Shenzhen Youber Technology Co., Ltd.

Conventional tanks (concrete or mild steel) are prone to aging, wear and corrosion.
Concrete can crack when exposed to erosion and natural disasters, leading to water
contamination and leakage â?? and usually canâ??t be repaired. MS rusts easily and its also
easy heat conductor.
FRP â?? Fiber Reinforced Polymer is a strong but light weight glass fiber reinforced plastic
composite used in the aerospace, automotive, marine and construction industries. It has
a high-strength to weight ratio, an extremely long lifespan, and easy to maintain as well as
heat resistant.
FRP sectional panel tanks provides all types of advantages which other liquid storage
methods doesnâ??t. These tanks are DURABLE, LEAK-FREE, COST-EFFECTIVE OVER LIFECYCLE as well as EASY TO INSTALL, RECONFIGURE AND RELOCATE. This is an ideal option
for a wide range of usage including potable water storage, food and factory production,
commercial mining, fire protection, industrial liquids, rainwater harvesting, seawater
storage, and any other kind of liquid and granular storages.

APPLICATION OF SK-HB K-SILICATE MORTAR :

* K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors.
It is also used for jointing chemical resisting stoneware pipes.
K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles.
The concrete surface needed protection should be dryed, clean and rough.
The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner.

When Bedding and Jointing Materials are the same.
On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints.
The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water.
Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic.
When Bedding and Jointing Materials are Different.
Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR
A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions.

PREPARATIONS OF MORTAR :
* Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan.

* Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar.

* In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared.

* The cement mortar will be used before it starts setting.

Super Heat Duty and High Alumina Fire Bricks arethe products made fromdifferent fractions of refractory grog, fire clays and calcinedbauxiteof high purity.Thedifferent fractionsof theserawmaterials aremixedin counter current mixers and plugged for obtaining homogeneous mixture. The mixtureobtained hence,is then pressed in high capacity presses to give the desired shape and size.These pressed shapes are fired in high temperature tunnel kiln at

1300 C and above. These bricks are manufactured as per IS: 6 and IS: 8

SPECIFICATION

Shape RECTANGULAR // CUSTOMISED
Brick/Block Color BROWN
For Use in Side Walls, Partition Walls, Roof, Floor
Brand GLM
Material CLAY AND ALUMINA / BAUXITE
Size 9 In. X 4 In. X 3 In.

High alumina brick for blast furnace;
Burned micro hole carbon-high alumina brick for blast furnace;
Normal high alumina brick for hot blast stove;
Low creep high alumina brick for hot blast stove;
High alumina brick for electric arc furnace roofs;
High alumina brick for steel ladle.


1. High Purity;

2. Small Impurities;

3. Low Thermal Capacity;

4. Low Thermal Conductivity;

5. High Strength;

6. Good Thermal Resistance;

7. Strong Anti-Corrosion.

Each kind of castable refractory material serves a different purpose. Here are some examples as to how people would use them for different applications.





Conventional Dense Refractories. These have a high concentration of alumina cement in their composition. Conventional dense refractory materials can handle temperatures that go as high as 1800 Fahrenheit. Applications such as boiler work require these kinds of materials.


Insulating Materials. Another kind of castable refractory is the insulating kind. They are lower density compared to the other types of castable refractory materials. They have low thermal conductivity as well. They are a good choice if you want something that will resist abrasion.


There is such a wide range of refractory materials that you can choose from for their applications. Castable refractory materials also vary, so we advise calling in for a consultation. Our knowledgeable staff will be happy to help out.

We offer premium quality acid resistant bricks, tiles and special shapes. We also offer customized Shapes and sizes as required by our customers.
We offer FIRECLAY and RED SHALE Type ACID RESISTANT BRICKS and TILES


sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 , IS 4860

A pure, buff white powder & crystal clear Solution of K-Silicate Mortar is generally used as a bedding Mortar in all types of Bricks, Tile & Stone Lining work. It is highly recommended where concentrated Sulphuric & Nitric Acids are used. It is most Identical Cement-Mortar for the Acid Proof & Refractory Brick Lining work into the RCC CHIMNEYS & TOWERS since it has an Unique nature of Acid & Heat Resistant. It may Resist Temperature upto 900C