Very thin and tensile wires of low keff loss
Hence more wafters per cut and less fractures
Make higher productivity
Tight diameter and ovality tolerances
A wide range of spool types
An advanced winding technology
INTRODUCTION:115UM/120UM/ 0.16mm Silicon Wafer Cutting Ultra Fine Sawing Auto Glass Cut Out Wire
17 years of history in steel wire transforming and coating
Listed on Shenzhen A stock market in 2007
An annual output of 10,000 tons of sawing wire
ISO/TS 16949 And ISO9002 certificated
SILICON WAFERS are the building blocks of modern technology, they provide the substrate onto which circuits are constructed. We offer Prime, Test, Monitor, SEMI standard, and customized silicon wafers in all diameters from 2�¢?�³ to 300mm. Our Wafers meet the SEMI standards, along with customized options.
Silicon On Insulator (SOI) Wafers: Chips fabricated on SOI wafers achieve 30% faster speeds and 80% lower power demands compared to CMOS devices. The SOI structure consists of three layers: a top active device layer for transistor fabrication, a buried oxide (BOX) insulator layer, and a bottom handle wafer layer.
Silicon Float Zone Wafers: is a crystal growth technique that produces highly pure silicon wafers with fewer impurities than traditional methods.
Silicon Thermal Oxide Wafers: Has high quality silicon thermal oxide wafers in all diameters from 2�¢?�³ to 300mm.
Silicon Nitride Wafers: Has different option of film processing for your silicon needs, including LPCVD nitride.
On Insulator (SOI): Has high quality silicon thermal oxide wafers in all diameters from 2�¢?�³ to 300mm.
Fused Silica Wafers: is the amorphous phase of quartz (SiO2).
Borofloat 33 Glass Wafers: is used in a wide range of applications like micro-optics, sensors, microlithography, semiconductor engineering, lighting, medical technology.
We put forward a high quality of assortment of Nickel which is available
in many forms including LME registered and non registered cathodes,
cut cathodes, briquettes, pellets, disks, shots, granules, foil, powder,
flakes, sheet, wire, mesh, spheres, “evaporation slugs”, and rods.
Nickel is a silvery white metal that takes on a high polish. It is hard, malleable, ductile,
somewhat ferromagnetic, and a fair conductor of heat and electricity
The Incinerated scrap or E46, is the by-product derived from the reprocessing of incinerated domestic waste.
After the combustion process, the furnace output (IBA Incinerator bottom ash) is firstly washed, magnetically separated and screened to separate any no ferrous material.
At a visual inspection, the material is fragmentized, with iron and steel parts, resulting partly cut or in shredded form.
The stock appears heterogeneous and contains all kind of cut or dismantled steel parts such as sheets, bars, frames, wires, bolts and other iron/steel household residues.
The incinerated scrap is eventually oxidized, due to the thermal and cooling treatments, that the material has been submitted to. The burnt scrap also contains minor slag parts, ash and iron oxide, due to the recovery process.
Such components are inherent and adhere to the scrap surface. The total impurities, can be sorted, but not fully removed.
The consignment does not contain any type of arms, ammunition, mines, shells, cartridges, radioactive contaminated, or any other explosive material in any form either used or otherwise.
The collected stock, is stored in open air, on cemented flooring. It can be loaded loose in 20â?? heavy duty container.
Please feel free to contact us for further details.
The material is loose steel scrap processed through an incinerating plant for domestic waste followed by magnetic separation, fragmentized into pieces and consisting partly of tin coated steel cans.
At a visual inspection, the material is fragmentized, with iron and steel parts, resulting partly cut or in shredded form.
The stock appears heterogeneous and contains all kind of cut or dismantled steel parts such as sheets, bars, frames, wires, bolts and other iron/steel household residues.
The incinerated scrap is eventually oxidized, due to the thermal and cooling treatments, that the material has been submitted to. The burnt scrap also contains minor slag parts, ash and iron oxide, due to the recovery process.
Such components are inherent and adhere to the scrap surface. The total impurities, can be sorted, but not fully removed.
The consignment does not contain any type of arms, ammunition, mines, shells, cartridges, radioactive contaminated, or any other explosive material in any form either used or otherwise.
The collected stock, is stored in open air, on cemented flooring.
