Key Features
1.Excellent chemical resistance, low odor, good adhesion
2.Low volatile does not exceed 300ppm, closed environment without corrosion, non-fogging
3. Moisture, dirt and other atmospheric composition proof
4.Relieving the mechanical stress and tension that cased by machinery, heat shock and vibrate
5.Excellent outdoor aging-resistance for 20-30 years
6.Stable mechanical and electrical properties between -60-260;C
Typical Applications
For household appliance, engineering machinery, PV modules, automotive lamps, LED lamps, PCB components fixing bonding and sealing.
Technical Data Table
PROPERTY STANDARD/UNITS VALUE
Before curing SI1336TW/TB SI1336T
Color Visual inspection White/Black Transparent
Viscosity 25;C, mP6;s paste paste
Density 25;C, g/cm3 161;¨¤0.03161;¨¤0.03
Tack free time 25;C, 55%RH, min 61;¨¤5
After cured Room temperature cured
Hardness Shore A 35¡Â¨Â¤#161;¨¤5
Thermal conductivity W/m.K 0.35 0.27
Elongation at break % 320 230
Tensile strength MPa 2.3 1.8
Shear strength MPa, iron/iron 1.8 1.3
Dielectric strength kV/mm, 25;C 22 18
Loss factor 1 MHz, 25;C 0.09
Dielectric constant 1 MHz, 25;C 2.9
Volume resistance (DC500V6; cm 611014
Product Introduction
Ausbond® 181 series is a kind of organic silicon rubber which is half of flowing, single component, curing at room temperature, is medium curing, causes cross bonding by condensation reaction among water in air, form high-quality
elastomer.For most metals, a plastic is non-corrosive and excellent adhesion. Against alternating cold and heat, aging condition and dielectric protective, shockproof, damp-proof, water resistance, corona-resistance and leakage
resistance. It is fully accepted by the requirements of the EU ROHS.It can conform to the requirements of EU ROHS Directive completely.
Typical Purposes
1.Used in sealing, splicing and fixing among electronic product, Instruments and electronic component on electrical equipment, in sealing, splicing among mini-electric appliance, electron.
2. It is an excellent product for waterproof, splicing and sealing on the both ends of LED; sealing soft LED.
3. Splicing and sealing among engineering plastics or between coil and power's plastic shell and so on.
Package Specification
100ml/piece, 100 pieces/case; 300ml/piece, 24
pieces/case.
Storage and Transport
1. Store in the cool and dry place, with shelf life 9 months (25¡æ).
2. This product belongs to non-dangerous articles please transport it as general articles.
General purpose silicone sealant is a one part, fast curing and permanently flexible silicone sealant. With excellent waterproof performance, it is also a type of anti-fungal sealant able to use in bathroom and kitchens. Excellent tensile strength and compression restoring ability. Strong adhesion to glass, pvc, ceramic, concrete, wood, metal, tiles, vinyl and most building material.
Typical applications:
1 al-alloy door & window , general decoration caulking seal.
2 all kinds of glass curtain wall , aluminum-plastic plate curtain wall.
General Purpose Acetic silicone sealant Product Features Acetic cureing , quickly curing, excellent adhesion Excellent resistance to low and high temperature change Good anti-aging propetry Main Appplication All kinds of glass engineering bonding and sealing. Used for bonding various glass cabinets Storage 12 months under dry codition ,blow 27 Package 260ml/300ml 24 pieces per carton
19819 Rtv Silicone Sealant Suppliers
Short on time? Let Rtv Silicone Sealant sellers contact you.
100% RTV silicone sealant, waterproof silicone sealant
Kali5000
Dow Corning GP Quality
Property:
One part silicone;
100% Dow Corning GP Quality;
Acetic curing and solidified;
Fast dry;
High intensity and tightness;
Resistant to water, weather, ultraviolet, ozone etc.Use:1. Professional sealant for glass, glass device, big glass sheet;2. Good for sealing among plastic-glass, aluminum-glass, glass-glass etc;3. Seal & cementation of al-alloy door & window, storefront, show window, diagonal and skylight corner line; 4. Good sealing performance for glass, glass fiber, pottery & porcelain and greaseless material
Available colors:
white, black
Package:
35gr, 50gr, 70gr, 85gr blister tube;
280ml, 300ml, 310ml hard cartridge;
200L drum bulk material
Shelf life: 12 months after production date
Notes: we Kater can accept OEM production, and can do buyer's brand, logo and design.
Part I: 190L Part II: 19L About 72 sets/20' Container
Key Features
1.It has a high thermal conductivity
2.Excellent comprehensive properties, elasticity, non-yellowing, no bleed oil
3.Moisture, dirt and other atmospheric composition proof
4.Relieving the mechanical stress and tension that cased by machinery, heat shock and vibrate
5.Good corona resistance and electrical insulation performance
6.Excellent outdoor aging-resistance for 20-30 years
7.Stable mechanical and electrical properties between -60- C
Typical Applications
Used for sealing LED lamps, thermal dissipation of auto electrical components, PCB and other heat dissipation components. Gap filling between power transistor, diode thyristor and substrates.
