We at BDMG, offer high quality PTFE Teflon wires for complex, high density wiring packages and cater to the necessity of top-notch electrical properties, small size and low weight.
PTFE Teflon Wires are also suitable for general industrial applications where a wide range of operating temperatures (-60 C to +260 C) may be experienced together with exposure to corrosive chemicals.
Some of the Key Specifications are mentioned below:
Categories: Unscreened, Screened, and Sheathed.
Voltage grades: 250 V R.M.S., 600 V R.M.S. and 1000 V R.M.S.
Conductor: Silver Plated Copper (SPC)
Single or stranded, sizes from AWG 10 to AWG 32.
Current carrying capacity: 6 Amps to more than 100 Amps
Cross sectional area of conductor: 0.031 mm square to 4.650 mm square.
Standard Sizes of PTFE Wires as per BSG-210 Type A, B, C and MIL-W-16878 Type ET, E, EE.
Non-standard and large cross sectional sizes are made to order.
PTFE/Teflon sheet can be made by skived and molded techniques, so both skived PTFE(teflon) sheet and molded PTFE(teflon) sheet can be offered. Meanwhile, we can use virgin, recycled or mixed PTFE material to make PTFE sheet according to customers' different demands. As PTFE has a very low co-efficient of friction, the surface of PTFE sheet has similar friction levels to ice. PTFE can work at -180 C ~+260 C and is the best electrical insulator of all known plastics.
PTFE sheet can be used as lining, seal components, wire isolation, slide block, gasket, seal, dielectric material, etc.
Remarks:
We can also produce PTFE(Teflon) sheet in other sizes and thickness according to customers' specific requirements.
Length(mm) x Width(mm)Thickness(mm)
NorminalTolerance
150 x 1501.0-30¡À0.30 ~ ¡À0.50
250 x 2501.5-30¡À0.30 ~ ¡À0.50
300 x 3001.5-30¡À0.30 ~ ¡À0.50
450 x 4501.5-30¡À0.30 ~ ¡À0.50
600 x 6002-30¡À0.30 ~ ¡À0.50
800 x 8003-30¡À0.30 ~ ¡À0.50
1000 x 10003-30¡À0.30 ~ ¡À0.50
1200 x 12003-30¡À0.30 ~ ¡À0.50
1000 x 20005-30¡À0.30 ~ ¡À0.50
1500 x 15005-30¡À0.30 ~ ¡À0.50
1800 x 18008-30¡À0.30 ~ ¡À0.50
2000 x 20008-30¡À0.30 ~ ¡À0.50
5366 Ptfe Teflon Suppliers
Short on time? Let Ptfe Teflon sellers contact you.
PTFE/Teflon rod can be made by extruded and molded techniques, so both extruded PTFE(teflon) rod and molded PTFE(teflon) rod can be offered. Meanwhile, we can use virgin, recycled or mixed PTFE material to make PTFE rod according to customers' different demands. As the material of PTFE has a very low co-efficient of friction, so the surface of PTFE rod has similar friction levels to ice. The material of PTFE can work at -180 C ~+260 C and is the best electrical insulator of all known plastics.
Extruded teflon PTFE rod can be used as lining, seal components, wire isolation, slide block, gasket, seal, dielectric material and so on.
Remarks:
We can also produce PTFE(Teflon) sheet in other sizes and thickness according to customers' specific requirements.
PTFE/Teflon tube can be made by extruded and molded techniques, so both extruded PTFE(teflon) tube and molded PTFE(teflon) tube can be offered. Meanwhile, we can use virgin, recycled or mixed PTFE material to make PTFE tube according to customers' different demands. As the material of PTFE has a very low co-efficient of friction, so the surface of PTFE tube has similar friction levels to ice. The material of PTFE can work at -180 C ~+260 C and is the best electrical insulator of all known plastics.
PTFE tube can be used as wire and cable jacket, inner lined pipes for corrosive fluids and used in hydrochloric acid heat exchanger, etc.
Remarks:
We can also produce PTFE/Teflon tube in other diameters and lengths according to customers' requirements.
PTFE plastics has excellent corrosion resistance, aging resistance, high and lowtemperature resistance, good lubrication and insulation, non-adhesiveness harmless.It is widely used in industries, such as aviation, chemical industry, electricand electronics, bridge, mechanical manufacturing, textile, paper making andceramics.
