1. Description
YJS-620 is a two-component 1:1 Mix addition (platinum)cured RTV silicone rubber which cures at room temperature. Because of its considerable fluidity, it is recommended for the duplication of models with many undercuts. This stuff is really thin and easy to pour.
2. Features
*high chemical resistance to the aggressive components of some types of resin
*High resistance to laceration (this characteristic guarantees high resistance to wear and tear)
*High level of accuracy in reproducing very small particulars
*High dimensional stability over time and non-deformability
*Considerable resistance to high temperatures and to ageing
*Excellent non-stick effect
*Soft, stretchy, high tear resistance,
*Will not shrink in service
addition cure rtv2 liquid silicone for making mold
1. Description
YJS-620 is a two-component 1:1 Mix addition (platinum)cured RTV silicone rubber which cures at room temperature. Because of its considerable fluidity, it is recommended for the duplication of models with many undercuts. This stuff is really thin and easy to pour.
2. Features
*high chemical resistance to the aggressive components of some types of resin
*High resistance to laceration (this characteristic guarantees high resistance to wear and tear)
*High level of accuracy in reproducing very small particulars
*High dimensional stability over time and non-deformability
*Considerable resistance to high temperatures and to ageing
*Excellent non-stick effect
*Soft, stretchy, high tear resistance,
*Will not shrink in service
3. Technical datasheet
Typical general characteristics Inspection Method Value
Product data (Catalyzed A+B) YJS-620
Hardness Shore A 20±2
Mix Ratio A:B 1:1/10:1
Color / translucent
Pot life 25 °C (77F) 30-40mins
Curing time 25 °C (77F) 3-4 hours
Mixed viscosity mPa.s 5000±1000
Tear-strength kg/cm 20±2
Tensile-strength M.pa 4.0±1.0
Elongation % 500±50
Shrinkage % â?¤0.1%
3. Common uses
*Wax
*Urethane (polyurethane)
*Plaster Hydrocal, Hydrostone
*Polyester casting resin
*Low melt metals (mold life can be short)
*Cement, Concrete
*Epoxy
*Soap
*Chocolate
4.SHELF LIFE:
When stored at or below 32°C (89.6°F) in the original unopened containers, G-8 series Silicone have a usable life of 12 months.
1.Product Description
YJS-720 two components platinum cured silicone with 1:1 mixing ratio by weight. It is soft food grade silicone,
with 20 Shore A hardness, which is suitable used for moulding chocolate & icing sugar, candy, cakes, fondant.
2.Features:
A. Amazing fluidity and easy to operate
A. Platinum-based, food-grade silicone (environmental friendly, odorless and non-toxic)
B. Delicate design available
C. Mixing ration: 1:1, easy to mix
D. Easy de-molding
E. Excellent tension and tear strength
F. High performance in duplication
G. Shrinkage is almost zero (below 0.1)
H. Excellent resistance to weather, temperature, aging, acid and aging-proofing.
I. High resistance to high temperature and aging(resist -60 to 250)
J. Food safe
3.Technical Data
Typical general characteristics Inspection Method Value
Product data (Catalyzed A+B) YJS-720
Hardness Shore A 20±2
Mix Ratio A:B 1:1/10:1
Color / translucent
Pot life 25 °C (77F) 30-40mins
Curing time 25 °C (77F) 3-4 hours
Mixed viscosity mPa.s 5000±1000
Tear-strength kg/cm 20±2
Tensile-strength M.pa 4.0±1.0
Elongation % 500±50
Shrinkage % â?¤0.1%
4.Appearance:
Part A: a non-toxic and odorless liquid with translucent color and platinum inside
Part B: a non-toxic and odorless liquid with translucent color.
ATT: We can do any curing time as your requirements.
Notice:
What is the hardness should I choose
Normally 5~55 Shore A will be the best, but it also should according to your size and pattern design.
5.SHELF LIFE:
When stored at or below 32°C (89.6°F) in the original unopened containers, G-8 series Silicone have a usable life of 12 months.
Ferro silicon Specs: Si:75%min. and Si:72%min. C:0.2%max. S:0.02%max. P:0.04%max. Al:2.0%max.1.5%max.and 1.0%max .Commodity: Ferro Silicon Low Al Specs: Si:75%min. C:0.2%max. S:0.02%max. P:0.04%max.Al:0.1%max.0.3%max.and0.5%max. In 1mt plastic woven bags.
Ferro Silicon Ferro Silicon has a melting point of 1200�¯�¿�½?�?�°C to 1250�¯�¿�½?�?�°C with a boiling point of 2355�¯�¿�½?�?�°C and Ferro Silicon contains about 2% of calcium and alluminium. Ferro Silicon, as an additive to the production process of ferrous metals, will impart several desirable properties upon the resultant alloy. Some of the primary benefits of adding Ferro Silicon to an alloy is to improve the corrosion resistant properties of the new compound, as well as to add to the high temperature heat- resistance properties of the new alloy, for example, in the production of silicon steel for use in transformer cores.
FerroChrome is a kind of Ferro alloy which is formed by Ferro and Chrome,it is an important alloy addition in steel making. Ferrochrome (Fe Cr) is an alloy of chromium and containing between 50% and 70% chromium.
We are a leading supplier of electroplating chemicals, industrial polishing and welding consumables, water treatment, powder coating, fertilizers. We stock and carry an extensive range of ready to use chemicals. We deal with so many different chemicals and we would like you to contact us for more information about our different chemicals and products.
