S(B) H15 Amorphous Alloy Transformer (10kV, 20kV)
Amorphous Alloy Transformer
Product introduction:
Oil immersed transformer with amorphous alloy core is a new generation of energy-saving product. The iron core is the amorphous alloy material which imported from aboard. Its special advantages is low-load loss. Amorphous alloy transformer is widely used for urban and rural distribution network, especially applicable for the areas and users that pay attention to energy saving.
Product features:
No-load loss
It has the amorphous alloy which is a kind of soft magnetic material with same character in different directions. Its magnetization power is low, resistivity is high and loss of eddy current is low. The no-load loss and no-load current of the iron core used in this kind of transformer is very low. Compared with silicon steel S(B)9 series transformer, the no-load loss decreases about 75% and it decreases about 65%, compared with silicon steel S(B)11. It reduces the operation cost. It is very energy-saving.
S(B)H15-M Series Sealed Amorphous Alloy Power Transformer,oil immersed transformer,oil immersed power transformer,oil distribution power transformer
Oil Immersed Transformer
The transformer is completely hermetical oil-immersed type. The principle is the same as the hermetical power transformer. The basic elements of the amorphous alloy is Iron, nickel, cobalt, boron and carbon etc.
Product Description
The transformer is completely hermetical oil-immersed type. The principle is the same as the hermetical power transformer. The basic elements of the amorphous alloy is Iron, nickel, cobalt, boron and carbon etc. It is a kind of isotropic soft magnetic material with low magnetizing power. With 0.027mm thickness and the filling coefficient is reduced to 0.75-0.8, the amorphous alloy material is very sensitive for stress. The electrical resistivity of the material is 3-6 times of silicon steel sheet and the hardness is 5 times of it.
Load loss of S(B)H15-M 30ï½?1600/6ï½?10 series transformer can be reduced by 15% on the basis of GB/T6451 standard. The no-load loss can be reduced by 70% on the base of GB/T6451 standard. Amorphous alloy transformer meets the standard JB/T10318-2002 Technical parameter of oil immersed type amorphous alloy transformer.
Model and Meaning
Technical Parameter of S(B)H15-M Series Hermetical Amorphous Alloy Power Transformer
Rated capacityï¼?kVAï¼? Voltage and tapping range Connection Group Symbol No-load Lossï¼?Wï¼? Load Loss ï¼?Wï¼?75 No-load current (%) Short-circuit impedanceï¼?%ï¼?
High Voltage (KV) Tapping ranges of High Voltage Low Voltage (KV)
30 66.31010.511 ±5% ±2Ã?2.5% 0.4 Dyn11( or ) Yyn0 130 630/600 2.3 4.0
50 170 910/870 2.0
63 200 1090/1040 1.9
80 250 1310/1250 1.9
100 290 1580/1500 1.8
125 340 1890/1800 1.7
160 400 2310/2200 1.6
200 480 2730/2600 1.5
250 560 3200/3050 1.4
315 670 3830/3560 1.4
400 800 4520/4300 1.3
500 960 5410/5150 1.2
630 1200 6200 1.1 4.5
800 1400 7500 1.0
1000 1700 10300 1.0
1250 1950 12000 0.9
1600 2400 14500 0.8
2000 750 17400 0.20 5
We are pleased to deliver Transformer, Distribution Transformer, Power Transformer, Oil Transformer, Dry Type Transformer. Safe payment and on time deliver time will give you.If you want to know more about the product, please click here.
Raw melting material - aluminum scraps, cans, engine waste etc.
Output capacity - 5-30 tons/h, customized
Automation - Full automatic/ half automatic (based on output requirement and investment budget
Ingot type - ADC12 (7.5kg/ 10kg / customized)
1. After cleaning the oil and grease of waste aluminum, manually put it into the furnace with a forklift;
2. Ignition for melting furnace .Heat up to 680C, and input appropriate proportion of alloy elements. Heat up to 800C, melt and stir evenly, then fetch samples to the spectrometer for testing.
Every lot of production need to do testing .