Product DescriptionTurning PTFE Board is commonly known as plastic King, F4, or Teflon. The suspension PTFE resin can be made into sheet metal, turning film and tube by molding. Can be pressed to push the molding. can be mixed with graphite, such as plate, rod, packing, rope, raw materials belt.APPLICATION:Seals/washers, ring materials, wear-resistant plate/seat power, insulating parts, anti-corrosion industry, mechanical parts, lining, oil and natural gas, petrochemical industry, Chemical industry, instrument and equipment manufacturers.Product Specificationlength*widthThickness mmNominal Tolerance150*150 mm0.3-100 mm±0.3~±0.5250*250 mm0.3-100 mm±0.3~±0.5300*300 mm0.3-100 mm±0.3~±0.5500*500 mm0.3-100 mm±0.3~±0.5600*600 mm0.3-100 mm±0.3~±0.5700*700 mm0.3-100 mm±0.3~±0.5800*800 mm0.3-100 mm±0.3~±0.51000*1000mm0.3-100 mm±0.3~±0.51200*1200mm0.3-100 mm±0.3~±0.51500*1500mm0.3-100 mm±0.3~±0.52000mm*2000mm0.3-100 mm±0.3~±0.5We can customize the product according to the customer's requirement.Details of PTFE filled with other materialsFilled materialsCommon filled ratio (Quantity %)Main performances Bronze40, 60Increases hardness and wear resistance; Increases dimensional stability and compressive strength;Carbon5, 10, 15Increases compressive strength, hardness, wear, and load properties. Good chemical resistance;Improves electrical properties.Graphite5, 10, 15Improves the deformation under load; Reduces initial wear; Improves thermal and eletrical conductivityGlass Fiber10, 15, 25Increases compressive strength, rigidity and wear. Reduces creep and cold flow; Improve Dimensional Stability.Carbon Fiber10 , 15, 25Increases compressive strength, hardness, wear, and load properties. Reduces creep and cold flowPOB (polyphenyl ester)5, 10, 15Improve the lubrication performance;Enhance the mechanical strength;Increase using temperatureBaSO45, 10, 15Increases compressive strength, hardness and wear resistance Reduces creepSiO25, 10, 15Increases hardness and wear resistance; Improve Dimensional Stability.Glass beads5, 10, 15Reduces creep and cold flow;Lower density Increases hardness and wear resistance;Others materialsPEEK(polyetheretherketone), PI(Polyimide), MoS2 are also okRemarksSome materials have similar enhancement effect, but degrees of enhancement are different. And they have different prices. More details please contact us.Product PackagingPacked by plastic bags,put into Plywood cases that don't need fumigation. Other packing is customized according to client's requirements.Company Profile
PTFE Teflon Tape1. Low density 0.2g/cm3 PTFE Teflon Tape is ideal for systems with water,drinking water and compressed air. Max. pipe diameter: 3/4". Temperature resistant from -200C to +80 C. Max. pressure: 10 bar.2. Miduim density 0.35g/cm3 PTFE Teflon Tape is ideal for systems with drinking water and air. Max. pipe diameter: 3/4". Temperature resistant from -200C to +100C. Max. pressure: 20 bar.3. Miduim density 0.6g/cm3 PTFE Teflon Tape is Ideal for steam. Economical in use. Pipe diameter: 3/4 - 2. Recommended temperature range from -200C to +160C.4. Density 0.7g/cm3 PTFE Teflon Tape is ideal for steam. In addition, ideal for most chemicals, acids, bases, solvents, etc. Max. pipe diameter: 11/4". Max. pressure: 30 bar. Also useful for hydraulics. Temperature resistant from -200 C to +180 C.5. High density 1.0g/cm3 PTFE Teflon Tape is approved for gas and drinking water and is ideal for hydraulics. Temperature is resistant from -200 to +260.6. Density 1.1g/cm3 PTFE Teflon Tape is for systems where requirements for quality and safety have high priority. It is very strong and economical in use. It is less suitable for fine thread. Temperature resistant from -200 to +260. 7. Density 1.3g/cm3 PTFE Teflon Tape is Ideal for use in situations where there are high requirements for e.g. acid-resistance, pressure or heat. This product is very diffusion-proof and is therefore highly suitable for oil, petrol and diesel. APPROVED for gas and drinking water (EN 751-3 and DIN 30660). Otherwise same use as for other high-density tapes. Temperature resistant from -200 C to +260 C.1.Different colors could be offered. And we could produce 200000 rolls per day. So the quantity and quality could be guaranteed.2.PTFE Tape is packed with carton case and OEM is available3.We put your order into our tight production schedule, ensure your punctual delivery time.Q: How to know the quality of ptfe thread seal tape A: In general, the quality of ptfe tape depends on the toughness and the color. Higher the toughness and purer the color, better the quality.Q: How about your packing A:Our general packing is 10pcs/shrink,250pcs/inner box,500pcs or 1000pcs/cartonIf you have your own packing,we can make it based on your requirement.FUJIAN BLEA SEA INDUSTRIAL CO.,LTD is specialized in manufacturing faucet,angle valve,plumbing hose,floor drain,drainer,ptfe thread seal tape and other sanitary ware productions.Now we have 2 factories with more than 200 employees,covering an area of 20,000 square meter construction area.our market is in Europe,Middle East, Eastern Europe,South America,Southeast Asia,South Asia,North Africa and other countries and area.
