Specifications:
High Tensile Steel Wire As Per the following specs
Bright Plain High Tensile Steel Wire of 7mm Diameter QTY 250 Metric Tons
1) Steel required must be bright plain - high tensile steel wire 7mm diameter and will be used in manufacturing prestressed concrete poles for medium voltage networks.
2) The steel should conform in all respects with the requirements of the latest edition of BS. 5896 or Chinese specifications [prestressed wire 7.00-1570-WLR-P-GB/T 5223/2002] or equivalent.
3) The nominal tensile strength of the steel should be (1570 N/mm2).
4) The steel should be of “Low relaxation “quality, and the wire is pre-straightened and will run out straight form the coil when used at site.
5) No joint is allowed in the wire which should be one piece in the coil.
6) Steel should be supplied in large diameter coils of (1.8 -2.4) m.
7) The weight of Each coil should be approximately 1000 kgs.
8) Good attention should be paid to the packing of each coil to ensure good protection to the steel during loading, shipping, unloading, transportation, and storing at the site of the purchaser. For that, every coil should be tightly wrapped by proper and secure seaworthy packing.
9) Each coil should have a separate label made of steel sheet with a reasonable size. This label should contain the following information: will be given upon production
10) The price should be valid for at least Two Month and must be based on steel NET weight.
Please provide a quotation to the following requirement from importer -
Product Name : FC Steel Wire Rope
Specifications:
Right hand medium-coarse steel rope size (10 mm) with fiber core rope qty 2000 meter
Left hand coarse steel rope size (20 mm) with fiber core rope qty 240 meters
Left hand coarse steel rope size (24 mm(1”) 9 outer strands have 16 wire each )with fiber core rope qty 300 meters
Please provide a quotation to the following requirement from importer -
Product : Copper Conductor Power Cables
Specifications:
- Copper Conductor
70 mm2 as per the following specs
1) COPPER CONDUCTOR, 70 mm2
QTY needed 5000 meters - 19/2.25 70 SQ.MM. ON DRUMS OF 250 M .
Copper wires shall be stranded annealed wires, manufactured as per IEC 60228. Copper wires shall be round compacted. They shall be easy to use for earthing.
The conductor shall be manufactured and tested in accordance with IEC standards, on wooden drums of the length specified below in meters, in one continuous piece without any joints.
PRICE VARIATION DATA COPPER PRICES
- PRICES BASED ON USD 9600/TON OF COPPER.
Variable Price for copper conductors 70 mm2; respectively, according to the LME (London Metal Exchange) prices.
Payment Terms:
full irrevocable confirmed l/c at sight
Destination:
Jordan
Looking for suppliers from:
Worldwide
Product Description
The buyer would like to receive quotations for -
Product Name: Ductile Iron Pipe
Specifications:
DUCTILE PIPES 450mm/18” 16 BAR QTY 72 METERS
DUCTILE COLAR SOCKET 450MM/18” 16 BAR QTY 6 EACH
DUCTILE FLANGE ADAPTER 450mm/18” 16 BAR QTY 6 EACH
DI pipes shall be centrifugally cast(C Class), with socket and spigot ends, EPDM rubber gaskets, according to EN545:2010
DI PIPES ACCORDING TO EN 545-2010
The joints of ductile iron (DI) pipes and fittings shall be TYTON type.
Outside protection coating:
Shall be of 400 g/m² metallic zinc Aluminum Alloy (85%+15%) plus epoxy finishing coat according to EN 545, applied also on socket inside, suitable for ground condition I and II and III. The external surface of the pipe spigot end at a minimum length of 250 mm shall have non toxic epoxy paint applied to a minimum dry film thickness of 100 microns. The internalsurface of the socket end shall be painted with a layer of zinc rich epoxy paint 150g/m²(zinc content not less than 85%° plus a layer of non toxic epoxy paint to aminimum dry film thickness of 100 microns.
Inside protection lining:
Cement mortar according to ISO 4179 – 1985.
2.2 Length of Pipes
Standard length for pipes is 6 meters for transport in bundles or 5.5 -5.8 meters for transport in open top containers.
2.3 Testing
The manufacturer shall demonstrate the conformity of his products with the standards by submitting the below performance tests specified in the standards:
• Compressive strength of the cement mortar lining.
• Leak tightness of flexible joints to positive internal pressure.
• Leak tightness of flexible joints to negative internal pressure.
• Leak tightness of flexible push-in joints to positive external pressure.
• Leak tightness of flexible joints to dynamic internal pressure.
• Leak tightness and mechanical resistance of flanged joints.
• Leak tightness and mechanical resistance of screwed and welded flanges.
The test should include:
• Dimensions Examination.
• Wall Thickness.
• External Diameter.
• Internal Diameter.
• Length
• Straightness of the pipes
• Ovality Test of the Pipes.
• Cement Lining Thickness.
• Tensile Test.
• Elongation test
• Hydrostatic pressure test.
• Hardness Test.
• Microstructure Examination supported by pictures
• thickness of external paint coating
• works leak tightness test for pipes and fittings
pipes and coating materials shall be certified for potable water use and shall contain
no ingredients that may migrate into water in amounts that are considered to be toxic or
otherwise, dangerous for health
Quantity Required : 100 Piece/Pieces
Shipping Terms : CIF
Destination Port : Jordan
Payment Terms : full irrevocable confirmed l/c at sight