Due to the scrap dimensions and the material conditions, this particular scrap, should be carefully evaluated first, by the end users, to confirm its adequate recovery ratio and its suitability to be re-melted in the electric arc furnace.
Please feel free to contact us for further details
10891 Silicon Wafer Cutting Ultra Fine Sawing Wire Suppliers
Short on time? Let Silicon Wafer Cutting Ultra Fine Sawing Wire sellers contact you.
Qingdao Port, Tianjin Port, Shanghai PortUltra fine Steel Sawing Wire for cutting glass with below features:
Ultra fine Sawing wire for cutting glass with high carbon;
Ultra fine Sawing wire is cold drawing of brass plated of high strength steel wire;
Ultra fine Steel sawing wire for cutting glass with below application:
Ultra fine sawing wire can be used for cutting high hardness of monocrystalline silicon;
Ultra fine sawing wire can be used for cutting silicon and quartz material etc
Ultra fine sawing wire can be used for cutting glass, magnet
Ultra fine Steel Sawing Wire for cutting glass with below features:
Ultra fine Sawing wire for cutting glass with high carbon;
Ultra fine Sawing wire is cold drawing of brass plated of high strength steel wire;
Ultra fine Steel sawing wire for cutting glass with below application:
Ultra fine sawing wire can be used for cutting high hardness of monocrystalline silicon;
Ultra fine sawing wire can be used for cutting silicon and quartz material etc
Ultra fine sawing wire can be used for cutting glass, magnet
Hengxing science and techology co.,ltd built in 1995, with 24 years of steel wire transforming and coating industries, our main product as galavanized steel wire, strand, PC steel wire strand, steel cord radial tire, hyrolic hose and polycrystaline silicon. Listed on Shenzhen A stock market in 2007,we have independent R&D center, passed the ISO, SGS,BV certification and so on. As the biggest galavanized steel wire and srand manufacture in China, and the biggest steel cord for radial tire, with high quality and performance, our product widely used in the industries as electric cable, suspension construction, radial tire and hydrolic hose, and sawing.
Electro welded wire mesh supply In the forms of rolls or panels, for construction, fences and other industrial uses.
It enjoys the feature of corrosion resistance, compared with plain welded wire mesh. Mainly used as fencing panels or further fabricated into wire partitions, wire container panels, wire baskets, welded wire fences, poultry fences and other welded products.
Type: Electric Wire Mesh
Application: Fence Mesh
Hole Shape: Square
Wire Gauge: 2.0-4.0mm
Processing Service: Bending, Welding, Cutting
Product name: welded wire mesh
Wire diamter: 0.6-5 mm
wire space: 50-300 mm
Surface treatment: galvanized, PVC coated
Width: 500-1500 mm
Length: as request
Factory certification: ISO 9001
Sawing wire , also called ultra fine wire,is cold drawing high strengh brass plated steel wire with high carbon.
It can be used for cutting high hardness of single crystal line silicon,poly crystal line silicon,quartz material,etc.
(1)Sawing wire is a high grade steel wire that can be used to cut a wide range of products.It serves as the abrasive carrier in a Multi Wire Saw.
(2)The technique finds its origin in the world of solar cells. From the mid eighties, this technology was developed to decrease kerf loss and increase productivity.
(3)In the early nineties the method was introduced for slicing silicon ingots to wafers for the electronics industry. Since then the technique has been more and more introduced for cutting other hard and brittle materials as well.
(4)Saw wire is used to cut a wide variety of products, such as silicon, germanium, gallium aresenide, quartz, indium phosphide, to name only a few.
( 5 )Saw wire is mostly used in the production of solar cells. The use of photovoltaic energy is increasing, as humanity becomes more and more aware of the scarcity of the natural resources.
Advantage of
Sawing Wire for Solar Wafer Cutiing
Very thin and tensile wires of low keff loss
Hence more wafters per cut and less fractures
Make higher productivity
Tight diameter and ovality tolerances
A wide range of spool types
An advanced winding technology
Sawing wire , also called ultra fine wire,is cold drawing high strengh brass plated steel wire with high carbon.
It can be used for cutting high hardness of single crystal line silicon,poly crystal line silicon,quartz material,etc.
