Hot Tack ASTM Plastic Membrane Heating Seal Hot Tack Testing Machine
Product Detail
Application:
The tester is used for the measurement of the strength of heat seals formed between thermoplastic surfaces of flexible barrier materials and webs, immediately after a seal has been made and before it cools to ambient temperature.
Hot Tack ASTM Plastic Membrane Heating Seal Hot Tack Testing Machine
Features:
1:Embedded system control, remote service and updating
2:Touch screen operation, easy to operate
3:TFT LCD display, UI flattening design
4:Dual heat jaws, temperature controlled independently
5:Hot tack curve and other graphic outputs.
6:Pressure easy to adjust, heat temperature and time touch screen input.
7:Sample pneumatic clamping
8: Over temperature protection, over pressure protection
9: RS232 communication port.
10: DSM system is optional(Laboratory Management Information System), easy to manage and share test data.
Hot Tack ASTM Plastic Membrane Heating Seal Hot Tack Testing Machine
Technical Indexes:
Sealing Temperature
Room Temperature~300C
Resolution
�±0.1C
Accuracy
±0.2
Sealing Pressure
0.1N/mm2~4.0N/mm
Dwell Time
0.025s~ 999.9s
Load Range
0~100N(Standard)
0~50N(Optional)
0~250N(Optional)
0~500N(Optional)
Humidity range
Max0.01% F
Heat Jaw Surface
10mm 40 mm (customized)
Peeling Speed
21mm/s-750mm/s
Sample size
Length 300mm, Width 40mm,
Thickness 1mm;
Hot eye Onion Peeling Machine
Automaitc onion peeling machine with onion root cutting in-one-machine
1 The whole process of onion from feeding, peeling, peeling, root cutting, output and other processes is automated and unmanned, which can save a lot of labor costs.
2 Peel by layers, either more or less. The equipment is designed with a cortex controller, which can be peeled as required. Only one layer of skin can be peeled, or two or three layers of skin can be removed.
3 The peeling is clean and effective. The peeled scallions are clean and good in appearance.
4 The root cutting part is equipped with an onion size recognition mechanism, and the size of the cutting amount can be adjusted randomly to avoid the disadvantage of cutting large onions into small ones and small ones into large ones.
5 Small size, high yield. The equipment design strives to reduce the volume on the premise of increasing the output, so as to apply to various application scenarios such as large, medium and small enterprises and small family workshops.
Dry-type onion peeling machine ,equpit the air compressor ,photo onion peeling machine capacity 50kg-2500kg/hour .
also have other different capacity onion peeling machine according to clients inquired.Onion diameter 30-120mm different model different capacity .
(also have garlic peeling machine for clients )
Hot selling tortilla making machine thin pancake making machine
Hot selling tortilla making machine ,1-row, 2-row ,3-row,4-row ,max 50mm diameter,we offer formula for clients,easy working,low cost high profit! tortilla with meat vegetable sauce together are very delicious for people eating !tortilla making machine also can produce Roti, Tortilla, Chapati, Pita
welcome order !
Factory Automatic Hot Eye Onion peeling process machine,from small capacity to big capacity
Onion peeling process: the onion is manually fed into the hopper --- the conveyor belt automatically feeds the onion into the peeling box for peeling --- after peeling, the onion goes into the peeling roller. Under the action of high-pressure air at the side, the first and second layers of the onion are peeled off and sent out to complete the whole processing process.
Features: 1. Advanced technology, reasonable mechanism, beautiful appearance, safe and reliable use, all stainless steel. 2. Automatic peeling without damage. 3. The depth of peeling is even. 4. The feeding belt is used for automatic feeding, which is simple in design and convenient in use. 5. Less peeling, high recovery rate of finished products, and over 98% of finished products. 6. Mechanical processing eliminates the hidden danger of manual processing of infectious diseases and unsanitary products.
Parameters
1.process arrange diameter of round shape onion 30-150mm.
