Usage
Mainly used for maintaining temperature of molten aluminum alloys, suitable for all the crafting processes, such as pre-aluminum casting degassing, alloy preparation, uniform structure and temperature regulation and so on.
â?¢ Energy source can be electricity and gas.
Equipment Features
â?¢Higher-quality molten aluminum can be obtained. Molten aluminum temperature accuracy, composition uniformity and less hydrogen content can be guaranteed.
Flexible production organization. The crucible can be replaced at any time for production of different types of alloys, without contaminating the molten aluminum.
Low burning loss of aluminum. The aluminum in the crucible is heated with heat conduction of the crucible, without local high temperature, reducing oxidizing loss and high-temperature volatilization, lowering the burning loss of aluminum to a level below 1.2%.
The furnace floor is molded by monolithic casting with a casting material. Moreover, at the bottom of the furnace is a leakage outlet, through which the molten aluminum can outflow once the crucible is broken, reducing the risk of damage to the furnace body.
The temperature of the furnace chamber and molten aluminum is controlled by series circuit, ensuring sufficient heating efficiency and preventing overheating of the furnace chamber.
The molten aluminum thermocouple protect tube is made from silicon nitride, which is well heat-conducting, resistant to corrosion by the molten aluminum, resistant to thermal and cold shocks and highly strong. The tube can be directly immersed in the molten aluminum to measure its temperature. It has a service life of more than 2 years.
Multiple safety protection modes are adopted, such as molten aluminum over-temperature alarm, furnace chamber over-temperature alarm and crucible leakage alarm and so on.
Usage
â?¢� Used for artificial aging treatment of castings. Divided into car bottom and chamber types.
� Technical Parameters
â?¢ Maximum heating temperature: 250â??
â?¢ Furnace temperature uniformity: â?¤�±5â??
â?¢ Temperature control precision: �±1
Usage
 Used for artificial aging treatment of castings. Divided into car bottom and chamber types.
 Technical Parameters
Maximum heating temperature: 250
Furnace temperature uniformity: ±5
Temperature control precision: ±1
Usage
Used for artificial aging treatment of castings. Divided into car bottom and chamber types.
Technical Parameters
Maximum heating temperature: 250
Furnace temperature uniformity: ±5
Temperature control precision: ±1
Usage
The equipment is mainly used for solution hardening and artificial aging heat treatment of aluminum alloy workpieces and the annealing heat treatment of aluminum alloys.
Used for treatment of aluminum alloy T4, T5, T6, T7 and T8.
Up to standard!
The heat treatment of the aluminum alloy materials conforming to the US military standard SAE AMS 2772E-2008
The heat treatment of the casting aluminum alloys conforming to the Chinese aviation standard HB5446-90
The vertical aluminum solution-hardening furnace, also known as drop-bottom aluminum solution-hardening furnace, is a heating furnace for periodic heat treatment, used for production of ultrahigh-quality workpieces in the war, aerospace, automobile manufacturing and high-voltage electrical equipment industries.
Small batch, high qualitythe best choice for solution treatment of aluminum!!
Three performance guarantee parameters:
 Furnace temperature uniformity: ±3
Temperature control precision: ±1
 Workpiece transfer time: 6-15s
Â
Equipment Features
A patented self-locking mechanism is adopted for the furnace door, ensuring that the furnace door will not descend by itself under any circumstances.
 There is a flexible sealing connection between the furnace door and the furnace body; the furnace door is pneumatically compacted, ensuring the synchronous sealing performance of the whole sealing surface.
 Each mechanical action is equipped with a perfect self-locking function, ensuring operation reliability and safety. Especially, there is a well-designed logical relation and reliable hardware-software logic interlocking circuit among the heating system, fan operation system, furnace door switch system, charging basket lifting system, water tank movement system and mixing system. They can keep the equipment and thermal treatment device safe in case a sequence error is caused by manual operation or a failure occurs in an action process during automatic operations.
 High furnace temperature uniformity. A large-flow and high-air-pressure heat-resisting fan is adopted, able to generate enough recirculating air quantity and pressure; the super-large furnace consists of multiple temperature control zones including one main zone, ensuring that temperature rises synchronously in all of the temperature control zones; the all-fiber furnace lining minimizes heat loss, ensuring that the furnace chamber temperature gradient is within a certain range.
High furnace temperature control accuracy. Multiplex control maximally ensures that the furnace chamber does not overheat, thus protecting workpieces from being softened and over-burnt.
Heating energy sources: natural gas, liquefied petroleum gas (LPG).
An imported famous-brand automatic burner or gas burner is adopted, ensuring high heating performance, low noise and zero-discharge of fume, meeting the environmental protection requirements.
