HDPE silicon-core pipe is a kind of communication optical (electric) cable protection tubing, which is produced and shaped through extruding synchronistically the silicon-core material with low friction coefficient inside HDPE pipe. Thus the HDPE silicon-core pipe provides the convenience for the cable laying because of the lubricating solid tunnel with durability and lower frication coefficient. It becomes the most advanced optical cable protection in world at present. Its advancement is presented on the replacement of cable personal pulling. The cable-blowing machine will blow the cable into the lower friction HDPE pipe and the cable goes forward at high speed in the suspension state. This cable laying way avoids the cable damages caused by the pulling. The cable blown once can reach more 2000 meters. For that, the accidental signal loss caused by machine pulling has been reduced greatly and the too many knots resulted from the pulling length limitation has been decreased greatly. At the same time, the well digging quantities have been minimized and the project cost has been saved. The HOPE silicon-core pipe has the high intensity, excellent property resisting high or low temperature, adaptability for steepness and bending changes.
Nominal(internal/external diameter):26/32mm,28/34mm,33/40mm,38/46mm,42/50mm,50/60mm etc.
PRODUCT INTRODUCE:
HDPE silicon core pipe is a kind of novel composite pipe wall with silica gel mass solid lubricant.
By three plastic extruding machine synchronous extrusion compound, main raw materials for high density polyethylene, core layer to the lowest friction coefficient solid lubricant silica gel quality.The widely used optical cable communication network system.
PRODUCT CHARACTERISTICS:
The lining of the silicon core layer is solid, permanent lubricant;
The lining of the silicon core layer is pressed by synchronization in high density polyethylene pipe wall, and evenly distributed throughout the pipe wall, not peeling off.
The lining of the silicon core layer and high density polyethylene with the same physical and mechanical properties;
Internal friction characteristics of silicon core layer remains the same, cable in the pipe can be extracted repeatedly, blowing method, one can blow cable > 1000 m or above;
The lining of the silicon core layer does not react with water, wash water pipe after an accident.
Ferro silicon Specs: Si:75%min. and Si:72%min. C:0.2%max. S:0.02%max. P:0.04%max. Al:2.0%max.1.5%max.and 1.0%max .Commodity: Ferro Silicon Low Al Specs: Si:75%min. C:0.2%max. S:0.02%max. P:0.04%max.Al:0.1%max.0.3%max.and0.5%max. In 1mt plastic woven bags.
Ferro Silicon Ferro Silicon has a melting point of 1200�¯�¿�½?�?�°C to 1250�¯�¿�½?�?�°C with a boiling point of 2355�¯�¿�½?�?�°C and Ferro Silicon contains about 2% of calcium and alluminium. Ferro Silicon, as an additive to the production process of ferrous metals, will impart several desirable properties upon the resultant alloy. Some of the primary benefits of adding Ferro Silicon to an alloy is to improve the corrosion resistant properties of the new compound, as well as to add to the high temperature heat- resistance properties of the new alloy, for example, in the production of silicon steel for use in transformer cores.
FerroChrome is a kind of Ferro alloy which is formed by Ferro and Chrome,it is an important alloy addition in steel making. Ferrochrome (Fe Cr) is an alloy of chromium and containing between 50% and 70% chromium.
98511 Hdpe Silicone Core Pipe Suppliers
Short on time? Let Hdpe Silicone Core Pipe sellers contact you.
HDPE Silicon Pipe
HDPE silicon core pipe is a new type of composite pipe with silicone solid lubricant on the inner wall, referred to as silicon pipe. Three plastic extruders are used for simultaneous extrusion and compounding.
Product Description
HDPE silicon core pipe is a new type of composite pipe with silicone solid lubricant on the inner wall, referred to as silicon pipe. Three plastic extruders are used for simultaneous extrusion and compounding. The main raw material is high-density polyethylene, and the core layer is made of solid lubricant silica gel with the lowest friction coefficient. Widely used in optical cable communication network systems.
Features
The silicon core layer on the inner wall is a solid, permanent lubricant;
The silicon core layer on the inner wall is simultaneously squeezed into the high-density polyethylene pipe wall, and is evenly distributed across the inner wall of the pipe without peeling or detaching, and has the same life span as the silicon pipe;
The silicon core layer on the inner wall has the same physical and mechanical properties as the high-density polyethylene;
The friction characteristic of the inner silicon core layer remains unchanged, and the cable can be drawn repeatedly in the pipeline;
The silicon core layer on the inner wall does not react with water, and water can be used to flush the pipeline after an accident.
HDPE Silicon Pipe
HDPE silicon core pipe is a new type of composite pipe with silicone solid lubricant on the inner wall, referred to as silicon pipe. Three plastic extruders are used for simultaneous extrusion and compounding.
