The shore hardness tester as-120 series including type(a, b, c, d, e, o, do, oo), model complete, with different probe size, use for different measured objects and hardness value, to meet different request for kinds of material hardness measure. integrated design, small volume, light weight, simple structure, easy to use, intuitive readings and automatic shutdown function.
with low battery alarm indicator & average value calculation function.
auto switch off and manual shutdown.
use usb data output with connection pc.
provide bluetooth data output choice.
Accuracy1h
Resolution:0.1h
Range:1090h
Operating temperature:040°c
Size:170x63x24 mm
Power supply2x1.5vaaa um-4 battery
Weight:310 g (not including batteries)
1, each durometer type is made to a specific scale (i. E.A, c, d) and is capable of producing a value between 0and 100. Shore a is designed to measure the penetration hardness of rubber, elastomers and other rubber like substances such as neoprene, silicone, and vinyl. It can also be used for soft plastics, felt, leather and similar materials. Shore d is designed for plastics, formica, epoxies and plexiglass.
2, it meets standards: din 53505, iso 868, iso 7619, astmd 2240, jisk7215.
3, used the exclusive micro-computer lsi-circuit and crystal time base to offer high accuracy measurement.
4, digital display gives exact reading with no guessing and errors.
5, can communicate with pc for reading, printing and analyzing by the optional software and cable for rs232c interface.
6, automatic power off to conserve power.
7, use operation stand of optional parts can get good accuracy and repetitiveness due to constant measurement force to eliminate the errors caused by artificially applied different force.
Color.................................Qualified
Odor....................................Qualified
Impurity..............................Qualified
Appearance...........................White powder
PH.......................................10.8
Moisture.................................10.3%
Ash......................................2.33%
Fineness....................................200 mesh 99.8% passed
MgO content....................................1.41%
Spots.......................................0.5/cm2
As.........................................0.21mg/kg
Pb............................................0.62mg/kg
Stability of hot paste..........................After 120 - 30min cooling, there is no hard lump that can not be crumbled in fingers.
Qualitative experiment..............................10 of suspending liquid is changed to purple or blue during the reaction of iodine
Color.................................Qualified
Odor....................................Qualified
Impurity..............................Qualified
Appearance...........................White powder
PH.......................................10.8
Moisture.................................10.3%
Ash......................................2.33%
Fineness....................................200 mesh 99.8% passed
MgO content....................................1.41%
Spots.......................................0.5/cm2
As.........................................0.21mg/kg
Pb............................................0.62mg/kg
Stability of hot paste..........................After 120 - 30min cooling, there is no hard lump that can not be crumbled in fingers.
Qualitative experiment..............................10 of suspending liquid is changed to purple or blue during the reaction of iodine
Sonokeling wood itself is a type of hardwood. The weight of rosewood wood is in the range of 0.77 to 0.86. Where from that weight there is approximately 15 percent water content. When viewed from the texture, sonokeling wood has a fairly smooth shape Table of Contents
What is Sonokeling Wood
Sonokeling Wood Characteristics
1. Black Color
2. Hard Texture
3. Sapwood Can Be Used
4. Anti Termite and Mushroom Attack
5. Berta Resembling Metal
Benefits of Sonokeling Wood
Examples of Objects from Sonokeling Wood
1. Furniture
2. Musical Instruments
3. Accessories
4. Tableware
Book Recommendations
1. Unique Lamp Creations from Unused Materials
2. 3D Room Drawing Series: 22 Multifunctional Furniture Designs
3. Various Inspirations for Simple Minimalist Furniture Arrangements
4. Designing and Assembling Wooden Furniture: Etb
2968 Shore Hardness Tester As 120 Series Suppliers
Short on time? Let Shore Hardness Tester As 120 Series sellers contact you.
JHG tinted glass is produced by metal oxides to the float glass. The colour may be transferred in the series of blue, green, grey, bronze flexibly. The performance of visible light, privacy and solar heat transmission will be changed arrording the colour change. Different tinted glass offers varied application possibility-from interior partitions, to home appliance, to furniture, to facades and auto field. Reflective glass is float glass with a metallic coating that cuts off solar heat.The coating film may provide mirror effect, preventing visibility from outside and preserving privacy. JHG mainly offer 2 kinds of reflective glass. Hard reflective glass (on line) includes blue, green, grey, bronze, pink, silver colour, Soft reflective glass (off line) includes golden, silver, purple colur.