(1)Sawing wire is a high grade steel wire that can be used to cut a wide range of products.It serves as the abrasive carrier in a Multi Wire Saw.
(2)The technique finds its origin in the world of solar cells. From the mid eighties, this technology was developed to decrease kerf loss and increase productivity.
(3)In the early nineties the method was introduced for slicing silicon ingots to wafers for the electronics industry. Since then the technique has been more and more introduced for cutting other hard and brittle materials as well.
(4)Saw wire is used to cut a wide variety of products, such as silicon, germanium, gallium aresenide, quartz, indium phosphide, to name only a few.
( 5 )Saw wire is mostly used in the production of solar cells. The use of photovoltaic energy is increasing, as humanity becomes more and more aware of the scarcity of the natural resources.
INTRODUCTION:
17 years of history in steel wire transforming and coating
Listed on Shenzhen A stock market in 2007
An annual output of 10,000 tons of sawing wire
ISO/TS 16949 And ISO9002 certificated
Can provide all kinds of all kinds of the length of the wire, the line length subject only to the spool take-up capacity limit. H wheel type mainly includes NTC210 type, BS200, BS64, BS126, etc. According to customer needs to provide other specification size of h wheel.
Copper No. 2 kinds of alloy Wire cooper without lines, containing impurity, contain Copper quantity for 96% (minimum content 94%).
Shall not contain excessive lead and tin change of copper wire, welding of copper, brass and bronze line, excessive oil, prohibition and nonmetal,crisp, burning line, utterly margin of fine copper and excessive yarn. Need appropriate means to remove dirt. Birch Shall consist of clean, untinned, uncoated, unalloyed
copper wire and cable, not smaller than No. 16 B & S
wire gauge, free of burnt wire which is brittle
Copper No. 2 kinds of alloy Wire cooper without lines, containing impurity, contain Copper quantity for 96% (minimum content 94%).
Shall not contain excessive lead and tin change of copper wire, welding of copper, brass and bronze line, excessive oil, prohibition and nonmetal,crisp, burning line, utterly margin of fine copper and excessive sexual yarn. Need appropriate means to remove dirt. Birch
Shall consist of clean, untinned, uncoated, unalloyed
copper wire and cable, not smaller than No. 16 B & S
wire gauge, free of burnt wire which is brittle
Micro silica also known as fume, is an amorphous (non-crystalline) polymorph of silicon dioxide, silica. It is an ultrafine powder collected as a by-product of the silicon and ferrosilicon alloy production and consists of spherical particles with an average particle diameter of 150 mm. The main field of application is as pozzolanic for high performance concrete because of its extreme fineness and high silica.
Applications :
Silica is added to Portland cement concrete to improve its properties, in particular its compressive strength, bond strength, and abrasion resistance. These improvements stem from both the mechanical improvements resulting from addition of a very fine powder to the cement paste mix as well as from the pozzolanic reactions between the silica fume and free calcium hydroxide in the paste.
Advantages :
Addition of silica also reduces the permeability of concrete to chloride ions, which protects the reinforcing steel of concrete from corrosion, especially in chloride-rich environments such as coastal regions and those of humid continental roadways and runways (because of the use of deicing salts) and saltwater bridges.
Fly Ash is by product generated during combustion of coal, and comprises the fine particles that rise with the flue gases. Ash which is collected from the bottom is termed bottom ash. Fly ash is collected by electrostatic precipitators or other particle filtration equipment before the flue gases reach the chimneys of coal-fired power plants and together with bottom ash removed from the bottom of the furnace is in this case jointly known as coal ash. Depending upon the type of coal being used, the specification of Fly Ash varies considerably, but Fly Ash contains substantial amounts of silicon dioxide and calcium oxide (CaO), both being endemic ingredients in many coal-bearing rock strata. We are a reputed Fly Ash Exporter based in India and are supplying Fly Ash different cement, ready mix concrete, steel, refractories and construction industries.
The Major Utilization Areas Of Fly Ash :
- Manufacture of Portland Pozzolanic Cement & Performance improver in Ordinary Portland cement (OPC).
- Part replacement of OPC in cement concrete.
- High volume Fly Ash concrete.
- Roller Compacted Concrete used for dam & pavement construction.
- Manufacture of ash bricks and other building products.
- Construction of road embankments, structural fills, low lying area development.