Material characteristics:
1, white, odorless, tasteless, non-toxic powder, commonly known as "plastic king".
2, the active hydrogen atoms on the ethylene monomer are replaced by inert fluorine atoms, and the polytetrafluoroethylene monomer is polymerized.
3, temperature resistance, the operating temperature of -100â??-250â??.
4, high strength weather resistance, radiation resistance and low permeability.
5, non-adhesion, is the smallest surface tension in solid materials, does not adhere to any substance.
6, non-toxic, with physiological inertia, as artificial blood vessels and organs long-term implantation in the body without adverse reactions.
PTFE seamless sealing belt is made of high tensile fiberglass or Kevlar knitted by special equipment and coated with fine PTFE. It can overcome former problems of traditional joint fusing machine belt such as bad stability, ruptures, and deflecting for different girth on two sides at the joint. The using life is much longer than all kinds of PTFE fusing machine belt with joint. Features : 1)High temperature resistance and adherence resistance; 2)Good tensile strength, preventing deflecting; 3)Excellent capability of resistance of static; 4)Smooth surface, more suits for super thin lining; 5)Flex fatigue resistance, durable, long using life. 6) Good abrasion resistance. Specificationsï¼? Item NO. Girth(mm) Thickness HY-S75 750 0.20mm HY-S77 770 0.20mm HY-S81 810 0.20mm HY-S100 1000 0.20mm HY-S101 1010 0.20mm HY-S102 1020 0.20mm HY-S112 1120 0.20mm HY-S115 1150 0.20mm HY-S171 1170 0.20mm
Aokeray ptfe tubing heatshrinktubesNET manufacturer from PTFE/FEP/PFA tube PTFE Teflon Insulated Tubing ,PFTE RAW MATERIAL is FROM most commonly known as DakiN a brand name .USE ON sleeve bearings, push-pull cables, non-stickroller covering etc Control Cable Assemblies ,Motorcycle Cables PTFE TUBING ,ptfe lined tubing. Car cable high temp Teflon liner ,MOTORCYCLES Cable,Hydraulic clutch, brake and oil,Clutch and brake fluid, oil transfer .PTFE hose is specified in many of the most challenging industrial applications such as those found in steel mills, foundries, transit trucks and buses and air compressors..It is also an ideal choice for vacuum/steam lines, spray paint, marine/military, aerospace, biomedical,chemical processing, industrial adhesive, paper mill.The extruded PTFE tube has excellent flex life, high temperature tolerance and superior chemical resistance.QCSS PTFE hose working temperature range is -70 to 260 degree. A reinforcement 304/316 stainless steelwire cover adds strength and durability to withstand high working pressures and harsh environments.Burst pressure reaches to 12,000 psi.Production under ISO 9001:2008 and CE control. High quality product and customer'ssatisfaction is our pursuit. Good faith cooperation. Bright future.40°C and 260°C. Applications: For transfer of high purity products, chemicals, dairy and cosmetic products. Also suitable for heat exchangers and as protective sleeve for cables. They have excellent heat resistance, viscosity, chemical resistance, electrical insulation, etc,we also help custom like annealing, beveling, bonding, printing, marking, tipping, punching, flaring ect. .Aokeray ptfe tubing,heatshrinktubesNET
PTFE is a material of remarkable properties; non-stick, friction-free, self-lubricating, non-wetting, non-flammable, non-brittle, non-toxic, resistant to atmospheric conditions, resistant to fungus growth and resistant to all chemicals (except molten alkali metals and fluorine at elevated temperatures and pressures). Its electrical properties are equally outstanding. All properties are maintained over a wide working temperature range of -200 Celcius. to + 360 Celcius.
5366 Ptfe Teflon Suppliers
Short on time? Let Ptfe Teflon sellers contact you.
