Item Unit model
AGS-060WSL
Refrigerant -10degree kW 94.1
-20degree 64.2
-30degree 40.1
Power 3φ 380V 50Hz
Total input power kW 45.4
Compressor Type Semi hermetic screw
Power kw 45.4
Refrigerant R22/R404A
Start-up model Y-Triangle
Evaporator Type Shell and Tube
Chilled fluid flow m³ /h 29.5
Condenser Type Shell and Tube
Cooling water flow m³ /h 23.9
Inlet/outlet pipe diameter Evaporator Inch 3"
Condenser Inch 3"
Drain out port Inch 1"
Dimension Length(L) mm 2130
Width (W) mm 855
Height(H) mm 1540
Weight Net weight kg 950
Running weight kg 1060
Note:
1. Nominal cooling capacity calculated according to:
The chilled fluid is the 60% Ethylene Glycol aqueous solutions.
Inlet/outlet cooling water temperature: 32degree/37degree
2. Working condition:
The temperature range of chilled fluid is from -5degree to -30degree
Temperature difference between inlet and outlet chilled fluid is from
2.5degree to 10degree
The temperature range of cooling water from 22degree to 37degree
Temperature difference between inlet and outlet cooling water is from 3.5degree to 10degree.
TI UNIT screw chillers are manufactured in two types of air cooled and water cooled in capacities from 50 to 560 T.R. in one to four circuited configurations. Evaporators and condenser Chillers with plate type heat exchangers are available upon request. For further related technical information, please send your inquiries to TI UNIT mfg. group.
TI UNIT screw chillers can be designed to operate with R-22 and R-134a refrigerants. Bitzer screw compressors suitable for use with R-134a refrigerant are available in two versions (m.vr.1 & m.vr.2) which can be used in the chillers as required.
Safety controls installed on all units include high and low pressure cut-outs, compressor oil level control safety cut-out, water anti freeze thermostat, water flow switch and evaporator entering water thermostat and compressor operation time logger. The above mentioned are all chosen from the most recognized controls manufactures in the air conditioning industry. Compressors are by Bitzer which happens to be one of the best and most reliable brands. Raw materials such as copper tubes, fittings and valves are supplied by well-respected manufactures. Electrical safety measures such as three phase controller and circuit breakers, are available on all units.
A fault detection system for the whole unit is available upon request. Microprocessor based PLC controller is also available as needed.
TI UNIT screw chillers are also available upon request for industrial applications in both Air Cooled and Water Cooled types; Suitable accessories make the chillers operable in all seasons according to the application requirements without any problems.
Screw Chiller adopt the best (semi-hermetic) screw compressor from abroad, and operate credibility, high efficiency, easy to maintain, exact volume control, a wide range of application. The system adopts the latest asymmetric rotor profile. Build-in pressure drop lubricant to system with low vibrations, sound emissionshigh sealing performance.
Screw Chiller's human machine interface configures a full touch screen, which enables automatic control and accurate monitoring. The advantages of unit: waterproofdustproof, corrosion resistant, long life. Step or stepless capacity control, the unit ensure that it bring into the most energy-saving effective in any load conditions.
Screw Chiller due to use heat copper tube and high efficiency compressor with high effective thermal expansion current-saving device, the unit will operate in stability, longer and effectively.
Screw Chiller adopts a reliable safety protection device: to prevent compressor starting frequently, over-current protection, overheat of motor protection, prevent freezing, sight glass in liquid, oil heating protection, phase protection, HV/LV protection, discharge high-temperature protection, safety value, soluble clock, water shut-off protection, and so on.
1. Cooling capacity: 126.2kw~2285.4kw
2. liquid inlet temperature is 12 degrees, outlet temperature is 7 degrees.
3. Cooling water inlet temperature 30 degrees,outlet temperature 35 degrees.
4. Input power: 3P-380V-50Hz, Allowable fluctuate voltage: ± 10%, allowable voltage difference in phase: ± 2%. ( 3P-415V-60HZ and 3P-230V-60HZ is ok)
5. Accept orders for special requirements.
6. Industrial and durable design, with stainless steel water tank and high-lift pumps.
7. Wide range of variable chilled water temperature to meet the industrial requirements throughout whole year.
8. Designed as an independent refrigeration circuit, each compressor corresponding to one refrigeration circuit.
9. Refrigerant use R22 or Friendly choose to use environmentally R404A or R134A refrigerant.
10.COP over than 4.02
11.Guarantee for 1Year
As a leading air cooled screw chiller supplier, TopChiller provides a complete range of air-cooled screw chiller from TPAS-ASH series, with cooling capacity from 40Ton to 580Ton/130KW to 1950KW and the chiller temperature control range is +30 to -30.