Specification
SOLAR GLASS
JHG solar glass including texture glass and flat glass ,it is the nice performance low iron glass with high solar transmittance, and low reflection .
After tempered, it will be the ideal choice for photovoltaics, solar thermal collector ,and greenhouse .
Size
Maximum Size:1665*2200mm
Minimum Size: 300*300mm
Specifiction
Main thickness 2-5mm
Dimension tolerance �?�±1.0mm
Thickness tolerance �?�±0.2mm
Diagonal tolerance 0.2%
Overall bow <0.2%
Iron content 110ppm
Solar transmittance from 91.5-99%
(wavelength rang 380-1100mm)
Hardness H
Main glass series
2-5mm Tempered low iron float glass
2-5mm Tempered low iron texure/mistlite glass
2-5mm AR coating glass
2-5mm High hazed tempered glass
2-5mm silk printed tempered glass
The nonionic surfactant of nonyl phenol polyoxyethylene ether was synthesized by condensation reaction of nonylphenol and ethylene oxide under the action of catalyst.
There are various kinds of hydrophilic equilibrium value (HLB value). This product has a wide application in detergent/printing/dyeing/chemical.
This product has good osmotic/emulsifying/dispersing/anti-acid/anti-alkali/resistance to hard water/resistance to reduction/oxidation resistance.
This series of nonylphenol polyoxyethylene ether can be widely used as W/O emulsifier or O/W emulsifier, dispersant, is the main raw material of synthetic detergent. It is widely used in industrial cleaning, textile printing and dyeing, paper making, leather chemical industry, chemical fiber oil agent, oil field additives, pesticides, emulsion polymerization and other industrial fields.
Tx-10 can be used as a compound monomer of chemical fiber oil, used in the textile printing and dyeing industry as a bleaching, refining, dyeing process of the diffusion agent, leveling agent, oil field wetting agent, foaming agent, mud active treatment agent. Metal processing, machinery, chemical, pesticide, rubber and other industries as emulsifier, cleaning agent
Glass GRADE
"Glass grade properties" typically refer to the specific characteristics and qualities of glass that determine its suitability for various applications. Glass comes in a wide range of types and grades, each with its own set of properties that make it suitable for different purposes.High grade silica sand manufacturer for Glass Industries serving both Float glass as well as container glass Industries.
We manufacture around 10000 tons of glass grade sand per month. Here are some important glass grade properties:
Properties:
80 - 120 ppm
Transparency: Glass is known for its transparency, allowing light to pass through. The level of transparency can vary based on factors such as the type of glass, its thickness, and any coatings or treatments applied to it.
Hardness: Glass is a hard material, but its hardness can differ based on the specific type of glass. Some glasses are more scratch-resistant than others.
Lx-c durometer meter applied to foam, sponge, shoe materials, such as durometer testing of materials with low hardness. This product is light hg/t2498-93 and other relevant standards.
1. Dial value: 0 ~100hc
2. Needle stroke: 2.5 mm
3. Measure range: 10 ~90hc
4. Needlepoint size: sr 2.5 mm
5. Dimension:115¡¡§¡é60¡¡§¡é25mm
6. Weight: 0.5 kg
Features:
* LCD display of 128 64 matrix is used.
* Hardness scales(HV ,HB,HRC,HRB,HRA,HS).
* RS232 interface and USB to PC
* Max 600 groups impact times:32¡«1 of data can be stored at internal.
* Back light display has been used to make convenient or the user in poor light.
* Upper and lower limit can be preset. It will alarm automatically when the result value exceeding the limit.
* Material of cast steel¡± is added HB values can be read out directly when D/DC impact device is used
to measure cast steel¡± workpiece.
* Power is two of AA battery. Continuous working period: approx. 100 h (no back light on).
* Software of PC can be installed according to the requirements of user. The function will be more powerful
to satisfy the more demands of quality control and management.