3. Put A tool that attracts iron into the furnace by forklift, to suck away the iron in the aluminum water.
4. Put the slag agent into Alu liquid to remove the slag. After slag removed , put the slags into Aluminum ash separation machine , and let the aluminum water and ash separate. The proportion of slag agent and aluminum liquid is 1:500
5.Open the drain valve and the aluminum water flows automatically to the ingot production line After the ingot casting is completed, the ingot stacking robot will stack the ingots, which means the production is completed.
three phase double winding amorphous alloy transformer
- Extremely Low Loss, Energy-Saving Features, High Power Consuming Efficiency;
ã??ã??- Amorphous Metal Materials are advantageous in that: They just need to consume lesser energy in material manufacture and with their extremely low losses, power is saved in a large sum, thereby greatly reducing the power plant output, or relatively lowering waste gas (CO2, SO2) emission, lessening both environmental pollution and greenhouse effects, and realizing a maintenance free and contamination free state;
ã??ã??- Low in Operating Temperature, Tardy in Insulation Aging, and Long in Transformer Life;
ã??ã??- High Overload Capacity, High Mechanical Strength;
ã??ã??- Amorphous Cores are featured in that: When a magnetic flux pass through amorphous cores in a rather high frequency, these amorphous cores may remain a low iron loss and a low exciting current, which may not result in core saturation. Consequently SBH15 amorphous alloy transformers made from amorphous cores possess a rather fine resistance to harmonic waves;
Amorphous alloy transformer
Place of Origin: Shandong, China (Mainland)
Brand Name: Juneng or customized
Model Number: SH15
Usage: Power
Phase: Three
Coil Structure: toroidal
Coil Number: two windings
certificate: ISO9001 ISO14001 OHSAS18001
voltage ratio: 10/0.4 11/0.4 6/0.4
damp-proof method: full sealed
cooling method: ONAN
iron core: amorphous alloy
frequency: 50 HZ
winding: duplex winding
Packaging Details:Main body in nude and the accessories packing in seaworthy standard wooden case or according to the requirement of customers.
Delivery Detail:usually within 30 days after the deposit
Description of Amorphous Alloy Transformer:
Amorphous alloy transformer is a new energy-saving and environment-friendly product, recently launched by our company based on market
needs.SH-15 amorphous alloy transformer is made by amorphous alloy cores. They are rolled into the shape of three-phase and five-column, thus result the height of this type of transformer is lower than the three-phase and three-column transformer. What's more, the vacuum oil injection technology greatly improves the insulation level of the transformer. Low-voltage winding generally adopts cylindrical structure by copper foil winding except a small capacity using copper wires.High-voltage winding adopts multilayer cylindrical structure, it makes the distribution of ampere-turns is balanced and the magnetic flux leakage is small. The high and low voltage coils are winded by wire tension device.They are then shaped by press-fitting, This enhances the ability of intensity and anti-short circuit. And we use the mounting plate when assembling the transformer, this increases the reliability. As for the tank
structure and protector, etc, are similar to the whole sealed oil-immersed distribution transformer.
Due to the special magnetic features of amorphous alloy material,the product technical performance indicators have reached the advanced level among the similar products in China at present. So it can replace the silicon steel core transformer, and be used in the distribution networks of outdoor or indoor. Meanwhile, because of the using of a fully-sealed structure, the insulating oil and insulating medium can't contact with air,So it can be operated under any environmental conditions, and is an ideal distribution equipment in urban and rural distribution networks. The no-load loss of this transformer is only about 30% of the S11 transformer with the same capacity. Compared with S9 transformer of the same capacity, the no-load loss decreases about 75%, the no-load current falls about 80%.
User's operating costs can be greatly reduced, and the social and economic benefits are excellent.
Advantages of Amorphous Alloy Transformer:
1.Amorphous metal transformer with alloy cores
2.High level of insulation
3.High mechanical strength, strong ability to withstand short circuit, safe and reliable operation
4.High adaptability to any environment
5.Significant energy-saving effect
6.Low noise, easy installation
Transformers,Distribution and Power Transformer,Varivolt
Safety Transformers
Diesel Generators
Industrial Panels
Stabilizers
Energy Saver
Industrial Panels
We are glad to propose 500 MT of stain less steel mill scale.
Mill scale is formed on the outer surfaces during by the hot rolling lamination of stainless-steel products.
At a visual inspection the material is a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in colour, but it also contains considerable alloying elements such as chromium and nickel.
The recovery ratio after melting in furnace for the most valuable alloy elements is:
- Ni: 3.5 - 4.5%
- Cr: 6-8%
From the chemical and physical analysis performed on the scrap, and according to the European environmental rules, the material has been classified as a special non dangerous waste, listed in green list. In particular the mill scale can be classified as follows:
Waste code: 10 02 10
The material is stored on cemented flooring, and it can be loaded loose in tipper trucks or containers.
Chemical analysis of the material is available on request.