Besides the standard air-cooled screw chiller control temperature of 7 to 30, TopChiller also has air-cooled glycol screw chiller control temperature below zero from 0 to -30.
Each air cooled screw chiller designed from TopChiller has the following features:
Using world famous brand semi-hermetic screw compressor- Bitzer from Germany and Handbell from Taiwan.
Each screw compressor with 4 steps of energy control 25%-50%-75%-100% to make sure the whole screw chiller is stable and guarantee high refrigeration performance. There are also 2 or 3 compressors for optional depends on the required refrigeration capacity.
Highly efficient closed loop shell and tube type heat exchanger as the evaporator, and using air cooled type condenser-Copper tube sleeve aluminum fin with big volume air cooling fan.
As a leading water-cooled screw chiller manufacturer with almost 20 years of experience since 2003, TopChiller provides a complete range of water-cooled screw chiller from TPWS-WSH series.
The cooling capacity of screw water chiller is from 30Ton to 480Ton/105KW to 1688KW and the chiller temperature control range from +30 to -30.
Besides the standard water-cooled screw chiller control temperature from 7 to 30, TopChiller also has a water-cooled glycol screw chiller control temperature below zero from 0 to -30 for some special industrial applications.
With 20 years experience in design and manufacturing water-cooled screw chiller from TopChiller has the following features:
Using famous brand Semi-hermetic Screw Compressor- Bitzer from Germany and Handbell from Taiwan.
Each screw compressor comes with 4 steps of energy control 0-25%-50%-75%-100% to make sure the whole screw chiller operates when stable with high refrigeration performance.
Each water-cooled screw chiller with high-efficiency shell and tube type heat exchanger and aluminum foil with a copper tube air cooled condenser.
22776 Screw Chiller Suppliers
Short on time? Let Screw Chiller sellers contact you.
As a leading water-cooled screw chiller manufacturer with almost 20 years of experience since 2003, TopChiller provides a complete range of water-cooled screw chiller from TPWS-WSH series.
The cooling capacity of screw water chiller is from 30Ton to 480Ton/105KW to 1688KW and the chiller temperature control range from +30 to -30.
Besides the standard water-cooled screw chiller control temperature from 7 to 30, TopChiller also has a water-cooled glycol screw chiller control temperature below zero from 0 to -30 for some special industrial applications.
With 20 years experience in design and manufacturing water-cooled screw chiller from TopChiller has the following features:
Using famous brand Semi-hermetic Screw Compressor- Bitzer from Germany and Handbell from Taiwan.
Each screw compressor comes with 4 steps of energy control 0-25%-50%-75%-100% to make sure the whole screw chiller operates when stable with high refrigeration performance.
Each water-cooled screw chiller with high-efficiency shell and tube type heat exchanger and aluminum foil with a copper tube air cooled condenser.
As a leading air cooled screw chiller supplier, TopChiller provides a complete range of air-cooled screw chiller from TPAS-ASH series, with cooling capacity from 40Ton to 580Ton/130KW to 1950KW and the chiller temperature control range is +30 to -30.
Besides the standard air-cooled screw chiller control temperature of 7 to 30, TopChiller also has air-cooled glycol screw chiller control temperature below zero from 0 to -30.
Each air cooled screw chiller designed from TopChiller has the following features:
Using world famous brand semi-hermetic screw compressor- Bitzer from Germany and Handbell from Taiwan.
Each screw compressor with 4 steps of energy control 25%-50%-75%-100% to make sure the whole screw chiller is stable and guarantee high refrigeration performance. There are also 2 or 3 compressors for optional depends on the required refrigeration capacity.
Highly efficient closed loop shell and tube type heat exchanger as the evaporator, and using air cooled type condenser-Copper tube sleeve aluminum fin with big volume air cooling fan.