Property Unit
Typical Value
Mass density g/cm 3 0.941-0.959
Melt flow Rate(190 centidegree /2.16kg) g/10min 1.0
Tensile yield strength MPa 19.0
Flexural modulus Mpa 965
Elongation@ break % 400
Impact Embrittlement temperature centidegree MAX -118
Dielectric Constant 100KHZ 2.32
1MHZ 2.31
Loss Tangent 100KHZ MAX 0.0001
1MHZ MAX 0.0001
Volume resistivity OHM-CM MIN 1x10 15
Application
Mainly used for the production of high toughness of the telephone,cable insulation material
LDPE:
Physical Properties Test Method Nominal Value Unit
Density ISO 1183 0.921 g/cm3
Melt Mass-Flow Rate (MFR) ISO 1133 1.9 g/10min
Hardness
Shore Hardness (shore D) ISO 868 45
Mechanical Properties
Tensile Modulus ISO 527-2 175 MPa
Tensile Strength Yield, ISO 527-2 9.0 MPa
Break, 13.0 MPa
Tensile Strain(Break) ISO 527-2 850 %
Modulus of Elasticity Internal Method 250 MPa
Thermal
Vicat Softening Temperature ISO 306/A50 89.0 �°C
Melting Temperature (DSC) DIN 53765 108 �°C
Peak Crystallization Temperature (DSC) DIN 53765 97.0 �°C
Heat of Fusion DIN 53765 110 J/g
Electrical
Volume Resistivity ASTM D257 8.5E+15 ohm â?¢cm
Dielectric Strength ASTM D149 30.0 kV/mm
Dielectric Constant (60Hz) ASTM D150 2.20 %
Dissipation Factor (60 Hz) ASTM D150 0.00050
LLDPE
Properties Test conditon Test method Test data Unit
Density 0.91
MFI 2
Drop impact strength ASTM D-1709 90 g
Elongation ,vertical/horizontal ASTM D-882 600/800 %
tensilestrength,thermal resistance ASTM D-1004 105/95 Kg/cm
elongation ASTM D-638 930 %
tensile strength ASTM D-638 180
tensile strength,vertical/horizontal ASTM D-882 380/350
Vicat softening point ASTM D-1525 103 C
melting point ASTM D-2117 126 C
Turbidity ASTM D-1009 12 %
45 glossness ASTM D-2457 75 %
1. Production: basalt fiber fabric is made of continuous basalt fiber textile yarn through warping, weaving and coating.
2. Weaving methods according to requirements: unidirectional cloth, plain cloth, twill cloth and grid cloth.
2. Application: reinforced mesh cloth, fireproof cloth, fishing rod cloth, luggage decoration cloth, electrical insulation cloth, bulletproof cloth, etc.
3. Packaging: 100M / roll (or customized as required).
4. Performance: high strength, high temperature resistance, good electrical insulation, non hygroscopic, acid and alkali corrosion resistance.High temperature resistance 1000 �° C
5. Specification and model: bfw16 * 20-100 (120)
BFW: basalt fiber fabric;Completely replace carbon fiber sheet building reinforcement
16 * 20: the warp and weft density of yarn is 16 and 20 pieces / cm respectively;
100: the width of the fabric is 100 cm;
(120): the mass per unit area of fabric is 120 g / m2.
BFNP5*5-200(160)
BFNP: basalt fiber mesh cloth (coated and shaped);
5 * 5: the longitude and latitude mesh size of the cloth surface is 5 and 5mm;
200: the width of the grid is 200 cm;
(160): the weight of grid cloth per unit area is 160g / m2.
Tubular finger fixation for phalangeal fractures, knuckle dislocations, ligaments, tendon injuries and fixation.
190*120*3.2mm
LOW TEMPERATURE THERMOPLASTIC SHEET
Product features:
Low temperature thermoplastic sheet is a new type of material made of specially synthesized polymer polycaprolactone treated by a series of chemical methods. Molecules are in a stable state at room temperature (10-30C), and can be softened after being heated in 65-70C water for 1-3 minutes. Curing in 3-5 minutes at room temperature.
It has the advantages of light weight, high strength, good air permeability, not afraid of water, non-toxic, odorless, non-irritating to the skin, etc., and has biodegradability.