We are engaged in making Lead available in several forms including
LME registered and non registered 99.97% and 99.99% as well as
secondary ingots, foil, granules, powder, rod, shot, sheet, and wire.
Lead is a bluish-white lustrous metal. It is very soft, highly malleable, ductile, and a
relatively poor conductor of electricity. It is very resistant to corrosion but tarnishes
upon exposure to air. Alloys include pewter and solder.
We hold immense expertise in making available Copper in many forms
including LME registered and non registered cathodes, billets, rods,
cakes, bars, foil, sheet, granules, plates, powder, shot, turnings, wire,
insulated wire, mesh and “evaporation slugs”.
Copper is one of the most important metals. Copper is reddish with a bright metallic
lustre. It is malleable, ductile, and a good conductor of heat and electricity (second
only to silver in electrical conductivity). Its alloys, brass and bronze, are very important.
Monel and gun metals also contain copper. The most important compounds are the
oxide and the sulphate, (blue vitriol
Incoloy 825 is a nickel iron chromium alloy, which is widely used in petroleum, natural gas and chemical processing industries. It has good corrosion resistance and can operate at higher temperatures than most stainless steels. Incoloy 825 is a completely austenitic nickel iron chromium alloy, stabilized by titanium and added with copper and molybdenum. Incoloy 825 is a general engineering alloy, which is resistant to acid and alkali metal corrosion in oxidation and reduction environments.
The Incoloy825 has the following functions:
Good resistance to stress corrosion cracking.
Good resistance to pitting and crevice corrosion
Good oxidation resistance and non oxidative thermal acidity.
It has good mechanical properties at room temperature and high temperature up to 550
Certification of pressure vessels with manufacturing temperatures up to 450 C
Incoloy 825 metallographic structure:
Incoloy 825 alloy has a stable face centered cubic structure. Chemical composition and appropriate heat treatment ensure that the corrosion resistance will not be weakened by sensitization.
Incoloy825 Corrosion resistance:
Incoloy825 is a general engineering alloy, which is resistant to acid and alkali metal corrosion in oxidation and reduction environments.
Incoloy825 is widely used in various industrial fields where the working temperature is no more than 550.
Typical applications include:
Heating pipes, containers, baskets and chains for sulfuric acid pickling plants.
Seawater cooling heat exchanger, marine product pipeline system, acid gas environment pipeline.
Heat exchanger, evaporator, washing, immersion tube, etc. In phosphoric acid production.
Air heat exchanger in petroleum refining
Food Engineering
chemical process
Flame retardant alloy for high-pressure oxygen
Product name
INCOLOY Alloy 825
Grade
INCOLOY Alloy 825
Thickness range
0.3mm-3.0mm,
Width range
600mm-1500mm
Length
2000mm, 2438mm, 3048mm
Size
1000mm*2000mm, 1219mm*2438mm, 1219mm*3048mm, or as required
The third-generation Hastelloy alloy alloy20 is one of the more commonly used components in the C series. Due to its low nickel content, low cost, excellent mechanical and corrosion resistance, it is widely used in pump flow components where corrosion and wear coexist. The solubility of hardness in the ferrite phase reaches its maximum at 850, and as the temperature increases, the solubility increases rapidly and is much smaller than that of the austenite phase. The Cu content in c-276 has exceeded the high solubility in the ferrite phase.
The Hastelloy alloy alloy20, formed by a large amount of Ni element composition, is used in industries such as chemical engineering, pharmaceuticals, seawater, fertilizers, and other industries for projects with high corrosion resistance requirements due to its unique characteristics that lie between ferrite and austenite structures, and its resistance to intergranular corrosion. In recent years, the nuclear power industry has developed a corrosion-resistant ability in the operation of power station equipment, which cannot be replaced by other materials. Containing a large amount of Cr component, with high oxidation resistance.
The molybdenum element in stainless steel materials is only about 2%, which is far less than the molybdenum content of Hastelloy alloy alloy20. Therefore, high concentration acidity requires the use of materials well. Mainly used, it has the following corrosion resistance properties in oxidation and reduction, and excellent corrosion resistance to most corrosive media. In this oxidizing environment, such as in sulfuric acid manufacturing and solutions containing a large amount of oxidizing ions, it has excellent resistance to pitting corrosion, crevice corrosion, and stress corrosion.