After heating, the hot furnace gas is blown back to the upper mouth of the crucible through the flue; or preheated the combustion air from the flue heater ex-changer to improve the heating efficiency and reduce fuel consumption.
Multiple safety protection modes are adopted, such as gas under-pressure, assisted gas under-pressure, flameout alarm and so on.
Melting rate in a cold furnace: 3.5h
Melting rate in a heated furnace: 2h
The most widely used high-efficiency filtration system
Equipment Introduction
- The CFF Filtration Box (CFB) is widely used for molten aluminum filtration in the aluminum casting process to prevent the particulate impurities in molten aluminum from entering the casting blank and affecting the quality of aluminum products.
-According to the quality requirements of castings, the volume of molten aluminum, the total volume of filtered aluminum, and the cleanliness of the aluminum itself, the correct selection of the type of filter box and the specifications of the foam filter plate help to achieve satisfactory filtration results.
Main parameters of the CFB filtration box
- Maximum temperature of molten aluminum: 750°C
- Shell surface temperature: 70°C
-Lining life: 12 months
Common specifications of CFB filtration box
Filtration Box Type Code Filtration Board Size inch Flow Range
t/h Remarks
Single-stage filtration box CFB1-12 12 2-5 Â
A single filtration board is placed in the filtration box to filter out more than 85% of the inclusions with a particle size 8�¼m
CFB1-15 15 4-10
CFB1-17 17 8-15
CFB1-20 20 12-20
CFB1-23 23 16-25
Horizontal two-stage filtration box CFB2-12/12 12/12 2-5 Two-stage filtration boards with different pore sizes from large to small are placed in the filtration box horizontally or vertically to filter out more than 95% of the inclusions with a particle size 8�¼m
CFB2-15/15 15/15 4-10
CFB2-17/17 17/17 8-15
CFB2-20/20 20/20 12-20
CFB2-23/23 23/23 16-25
Vertical two-stage filtration box CFB2-15/12 5/12 2-5
CFB2-17/15 17/15 4-10
CFB2-20/17 20/17 8-15
CFB2-23/20 23/20 12-20
Two-channel filtration box CFB-12/12 12/12 2-52 Two channels in the filtration box for parallel arrangement of filtration boards of the same pore size. Used for continuous filtration of molten aluminum, one for use while the other as backup; used for filtration of large-flow or high-viscosity molten aluminum. Both channels meet the flow requirements together.
CFB-15/15 15/15 4-102
CFB-17/17 17/17 8-152
CFB-20/20 20/20 12-202
CFB-23/23 23/23 16-252
Notes:Equipped with heating device as needed.
Focus-6500 butyl tapes has good performance in waterproofing and sealing, non-hardening, weather resistance, strong adhesion, adaptation and anti-aging .
Technical Data
Product Series FOCUS-6500 Series
Application Home Decoration Industry
Elongation 500%
Heat Resistance 90, no flowing within 2h
Low Temperature Flexibility 40, no crack on surface within 24h
Peel Strength 22N/cm
Tensile Strength 210KPa
Anti UV non-hardening and no cracks within in 2000h
Corrosivity Non-corrosive to galvanizedsheet, aluminum sheet and coppersheet
Advantages
Smooth and Delicate.
Excellent Adaptation.
Greene nvironmental protection.
Non-toxic tasteless.
Good performance in waterproofing and sealing.
Best quality with outstanding service life.
Applications
Focus-6500 butyl tapes are widely used in bathrooms, kitchen, home decorations, office areas and other home applications, for its good
waterproof/mildew proof /airtight and environmental property.
Adopting unique production technology, Focus- 6300 buytl tapes are mainly made of butyl rubber supplemented by other auxiliaries and fillers, with the superior high polymer materials. With its strong adhesion property and air-tight
property, our waterproof sealing butyl tapes are environmental and solvent-free. Main Specification (Customized demand sare acceptable.)
6mm*8m
8mm*6m
10mm*4.57m
Main Color - black
Technical Data
Product Series FOCUS-6300 Series
Application Automotive Industry
Elongation 500%
Heat Resistance 90, no flowing within 2h
Low Temperature Flexibility 40, no crack on surface within 24h Peel Strength 23N/cm
Tensile Strength 230KPa
Anti UV non-hardening and no cracks within in 2000h
Corrosivity Non-corrosive to galvanized sheet, aluminum sheet and coppersheet.
Advantages
Strong adhesion, high tensile strength, excellent elasticity and extensibility. It can fully accommodate to the surface that it attached to
Excellent performance in non-corrosive, weather resistance and
adaptation.
Applications
Provide waterproof
protection to car doors waterproof membrane. Provide waterproof and
sealing protection to the battery of new energy
automobile.
Other waterproof applications on cars and new energy cars