Product Description
HDPE silicon core pipe is a new type of composite pipe with silicone solid lubricant on the inner wall, referred to as silicon pipe. Three plastic extruders are used for simultaneous extrusion and compounding. The main raw material is high-density polyethylene, and the core layer is made of solid lubricant silica gel with the lowest friction coefficient. Widely used in optical cable communication network systems.
Key Features
The silicon core layer on the inner wall is a solid, permanent lubricant;
The silicon core layer on the inner wall is simultaneously squeezed into the high-density polyethylene pipe wall, and is evenly distributed across the inner wall of the pipe without peeling or detaching, and has the same life span as the silicon pipe;
The silicon core layer on the inner wall has the same physical and mechanical properties as the high-density polyethylene;
The friction characteristic of the inner silicon core layer remains unchanged, and the cable can be drawn repeatedly in the pipeline;
The silicon core layer on the inner wall does not react with water, and water can be used to flush the pipeline after an accident.
HDPE Silicon
HDPE silicon core pipe is a new type of composite pipe with silicone solid lubricant on the inner wall, referred to as silicon pipe. Three plastic extruders are used for simultaneous extrusion and compounding.
Product Description
HDPE silicon core pipe is a new type of composite pipe with silicone solid lubricant on the inner wall, referred to as silicon pipe. Three plastic extruders are used for simultaneous extrusion and compounding. The main raw material is high-density polyethylene, and the core layer is made of solid lubricant silica gel with the lowest friction coefficient. Widely used in optical cable communication network systems.
Key Features
â?? The silicon core layer on the inner wall is a solid, permanent lubricant;
â?? The silicon core layer on the inner wall is simultaneously squeezed into the high-density polyethylene pipe wall, and is evenly distributed across the inner wall of the pipe without peeling or detaching, and has the same life span as the silicon pipe;
â?? The silicon core layer on the inner wall has the same physical and mechanical properties as the high-density polyethylene;
â?? The friction characteristic of the inner silicon core layer remains unchanged, and the cable can be drawn repeatedly in the pipeline;
The silicon core layer on the inner wall does not react with water, and water can be used to flush the pipeline after an accident.
HDPE Silicon Pipe
HDPE Silicon Pipe also known as HDPE silicon core pipe is a composite pipe designed primarily to protect and install optical and electrical cables It features a unique construction where highdensity polyethylene HDPE forms the outer layer while the inner wall is lined with a silicone solid lubricant
Product Description
HDPE Silicon Pipe also known as HDPE silicon core pipe is a composite pipe designed primarily to protect and install optical and electrical cables It features a unique construction where highdensity polyethylene HDPE forms the outer layer and the core layer is made of solid lubricant silica gel with the lowest friction coefficient Three plastic extruders are used for simultaneous extrusion and compounding Widely used in optical cable communication network systems
Features
The silicon core layer on the inner wall is a solid permanent lubricant
The silicon core layer on the inner wall is simultaneously squeezed into the highdensity polyethylene pipe wall and is evenly distributed across the inner wall of the pipe without peeling or detaching and has the same life span as the silicon pipe
The silicon core layer on the inner wall has the same physical and mechanical properties as the highdensity polyethylene
The friction characteristic of the inner silicon core layer remains unchanged and the cable can be drawn repeatedly in the pipeline
The silicon core layer on the inner wall does not react with water and water can be used to flush the pipeline after an accident
We are a leading supplier of electroplating chemicals, industrial polishing and welding consumables, water treatment, powder coating, fertilizers. We stock and carry an extensive range of ready to use chemicals. We deal with so many different chemicals and we would like you to contact us for more information about our different chemicals and products.
Origin:Unites States
Code: 2025820BN
Material: HDPE pipe PE4710 shredded Black
Category: HDPE
Type: pipe PE4710 shredded
Color: Black
Quantity:36 Tons
Loading weight: 18 Tons
Specification:"HDPE pipe PE4710 shredded black
MFI: 0.3
Unwashed. But clean. No dust, no oil.
Sizes are 0.5 inch to 1.5 inch
PE4710 and PE100 are both grades of high-density polyethylene (HDPE), but PE4710 is derived from PE100 and offers higher performance, particularlyin pressure applications. PE100 has similar or lower physical property requirements than PE4710, while PE4710 has stricter design factors andadditional performance requirements.
Key Differences:
Performance Requirements: PE4710 has higher performance requirementsincluding better resistance to slow crack growth (SCG) and rapid crackpropagation (RCP) compared to PE100.
Packing: Jumbo bags
Subject to unsold"
Thanks for contacting us!