- As a soil amender in agriculture and wasteland development.
Types of Fly Ash:
- According to the type of coal used fly is classified into two types. Anthracite and bituminous coal produces Fly Ash classified as class F. Class C Fly Ash is produced by burning lignite or sub-bituminous coal. Class C Fly Ash has self-cementing properties.
- Class F and Class C Fly Ash are products of the combustion of coal in large power plants. Fly Ash is collected in electrostatic precipitators or baghouses, and then transferred to large silos for shipment. When needed, Fly Ash is classified by precise particle size requirements, thus assuring a uniform, quality product.
- Class F Fly Ash is available in the largest quantities. Class F is generally low in lime, usually under 15 percent, and contains a greater combination of silica, alumina and iron (greater than 70 percent) than Class C Fly Ash.
- Class C Fly Ash normally comes from coals which may produce an ash with higher lime content generally more than 15 percent often as high as 30 percent. Elevated CaO may give Class C unique self-hardening characteristics.
Description: These beautiful Vietnamese silk lanterns are a wonderful way to decorate a room, home, hotel, event or restaurant and add an Asian atmosphere to any setting. They are made by hand from finely woven silk and bamboo using techniques invented long ago. They collapse into a tube for easy shipping and convenient storage. Simply pull up on the metal wire to expand the lantern into its shape. Additionally, each silk lantern comes with a convenient bracket mounted on top for easy hanging. We guarantee that you will love your lantern. By tradition, on the 14th day of each lunar month, the residents of Hoi An celebrate the Lantern Festival by turning off all the electric lights to allow thousands of these beautiful colored lanterns to glow throughout the town, adorning their porches and windows. They are an extremely important and beautiful cultural craft from Vietnam, which prides itself in beautiful silk and bamboo art works.
Description: These beautiful Vietnamese silk lanterns are a wonderful way to decorate a room, home, hotel, event or restaurant and add an Asian atmosphere to any setting. They are made by hand from finely woven silk and bamboo using techniques invented long ago. They collapse into a tube for easy shipping and convenient storage. Simply pull up on the metal wire to expand the lantern into its shape. Additionally, each silk lantern comes with a convenient bracket mounted on top for easy hanging. We guarantee that you will love your lantern. By tradition, on the 14th day of each lunar month, the residents of Hoi An celebrate the Lantern Festival by turning off all the electric lights to allow thousands of these beautiful colored lanterns to glow throughout the town, adorning their porches and windows. They are an extremely important and beautiful cultural craft from Vietnam, which prides itself in beautiful silk and bamboo art works.
The UV laser marking machine is developed by using a 355nm UV laser. This machine uses a third-order intracavity frequency doubling technology. Compared with infrared lasers, the 355nm UV laser has a very small spot, and the marking effect is directly interrupted by a short-wavelength laser. The molecular chain greatly reduces the mechanical deformation of the material. Thermal deformation (cold light), because it is mainly used for ultra-fine marking and engraving. It is especially suitable for applications such as marking, micro-hole drilling of food and pharmaceutical packaging materials, high-speed dicing of glass materials, and complex pattern cutting of silicon wafers.
Semi automatic saw bone meat machine With fine-tuning, bone meat cutting machine
Main features :
1.You can choose to use a single saw or a double saw for product stability,
or a single saw for unstable products .
2.Ensure the hygiene of the meat and ensure a smooth cutting surface
3.Waterproof design for quick cleaning
4.According to dfferent uses ,froze meat ,lamb chops, steak ,fish
5.Adopting human-machine interface and intelligent operation panel
6.30 sets of memory functions can be set
7.Feeding adopts servo motor ,with high precision
8.The conveyor belt can be removed for cleaning paramters :
cutting thickness: 1-50mm, Material thickness under 15cm .Capacity 8-15times/min
Parameters :
Voltage: 380V
Power: 1.5KW
Operating speed: 1500m/min
Saw blade length: 2000mm
Cutting ruler: 300 * 220mm
Workbench size: 657 * 525mm
Machine size: 800 * 600 * 1520mm
Machine weight: 80kg
10891 Silicon Wafer Cutting Ultra Fine Sawing Wire Suppliers
Short on time? Let Silicon Wafer Cutting Ultra Fine Sawing Wire sellers contact you.
