easy To Apply By Brush , Roller And Spray
PRODUCT PARAMETERS
1. Type : Single Pack
2. Composite : Modified Oil Based Resin with Finest Bright
Pigments, Hydrocarbon solvent and addives
3. Use Recommended Thinner to make
Applicaon Viscosity
4. Applicaon Tools : Brushing, Spraying or
Roller
5. Flash off = 30 Minutes
6. Drying Time :
Surface Dry : 4 Hours
Hard Dry : Overnight
7. Curing Time : 72 hours
8. Over coang Interval : MIN : Overnight
MAX : 5 Days
9. Color : Assorted Shades
. Finish :
10 Smooth Finish
11 Thinner / Cleaner KISOMIN THINNER
12. Shelf Life: Up to 12 Months as long as the sealed containers
are kept under cover in a dry place under normal
temperature.
SCOPE
USES
Kisomin durable synthec enamel are long lasng & solvent based
paint used for wide range of surface.
Recommended as a decorave finish coat & can be applied on
surfaces like Metal, Cement Brickwork, Asbestos Grills and Wooden
surfaces like doors, Windows, Cabinets & wide range of furniture
PERFORMANCE PROPERTY
Chemical Resistance
A Exposures Splash & Mild Fumes/Outdoor
Spillage Resistance
cid + +
Alkalis + +
Solvent NA NA
Salt ++ ++
Water +++ +++
Flexibility +++
Adhesion +++
Excellent : +++
Very Good : ++
Good : +
SURFACE PREPARATION
APPLICATION
BRUSH
CONVENTIONAL SPRAY
NOTES :
HEALTH & SAFETY
Steel : Sand the surface with coarse Sand / water paper according to the type of surfaces to remove rust, dust & other foreign parcles. System of
Coang should be selected depending upon the type of substrate. Wipe to clean the surface. Apply single coat primer & allow to dry. Re sand the
surface with Sand paper & wipe to clean. Apply 2nd Coat of primer & allow drying for overnight. Before applicaon of paint, thin down to achieve
desired viscosity & filter through white cloth. Apply Kisomin Paint to finish.
Sr the base thoroughly and then mix to uniform consistency.
Apply without thinning
Add Kisomin thinner to adjust viscosity depending on spray condion. Use any standard equipment at an atomizing pressure of 3.5-4.5 kg/cm�².
1. Use off the mixed paint .
2. Do not apply when temperature falls below 10 C or rises above 50�°c and when relave humidity rises above 90%. Do not apply during rain, fog or mist
3. Brushes and spray equipment should be cleaned with Thinner,
4. Special care to be taken to close immediately the partly used Diluted Material.
Please refer to the separate Material Safety Data Sheet available with detailed information
* Dual Advantage Of Stoving As Well As Air Drying Curing Schedules.
* Color Stability
* Both Solid As Well As Metallic Shades.
* Excellent Adhession & Flexibility With Good Hardness
* Ideal For Areas Exposed To High Temprature .
* Good Adhession On Mild Steel , Galvanized Steel And Aluminium Surfaces.
Contain Epoxy For Corrosion Protection And Reinforcement.
Overcoatable By A Wide Range Of Topcoats.
Stoving Primer And Topcoats
Heat Resistant Paint based on High Heat Resistant Epoxy resin with excellent anticorrosive and Heat Resistant Pigments, suitable for muffler inside coating.
Single Pack Heat Resistance Aluminium Paint Based On Silicone Resin.
Hr Aluminium Paint Film With Stand Up To 250 C.
It Gives Silver Like Finish And Brilliant Lusture To The Surface .
Good Water And Heat Resistance
High Quality Heat Resistance Paint Based On Pure Silicone Resin And Modified Resin
Available Shades In Metallic And Solid Version
Excellent Heat And Corrosion Resistance
Wet-on-wet application with 3 minutes flash off time.
* Single baking at 130 C for 25 min. High productivity & Low production cost.
* Recommended for welded areas as the composite system at 40-60 (Primer + Topcoat) gives minimum Salt Spray life of 240 Hrs.