Technical Data Table
PROPERTY STANDARD/UNITS VALUE
Before curing SI1316 SI1317
Color Visual inspection White
Viscosity 25 227;C, mPa 8226;s Paste
Density 25 227;C, g/cm3 1.65 2.25
Tack free time 25 227;C, 55%RH, min 2~5 2~5
After cured
Hardness Shore A 50 1615
Thermal conductivity W/m.K 0.82 1.50
Elongation at break % 150 100
Tensile strength MPa Y1
90 Y2
Shear strength MPa, iron/iron Y1 Y2
Dielectric strength kV/mm, 25 227;C 20 20
Loss factor 1 MHz, 25 227;C 0.09 0.09
Dielectric constant 1 MHz, 25227;C 2.9 2.9
Volume resistance (DC500V) | 8226; cm 2.01014
2.0 1014
SI1316. 310ml/tube, 25 tubes/carton; 100ml/tube, 100 tubes/carton.
SI1317. 310ml/tube, 25 tubes/carton
Definition
Silicones are synthetic polymer containing alternate silicone and oxygen atoms as its backbone. Silicones are made from silicon (a metal obtained from silica sand) and methyl chloride (an organic compound) in a process known as the direct process. The Silicone sealant in the uncured state normally looks like a thick paste or cream. After curing the paste turns into an impressive rubber.
Applications
Silicone sealant are used as a form-in-place gaskets for engine & transmission applications, sealing of exterior joints, aquarium joints bonding, sealing of bath tubs, construction and glazing application, electrical potting & encapsulation, mould making, etc.
Curing Mechanism
RTV silicone systems use humidity or moisture in the air during curing and cannot be accelerated using heat (excessive heat in the curing process can be detrimental). Small amounts of by-product are also produced. The cure process will only take place if the material is open to the atmosphere and curing will be adversely affected if access to humidity is removed prior to the completion of the cure process.
Provided product types
One component RTV silicone sealant
Two component RTV silicone sealant
Packing, storing, shelf life and transport
Available packing sizes vary from 25 g to 25 kg, packed in lacquered coated aluminium tubes, HDPE cartridges and epoxy coated MS drums. Store products at room temperature (20C to 35C). Shelf life can vary from 4 - 12 months. They are safe to transport by road, air and sea.
We are a leading supplier of electroplating chemicals, industrial polishing and welding consumables, water treatment, powder coating, fertilizers. We stock and carry an extensive range of ready to use chemicals. We deal with so many different chemicals and we would like you to contact us for more information about our different chemicals and products.
RTV Silicone anti-mildew sealant is used as general adhesive/sealant indoor and outdoor, suitable for:
1. Kitchens, baseboards, walls and tiles,sinks(washbasin), bathtub, closet combination and cracked places
2. Showers, lavatories, bathtubs and floors
3. Bathroom fixtures, fiberglass spa units
4. Refrigerator and freezer liners (however, not FDA-approved for food-contact application)
5. Sealing, bonding and repairing other construction materials including aluminum,marble and coated glass
6.Automobile sound proof, dust and water insulating.
280 or 300ml/pc,plastic cartridge
24 pcs/case
OUTER CARTON MEAS. 31X20X24cm
ONE 20'GP CAN CONTAIN 1900 CTNS.
iFixes i704 RTV Silicone Rubber Sealant Glue features thermal conductivity, strong adhesive and insulation, suitable for electronic components and CPU heat dissipation, fast repair of electronic product PCB boards, electronic components, CPU chips, etc.
Features:
1. Strong adhesion and good sealing performance.
2. Waterproof and moisture-proof, insulating, resistant to electricity, high and low temperature.
3. Insulation, arc resistance, sealing and leakage prevention, can be used for insulation, sealing and leakage prevention of electronic components, power strips and other electrified products.
4. After curing, silicone sealant can work normally in various harsh environments, improve the stability of the equipment, and resist high and low temperatures.
5. Use a long-tail rubber dropper, which is convenient, fast and accurate in applying rubber.
6. Black and White two colors are available.
7. It is widely used in the bonding and sealing of electronic components, semiconductor materials, electronic and electrical equipment, waterproof sealing of instruments and meters, potting of electronic components, etc.
Please note that paste glue can only be sent by special way (usually economy mail).
NEXO SEALS Weather Proofing Sealant is designed for sealing expansion and control joints, precast concrete panel joints, on structural curtain wall mullion joints, stress cracks, tiles/granite joints etc.
ADVANTAGES:- 1. All weather applicability. 2. Good bonding without primer and good joint movement. 3. Long life under all weather conditions.
Colour - Black, White, Grey
URJA FIRESTOP SEALANT is developed for sealing applications in various areas (COMMERTIAL OR GROUPED RESIDENTIAL CONSTRUCTION) and in any FIREPRONE areas. URJA FIRESTOP SEALANT can be used in systems where dynamic movement is expected: plumbing; HVAC; bath and dryer vents; metallic pipes; non-metallic pipes, conduits and tubing; insulated pipes; electrical and electronic cabling; concrete, gypsum, metal ductwork; wood floors.
URJA FIRESTOP SEALANT is a fast setting, elastomeric compound designed as a joint sealant for high velocity air conditioning
ducts installed indoors. It may be used with or without reinforcing tapes. It has a mild "paint tape" odor and applies cleanly without stringing. Mechanically fasteners of the type and number normally used for duct assemblies are required to provide rigidity to the duct system.
SPECIAL FEATURES:
Zero percent VOC · Totally Eco- friendly product. ï?· Specially developed for green building projects.
Releases only water vapor