We are selling CFR term, Incoterms 2020. Payment term: 50% advance, balance against copy Bill of Lading
Could you please give us more details about your company and demand for us to offer you the suitable material?
1.What is your company name and address?
2.Have you imported this material before?
3.If yes, which is your port of destination and HS code which you use to import this material?
4.How many tons do you need per month?
5.Which grade and color are you looking for?
6.Do you prefer us to contact you via email or whatsapp, wechat, skype,..?
Origin: United States
Code: 2025882BN
Material: HDPE PE100 pipe cutting Black
Category: HDPE
Type: PE100 pipe cutting
Color: Black
Quantity: 16 Tons
Loading weight: 80 Tons
Specification: "HDPE PE100 pipe cutting, PIR
Loading weight 16~20tons/load
Monthly 20loads
Packing bulk into containers
On going shpts"
Thanks for contacting us!
We are selling CFR term, Incoterms 2020. Payment term: 50% advance, balance against copy Bill of Lading
Could you please give us more details about your company and demand for us to offer you the suitable material?
1.What is your company name and address?
2.Have you imported this material before?
3.If yes, which is your port of destination and HS code which you use to import this material?
4.How many tons do you need per month?
5.Which grade and color are you looking for?
6.Do you prefer us to contact you via email or whatsapp, wechat, skype,..?
Origin: United States
Code: 2025820BN
Material: HDPE pipe PE100 shredded Black
Category: HDPE
Type: pipe PE100 shredded
Color: Black
Quantity: 36 Tons
Loading weight: 18 Tons
Specification:"HDPE pipe PE100 shredded black
MFI: 0.3
Unwashed. But clean. No dust, no oil.
Sizes are 0.5 inch to 1.5 inch
Packing: Jumbo bags
Subject to unsold"
Thanks for contacting us!
We are selling CFR term, Incoterms 2020. Payment term: 50% advance, balance against copy Bill of Lading
Could you please give us more details about your company and demand for us to offer you the suitable material?
1.What is your company name and address?
2.Have you imported this material before?
3.If yes, which is your port of destination and HS code which you use to import this material?
4.How many tons do you need per month?
5.Which grade and color are you looking for?
6.Do you prefer us to contact you via email or whatsapp, wechat, skype,..?
Subject: Offer of High-Quality Ferro silicon (Fe Si 72-75%)
Origin: Turkey
MACH TECH Fze is established in Ham riyah Free Zone, Phase I, Sharjah, one of the busiest ports for supply and distribution of various products, globally. We are equipped with one of the largest capacities at a single location and have the ability to supply in bulk. We are one of the biggest trading companies in the private segment. It has more than 1,000 employees , this company is dealing with a number of different industries such as Petrochemical, Oil and Gas, Minerals, pharmaceuticals and food industries in national and international market.it would be great if you visit our website:www.machtechco.com
We are pleased to offer you Ferro silicon 72-75% (Fe Si) with consistent quality and competitive pricing. The product is originated from Turkey, a reliable source well-recognized in the metallurgical supply chain. Product Specification (Typical Analysis):
Silicon (Si): 72% - 75%
Aluminum (Al): <1.5%
Carbon (C): <0.2%
Sulphur (S): <0.02%
Phosphorus (P): <0.03%
Size: 10-60 mm (or as per your requirement)
Packing: 1MT Jumbo Bags or customized
Key Advantages:
Stable quality with guaranteed specifications
On-time delivery from Turkey or Emirate port
Flexible logistics and payment terms
Available stock for prompt shipment
We would be pleased to share a detailed quotation, samples, or further documentation upon your request. We look forward to the opportunity to collaborate with your esteemed company.
We offer superior quality sponge iron that is also known as direct- reduced iron. Our offered sponge iron is made for high grade, 65-70 fe
Min fem-80%, fet-90-92%, s-0.04% max. Loose in form of lumps.
Sponge iron filter material In industry through a sponge iron production equipment is widely applied iron phosphorus reduction method, method of reduction of iron ore concentrate, etc., the rolling iron phosphorus or ore concentrate after reduced iron press down into pieces, into the roasting tube into the kiln roasting, produce the high quality reduced iron. Sponge iron filter material for the first time into the deaerator, must first after backwashing, remove the sponge iron residue on the surface of the filter material float ash impurities.
We are a leading supplier of electroplating chemicals, industrial polishing and welding consumables, water treatment, powder coating, fertilizers. We stock and carry an extensive range of ready to use chemicals. We deal with so many different chemicals and we would like you to contact us for more information about our different chemicals and products.
98511 Hdpe Silicone Core Pipe Suppliers
Short on time? Let Hdpe Silicone Core Pipe sellers contact you.