Scope of application:
1. Fixation after reduction of fractures and joint dislocations
2. Postoperative fixation of soft tissue injuries such as joint ligaments, nerve and tendon injuries
3. Bone, joint tuberculosis, acute and chronic osteomyelitis, septic arthritis, primary bone Fixation during conservative treatment such as tumor
metastasis or after debridement
4. Joint deformity, nerve palsy, cerebral palsy, scoliosis correction and postoperative fixation in children and fixed
5. Fixation after burns and other plastic surgery operations
6. Production and application of rehabilitation braces and orthoses
7. Posture placement and fixation during radiotherapy
Product Features;
Six Impact Devices are available for special applications(D,DC,D+15,C,DL,G)
Direct display of hardness scales HRB,HRC,HV,HB,HS,HL;
Software to connect with PC and Dataview for PC operation;
Automatic identification Impact Devices and test direction (Except G);
Software data and upperlower limits setting and sound alarm;
Time and date setting; auto-clock;
On-Board memory holds 240-1000 groups of data;
Integral thermal printer, print all test results and histogram;
For all metallic materials;
Li Battery , low voltage indication and sound alarm;
LCD with blue back-light, showing all functions and parameters;
Wide measuring range;
Long standby time and stable performance of field work;
Technical specifications:
Hardness Scale:HL,HRC,HRB,HV,HB,HS
Accuracy:í+4HLD(760í+20HLD) repeatability of displayed value
Standard Impact Device:D
limits set measuring range:(170~960)HLDD Optional Impact
Devices:C DC D+15 DL G
Operating Temperaturee:0~40
Statistics Function:Average Max Min calculation,limits setting and alarm
Testing direction:Automatic
Min.thickness of hardened:0.8mm
Chargeing time:3~5hours
Power:Li Battery 4.2V/1600mAh
Charger:5V/500mA
Overall Dimensions:147*69*23mm
Weight:186g
Computer Interface:RS232
Min.Workpiece thickness:5mm (D DC DL D+15)1mm (C)10mm (G)
memory:240~1000 groups
Min.Workipece Weight:2~5Kg on stable support 0.05~2Kg with compact coupling
Min.Radius of Workpiece:Rmin=50mm(with support ring Rmin=10mm) Max.Workpiece
Hardnesss:996HV (D DC D+15 DL C) 646HB (G)
Continuous Working Time:About 200hours
Wide measuring range, for all metallic materials
Direct display of hardness scales hrb, hrc, hv, hb, hs, hl
Conversion to tensile strength (u.T.S.)
Test at any angle, even upside down
Removable printer included
Six impact devices are available for special applications
Large lcd display showing all functions and parameters
Battery low indication
New function of software calibration
Power charging indication on the keyboard led
Fault distinguish in details
FH products are Pure nonionic derived the endosperm of guar polysaccharide (Cyamopsos tetragonolobus). The products are unique with ultra-high viscosity with fastest hydration characteristics as shown in Figure 1 below. Also, when added with other drilling components, to seawater, a KCl solution or other aqueous system, the product suspension disperses readily without lumping, even under low-shear conditions generating most of its full viscosity within just a few minutes.
PRODUCT COMPATIBILITY:
FH series of products are compatible with most of the chemicals and auxiliaries used in drilling operations. However, the products are not compatible with Arabic and Crystal gums. Also, in presence of borates they form elastic gel.
PRODUCT APPLICATIONS:
FH series of products are natural, high viscosity, fast hydrating non-Newtonian hydrocolloids with suitable cross linking components in diesel slurries and are versatile for continuous mix applications, where extremely fast hydration and subsequent viscosity development is required. They are excellent viscosifiers, stabilizers, thickeners and suspending agent for use in oil-drilling, workover fluids and several other oilfield applications like hydraulic fracturing, oil well stimulation, mud drilling, oil well capping, flocculent and liquid shoring etc. The product is used as a surfactant; synthetic polymer and deformer ideally suited for all rheological requirements of water based and brine based drilling fluids.
Specifications:-
PRODUCT : FH-35 FH-38 FH-42
CAS No. : 9000-30-0 9000-30-0 9000-30-0
Granulation : FINE FINE FINE
APPEARANCE : OFF WHITE POWDER
MOISTURE : 8% Max. 8% Max. 8% Max.
PROTEIN (N X 6.25) : 5.0% Max 5.0% Max 5.0% Max
ASH : 1.5% Max. 1.5% Max. 1.5% Max.
ACID INSOLUBLE RESIDUE (A.I.R.) : 3% Max. 3% Max. 3% Max.
CARBOHYDRATE (incl gum by difference) : 82% Min 82% Min 82% Min
pH (1% Solution) : 5.5 ? 6.5 5.5 ? 6.5 5.5 ? 6.5
VISCOSITY :
(0.48% Product in 2% KCL Sol. 2.5 mins mix @1500 RPM in waring blender) Fann 35sa Viscometer at 300 RPM, 25�C 3 Mins : 35 3 Min:38 3 Mins : 42
5 Mins : 37 5 Mins : 39 5 Mins : 43
30 Mins : 39 30 Mins : 42 30 Mins : 45
60 Mins : 40 60 Mins : 43 60 Mins : 47
