Product Description
Tube drawing die is mainly used for drawing copper tube, steel tube and other pipe materials, usually use together with floating plug, tube drawing die control outer diameter size of tube, floating plug control inner diameter size of tube. Our drawing dies are made of high purity tungsten powder the size area are 20% longer than common mould,these factors make sure our wire drawing dies can work longer !
we can also produce the following types S20 21 S22 23 30-31E.
Note: Other specification can be made upon customer's requirements.
Grade density hardness t.R.S( mpa) application
Yg6 14.9 91.0 hra 2350
Yg8 14.7 89.5 hra 2350
All raw material are tested in terms of density, hardness and t.R.S before use.
There are strict inspection on process and final products.
Every batch of product can be traced
Wire drawing is a metalworking process used to reduce the cross-section of a wire by pulling the wire through a single, or series of, drawing die(s). There are many applications for wire drawing, including electrical wiring, cables, tension-loaded structural components, springs, paper clips, spokes for wheels, and stringed musical instruments.
Our drawing dies are made of high purity tungsten powder the size area are 20% longer than common mould,these factors make sure our wire drawing dies can work longer!
we can also produce the following types:Z11,w.v.s13,S12,S10,S01,L,13,11
Note: Other specification can be made upon customer's requirements.
1/ GENERAL INTRODUCTION OF TUNGSTEN CARBIDE DRAWING DIES:
Tungsten carbide wire drawing dies, wire coating dies, PCD dies for drawing use for drawing various ferrous and nonferrous wires
tungsten carbide dies
tungsten carbide drawing dies
tungsten carbide nibs
tungsten carbide wire guide dies
PCD dies
Both carbide dies nibs and finished products with steel case are supplied
2968 Tungsten Carbide Tube Drawing Dies Suppliers
Short on time? Let Tungsten Carbide Tube Drawing Dies sellers contact you.
Tungsten carbide wire drawing dies, wire coating dies, pcd dies for drawing use for drawing various ferrous and nonferrous wires
Tungsten carbide dies
Tungsten carbide drawing dies
Tungsten carbide nibs
Tungsten carbide wire guide dies
Pcd dies
Both carbide dies nibs and finished products with steel case are supplied
Wire drawing is a metalworking process used to reduce the cross-section of a wire by pulling the wire through a single, or series of, drawing die(s). There are many applications for wire drawing, including electrical wiring, cables, tension-loaded structural components, springs, paper clips, spokes for wheels, and stringed musical instruments.
Our drawing dies are made of high purity tungsten powder the size area are 20% longer than common mould,these factors make sure our wire drawing dies can work longer!
we can also produce the following types:Z11,w.v.s13,S12,S10,S01,L,13,11
Note: Other specification can be made upon customer's requirements.---chengdu woco carbide
Wire drawing is a metalworking process used to reduce the cross-section of a wire by pulling the wire through a single, or series of, drawing die(s). There are many applications for wire drawing, including electrical wiring, cables, tension-loaded structural components, springs, paper clips, spokes for wheels, and stringed musical instruments.
Our drawing dies are made of high purity tungsten powder the size area are 20% longer than common mould,these factors make sure our wire drawing dies can work longer!
we can also produce the following types:Z11,w.v.s13,S12,S10,S01,L,13,11
Note: Other specification can be made upon customer's requirements.
Our company's main products include nail-making die, cold heading die, special die, cemented carbide spherical mould tank,
cemented carbide nozzle, cemented carbide plate, cemented carbide roll, valve seat, valve core and so on, which are widely used in
mining, oil extraction, electronics, automobile, military and other fields.
Comented carbide WC nibs Wire drawing dies for various other ferrous and non-ferrous metal wire
Tungsten carbide nibs Wire drawing dies for various other ferrous and non-ferrous metal wire
Features of Tungsten carbide dies
1. Material:100% virgin raw material with submicron grain size
2. Grade: Various grades for choice
3. Advanced production equipments and testing equipments
4. Precious Ground and polished
5. High wear resistance,high hardness and impact toughness
6. Advanced technology, automatic pressing, HIP sintering and precision grinding
7. Samples & small orders are acceptable.
Application:
1. Used for making high temperature parts, wear parts, anti-shielding parts and corrosion-resistant parts.
2. Used in making hardware and standard stamping moulds.
3. Applicable for electronic industry, motor rotor, stator, LED lead frame, EI silicon sheet and so on.
4. Used for producing drawn mold, wear-resistant parts, stamping parts and automatic press with punch.
5. Used for stamping die, extrusion die, stamping molds.
6. Drawing many kinds of steel wire, aluminum wire, high carbon, MS wire etc
Free smaple was available!
With more than 16 years experience of tool manufacturing in carbide and steel material for nail machines.
In this period,we have gained a good knowledge of the machine types for which these tools are supplied,
as well as the expertise to know which grade of carbide best suits each tool type.