As a leading water-cooled screw chiller manufacturer with almost 20 years of experience since 2003, TopChiller provides a complete range of water-cooled screw chiller from TPWS-WSH series.
The cooling capacity of screw water chiller is from 30Ton to 480Ton/105KW to 1688KW and the chiller temperature control range from +30 to -30.
Besides the standard water-cooled screw chiller control temperature from 7 to 30, TopChiller also has a water-cooled glycol screw chiller control temperature below zero from 0 to -30 for some special industrial applications.
With 20 years experience in design and manufacturing water-cooled screw chiller from TopChiller has the following features:
Using famous brand Semi-hermetic Screw Compressor- Bitzer from Germany and Handbell from Taiwan.
Each screw compressor comes with 4 steps of energy control 0-25%-50%-75%-100% to make sure the whole screw chiller operates when stable with high refrigeration performance.
Each water-cooled screw chiller with high-efficiency shell and tube type heat exchanger and aluminum foil with a copper tube air cooled condenser.
Industrial plc centralized control combined with compressor capacity control system, precisely monitor.
Ry, saving installation time and cost.
W shape aluminum fin type condenser, assuring adequate heat exchanging area within smaller unit size
High efficient evaporator with internal thread copper tube.
Large air volume axial fan with metal blades. Motor separated from net-cover, fixed on exhaust port by metal
Siemens plc control, lcd touch screen interface.
Standard design charged r22, cfc free r407c, r410a, r404a, r134a for option.
380v-415v/50hz 3ph for standard design. Different design on customers' request.
i-hermetic screw compressor. The latest 5 to 6 patented screw rotor profile with excellent efficiency.
Adjustable infinite or closely stepped capacity control, features energy efficient, stable and quiet running.
Most advanced patented highest precision manufacturing process.
Built-in full intelligent monitoring and protection including thermal motor temperature monitoring, phase sequence monitoring, manual reset lock-out, oil temperature sensor.
Wide range of refrigerant for option, including r134a, r407c and r22(r404a, r507c upon request).
Microprogramming control system
Industrial plc centralized control combined with compressor capacity control system, precisely monitor.
Integrated protection for low temperature, high/low pressure, anti-freezing, phase missing, anti-phase, overload, motor over temperature, oil differential, flow switch, start up latency.
Optional operation language, menu leading, unit running state easy to adjust.
Easy installation, reliable running
Closely stepped start-up, minimize impact to electricity.
Steady and safe running, low vibration, easy for installation.
Compact structure, less space demand and light in weight, easy for transport and installation.
Completely wired, inspected and tested pre-delivery, saving installation time and cost.
Evaporative Screw Chiller is also referred to as an Energy-saver chiller with an overall efficiency ratio of 40%~60% when compared to an air-cooled unit the water-cooled unit ratio is about 25%~30%. Bid bye to configuring the cooling tower with this chiller. This feature allows it to save more than 50% of water. Moreover, our reasonable and simple machine is a type of practical novel refrigeration with water equipment.
Evaporative Screw Chiller is also referred to as an Energy-saver chiller with an overall efficiency ratio of 40%~60% when compared to an air-cooled unit the water-cooled unit ratio is about 25%~30%. Bid bye to configuring the cooling tower with this chiller. This feature allows it to save more than 50% of water. Moreover, our reasonable and simple machine is a type of practical novel refrigeration with water equipment.
Key Features:
Programable
Multi compressor combination
Premium quality compressor rack.
Asymmetric screw compressor.
Tubular DX evaporator.
Copper Tube
Efficient heat exchange.
Stable operation.
Less noise.
Enhanced performance
Industrial appearance.
Wide temperature spectrum.
Ultimate power saver
Easy to use.
Compact design and dimensions.
Power supply: 380V/3PH/50Hz
Applications:
Our Evaporative Screw Chiller has a vast range of applications in several sectors. It covers a wide range of activities from food to plastics to ensure that your requirements are met by it.
Water-Cooled Screw Chiller
Screw semi-hermetic compressor, to serve the needs of the equipment or technics cooling each industry. and supply frozen water to central air-conditioning system.
Shell and tube or plate type heat exchanger, with tight structure and small occupation area.