Product name
ALLOY 20 STAINLESS STEEL
Thickness range
0.3mm-3.0mm,
Width range
600mm-1500mm
Length
2000mm, 2438mm, 3048mm
Size
1000mm*2000mm, 1219mm*2438mm, 1219mm*3048mm, or as required
Interior/exterior/architectural/bathroom decoration, elevator decoration, hotel decoration, kitchen equipment, ceiling, cabinet, kitchen sink, advertising nameplate
Warehouse Storage
Shandong Jintuo Metal Materials Co., Ltd is located in Liaocheng City, the capital of steel tubes. It is a large enterprise specializing in the sales of carbon steel, stainless steel, galvanized color coated products, and copper and aluminum.Our company adopts a flexible business approach and management mechanism to provide good services to customers, while also considering the interests of the owner and the project, in order to ensure the quality of the project.
Use of INCOLOY Alloy 825: 1. The heater is generally used in the oil refining unit; 2. Chemical plant equipment pipeline; 3. Fast cooling cylinder for solid solution used in textile industry; 4. Seamless steel pipe for heat exchanger and condenser. 5. High pressure seamless steel pipe for food (gb-2000) is a high-quality carbon structural steel and alloy steel seamless steel pipe suitable for chemical equipment and pipes with working temperature of - 40~400 �° C and working pressure of 10~30ma. 6. Seamless steel pipes for geological drilling and oil drilling control. 7. Cracking pipe for petrochemical industry is used to transport high-temperature and high-pressure fluid on fertilizer equipment.
INCOLOY Alloy 825
Standard
Food Grade Sanitary Tube: JIS G3447, KS D 3585, ASTM A270, EN 10357(DIN 11850), AS 1528.1, ISO 2037(NF A49-249)
Industrial pipe: ASTM A312, EN 10217-7, GB / T 12771-2008, HG 20537.3
Drinking water tube: GB / T 19228
Mechanical tube: ASTM A554, EN 10296-2
Size
Outer Diameter Range: 9.5~2000mm
Thickness Range: 0.5~20mm (Size can be customized.)
Length: Up to 11.8 meters per piece.
Shape Section
Round, square, rectangular
Usage
Sanitary tubing: for food processing industry, beverage industry, sugar mill and so on;
Heat exchanger tube: condenser, boiler, super heater, evaporator and so on;
Industiral pipe: for petroleum delivery, gas delivery, petrochemical industry, wastewater treatment, drainage system, and so on;
Mechanical tube: handrail, railings, balustrade, hence and so on.
Features:
1.Our stainless steel tubes pipes are treated by bright annealing, inside weld bead removing, precise polishing. The roughness of tubes could be under 0.3�¼m.
2.We have the non destructive testing ( NDT ), eg. online eddy current inspection and hydraulic or airtightness testing.
3. Thick welding, good appearance.The mechanical properties of tube could be tested.
4. And Our tubes are certificated by AD 2000-W0, PED 2014/68/EU, ISO 9001 : 2015.
5. Full material traceability is guaranteed during the manufacturing process.
6. Polished tube is supplied in individual plastic sleeves with capped ends ensuring optimum cleanliness.
7. Internal Bore: Tubes have a smooth, clean and crevice free bore.
We supply high-purity Zinc Alloy for industrial applications, ensuring exceptional quality and performance. Our material features a Zinc (Zn) content of 99.999%, with extremely low levels of impurities, making it suitable for critical uses across multiple industries.
Applications:
This high-purity zinc alloy is ideal for:
Electronics and semiconductors
Galvanization processes
Specialty coatings
Advanced alloy manufacturing
Research and development
With our stringent quality controls and reliable delivery network, we ensure that your specific requirements are met with excellence. Contact us for further information or to request a quote.
Sc(b)h15 amorphous alloy dry-type distribution transformer
Transformer can be installed indoors deep into the load center, so as to adapt to the need of high-density load of big modern cities. With the no-load loss reducing by 75% and the load loss reducing by 15% than that of gb/t10228 table 4 group i, the amorphous alloy distribution transformer is the state of the art energy efficient dry type transformer
Manufacturers, exporters & importers of stainless steel / copper / brass / aluminium / duplex steel / carbon steel / alloy steel in shape of pipes, tubes, flanges, pipe fittings,round bar, bright bars, angle bar, flat bar, hex bar, square bar, sheets, coils, strip, plates, wire, tie wire, strip banding, decorative tubes / pipe, valves, threaded fittings,forged fittings etc. in any shape / size / grade.
also specialised in high nickel alloys like inconel, monel, titanium, hastalloy etc. in any size / type / grade & as per drawing..Manufacturers, exporters & importers