Tools for nail making machine are:
Gripper dies
Cutter dies
header dies
A set of shaped cutters strike the other end of the wire. This cutter forms the point of the nail and at the same
time cut the nail from the rest of the wire. The gripper dies release and feed the wire forward for the next nail.
The formed nails are then collected in bins.
Gripper dies can be used for making nails from copper, stainless steel, aluminum, iron, zinc and many more.
Gripper Dies are those dies which are used in making nails in fasteners industries
High Precision Steel Pipe for Gas spring Cylinder
Type:Seamless and Welded Steel Tube
Roughness 0.1-0.8ra
Material E195-E235,Q195-Q235,#10,#20,#45,SAE1010,SAE1020
Surface:Black/bright
Standard:DIN, GB, JIS, DIN 17175, DIN 2391, GB 5310-1995, GB/T 13793-1992, GB/T 3094-2000, GB/T 8163-1999, JIS G3101
Size :OD 3mm-140mm Thickness 0.5-20mm
Processing :Cold rolled /cold drawn
1. BK (+C) No heat treatment after last cold forming process.
2. BKW (+LC) After last heat treatment there is a light finishing pass (cold drawing)
3. BKS (+SR) After the final cold forming process the tubes are stress relieve annealed.
4. GBK (+A) After the final cold forming process the tubes are annealed in a controlled atmosphere.
5. NBK (+N) After the final cold forming process the tubes are annealed above the upper
Woven bag / wooden or crate carton/ Bundle Packing/ Plain end or vanished as per customer's request.
Usage: Gas Spring Cylinder
High Precision Steel Pipe for Gas spring Cylinder
Type:Seamless and Welded Steel Tube
Roughness 0.1-0.8ra
Material E195-E235,Q195-Q235,#10,#20,#45,SAE1010,SAE1020
Surface:Black/bright
Standard:DIN, GB, JIS, DIN 17175, DIN 2391, GB 5310-1995, GB/T 13793-1992, GB/T 3094-2000, GB/T 8163-1999, JIS G3101
Size :OD 3mm-140mm Thickness 0.5-20mm
Processing :Cold rolled /cold drawn
1. BK (+C) No heat treatment after last cold forming process.
2. BKW (+LC) After last heat treatment there is a light finishing pass (cold drawing)
3. BKS (+SR) After the final cold forming process the tubes are stress relieve annealed.
4. GBK (+A) After the final cold forming process the tubes are annealed in a controlled atmosphere.
5. NBK (+N) After the final cold forming process the tubes are annealed above the upper
Woven bag / wooden or crate carton/ Bundle Packing/ Plain end or vanished as per customer's request.
Usage: Gas Spring Cylinder
High Precision Steel Pipe for Gas spring Cylinder
Type:Seamless and Welded Steel Tube
Roughness 0.1-0.8ra
Material E195-E235,Q195-Q235,#10,#20,#45,SAE1010,SAE1020
Surface:Black/bright
Standard:DIN, GB, JIS, DIN 17175, DIN 2391, GB 5310-1995, GB/T 13793-1992, GB/T 3094-2000, GB/T 8163-1999, JIS G3101
Size :OD 3mm-140mm Thickness 0.5-20mm
Processing :Cold rolled /cold drawn
1. BK (+C) No heat treatment after last cold forming process.
2. BKW (+LC) After last heat treatment there is a light finishing pass (cold drawing)
3. BKS (+SR) After the final cold forming process the tubes are stress relieve annealed.
4. GBK (+A) After the final cold forming process the tubes are annealed in a controlled atmosphere.
5. NBK (+N) After the final cold forming process the tubes are annealed above the upper
Woven bag / wooden or crate carton/ Bundle Packing/ Plain end or vanished as per customer's request.
Usage: Gas Spring Cylinder
High Precision Steel Pipe for Gas spring Cylinder
Type:Seamless and Welded Steel Tube
Roughness 0.1-0.8ra
Material E195-E235,Q195-Q235,#10,#20,#45,SAE1010,SAE1020
Surface:Black/bright
Standard:DIN, GB, JIS, DIN 17175, DIN 2391, GB 5310-1995, GB/T 13793-1992, GB/T 3094-2000, GB/T 8163-1999, JIS G3101
Size :OD 3mm-140mm Thickness 0.5-20mm
Processing :Cold rolled /cold drawn
1. BK (+C) No heat treatment after last cold forming process.
2. BKW (+LC) After last heat treatment there is a light finishing pass (cold drawing)
3. BKS (+SR) After the final cold forming process the tubes are stress relieve annealed.
4. GBK (+A) After the final cold forming process the tubes are annealed in a controlled atmosphere.
5. NBK (+N) After the final cold forming process the tubes are annealed above the upper
Woven bag / wooden or crate carton/ Bundle Packing/ Plain end or vanished as per customer's request.
Usage: Gas Spring Cylinder
2968 Tungsten Carbide Tube Drawing Dies Suppliers
Short on time? Let Tungsten Carbide Tube Drawing Dies sellers contact you.