Can select single or more units to modular, modular can include 2-4 units, having greater refrigerating capacity, standby each, interval running.
Microcomputer or plc control.
Can select heat reclamation device.
Temperature control range:3â??-30â??ï¼?
Refrigerated capacity:115KW - 1700KW (50HP-480HP).
Special Industrial Chiller for Industry
For CNC Machine
For Pharmaceutical Industry
For Plastic Uptake Industry
For Plastic Mould Industry
For CD-ROM Manufacturing Industry
For Chemical Coating Industry
For Packaging and Printing Machine
For Laser Cutting Equipment
For Laboratory Equipment
For Electrical Discharge Machine
For Textile Manufacturing
For Electroplating Industry
For Food Industry
For Leather Industry
For Floor Glue Industry
For Leatherette Industry
For Concrete Industry
For Polyurethane Industry
For Die-casting Machine
For Cosmetics and Commodity Industry
For Optoelectronic Industry
Air-Cooled Screw Chiller
Screw semi-hermetic compressor, to serve the needs of the equipment or technics cooling each industry. and supply frozen water to central air-conditioning system.
Shell and tube or plate type heat exchanger, with tight structure and small occupation area.
Can select single or more units to modular, modular can include 2-4 units, having greater refrigerating capacity, standby each, interval running.
Microcomputer or plc control.
Can select heat reclamation device.
Dispense with cooling tower and cooling water pump, convenient install.
Temperature control range:3 -30
Refrigerated capacity:115KW - 636KW (50HP-240HP).
Special Industrial Chiller for Industry
For CNC Machine
For Pharmaceutical Industry
For Plastic Uptake Industry
For Plastic Mould Industry
For CD-ROM Manufacturing Industry
For Chemical Coating Industry
For Packaging and Printing Machine
For Laser Cutting Equipment
For Laboratory Equipment
For Electrical Discharge Machine
For Textile Manufacturing
For Electroplating Industry
For Food Industry
For Leather Industry
For Floor Glue Industry
For Leatherette Industry
For Concrete Industry
For Polyurethane Industry
For Die-casting Machine
For Cosmetics and Commodity Industry
For Optoelectronic Industry
Low-Temperature Screw Chiller
To serve the needs of the equipment or technics low temperature cooling each industry.
Shell and tube type heat exchanger, tight structure.
Can select single or more units to modular, modular can include 2-4 units, having greater refrigerating capacity, standby each, interval running.
Microcomputer or plc control.
Can select heat reclamation device.
Temperature control range: -35 -5
Refrigerated capacity:115KW - 636KW (50HP-240HP).
Special Industrial Chiller for Industry
For CNC Machine
For Pharmaceutical Industry
For Plastic Uptake Industry
For Plastic Mould Industry
For CD-ROM Manufacturing Industry
For Chemical Coating Industry
For Packaging and Printing Machine
For Laser Cutting Equipment
For Laboratory Equipment
For Electrical Discharge Machine
For Textile Manufacturing
For Electroplating Industry
For Food Industry
For Leather Industry
For Floor Glue Industry
For Leatherette Industry
For Concrete Industry
For Polyurethane Industry
For Die-casting Machine
For Cosmetics and Commodity Industry
For Optoelectronic Industry
1. High Efficiency
The units can be equipped with heat recovery. If using as air-conditioning, the recovery heat will be 30% -80% of the total cooling capacity. The temperature of hot water can reach 70 degrees.
While using recovery heat the unit efficiency can be increased 5%.
2. Running stable
It has 7 safe protection functions to ensure the unit running normally.
With double compressors installed, if one compressor malfunction, the other compressor will keep working properly.
3. Intelligent management
Visual touch screen control system makes operation very easy. timely feedback for various of malfunction information.
The control system can be connected with users central control system, then customers can monitor the running status of the unit at any time.
4. Easy installation and maintenance
The units are filled with refrigerant and lubricant before delivery, customers only need to connect the inlet pipe, outlet pipe and power to run.
The control interface directly display the malfunction contents, its much easier for customers to know and sort out problems.
5. Various of refrigerant to meet customers specific requirements.
Refrigerant: R22.R407CR134a. are optional
22776 Screw Chiller Suppliers
Short on time? Let Screw Chiller sellers contact you.