2.capacity 1000-1500kg/h
3.Power 3kw
4.Voltage 380V
5.Air Compressor :flow 1.5m2/min, pressure 0.7MPa ,power 11kw
6.Machine size 1.5*1.3*1.4m
7.Weight 420kg
Start working flowing:
1.Fill onion in the loading box
2.Start the pneumatic valve switch
3.Start the power-supply switch
4.According to onion drying or fresh to adjust loading speed button/air pressure ,in order to ensure the clean degree of removing onion skin
5.When finished adjusting ,The equipment operates normally and automatically.
13189 Astm Hot Tack Testing Machine Suppliers
Short on time? Let Astm Hot Tack Testing Machine sellers contact you.
Product Name
Carbon steel plate 25crmo4 alloy steel sheet price
Thickness
3mm~300mm,2mm-100mm is common thickness,also can customize
Width
1000~3000mm,common width is 1250mm,1500mm,2000mm,2200mm
Length
1000~12000mm,can as your request cut
Surface
Clean,finished, blasting and painting or as your request
Delivery
Hot Rolled, Controlled Rolling,Normalizing,Annealing, Tempering,Quanching, Q+T
Packing
Steel Strapping,fixing in the Container,can customize
Product Name
Carbon steel plate 25crmo4 alloy steel sheet price
Thickness
3mm~300mm,2mm-100mm is common thickness,also can customize
Width
1000~3000mm,common width is 1250mm,1500mm,2000mm,2200mm
Length
1000~12000mm,can as your request cut
Surface
Clean,finished, blasting and painting or as your request
Delivery
Hot Rolled, Controlled Rolling,Normalizing,Annealing, Tempering,Quanching, Q+T
Packing
Steel Strapping,fixing in the Container,can customize
1.2m-12m or according to customer's special request
width
610,760,840,900,914,1000,1200,1250mm
Tolerance
Thickness: +/-0.02mm, Width:+/-2mm
Material grade
Q195 Q215 Q235 Q345
SS490 SM400 SM490 SPHC SPHD SPHE SPHF
SEA1002 SEA1006 SEA1008 SEA1010
S25C S35C S45C
65Mn
SPHT1 SPHT2 SPH3 SPH4
QstE
Others as your requirement
surface
iron gray (low carbon plate), brown (special alloy plate, the high carbon plate), partial ochre (weather resistance), with temperature oxidation pattern, than manufacture rough surface
The manufacture of both granulated and powdered garlic is the same, except for the grinding or powdering process. Granulated garlic is coarse while garlic powder is ground extra fine.
Whole cloves of garlic are peeled, cleaned and then sent into a machine that slices and chops them into smaller sections. The sections are dried in slow ovens for three to four hours. When the garlic has cooled it is ground to the desired consistency, be it granulated or powdered. The finished products are put through sifters to separate any debris or undesirable pieces. Both are packaged in air-tight containers and stored in a cool, dry place.
Granulated and powdered garlic are used to season and enhance the flavor of many foods. Often it is an appropriate substitute when fresh garlic is called for in a recipe. Powdered garlic dissolves almost instantly when incorporated into any dish, hot or cold. Granulated garlic takes a few minutes to become incorporated and release its flavor.
We can offer Garlic Granules in 0.5mm to 1.0mm, 40/60 mesh, 26/40 mesh
- 20 FCL: 10 Mt (Flakes/Cloves), 14-15 Mt (Minced/Granules/Powder)
- 40 FCL H/C: 20 Mt (Flakes/Cloves), 25-30 Mt (Minced/Granules/Powder)
Product Packing
- 12.5/13/14 Kg Paper Bag inside 1 Poly Bag
- 20/25 Kg Cartoon inside 1/2 Poly Bag
- 20/25 Kg Cartoon inside 1/2 Aluminium Foil Bag
Lump sulfur, also known as granular or rock sulfur, is typically characterized by a purity of 99.80% or higher, with a maximum ash content of 0.05%.
It should also have a limited acidity (H2SO4) of 0.02% or 0.03% and minimal moisture content (0.5% or 0.2%).
More detailed breakdown of lump sulfur specifications:
Purity:
Dry Basis: 99.80% minimum purity is a common specification.
Other Standards: Some standards like Refinery Specifications, may specify a purity of 99.98%.
Impurities:
Ash Content: A maximum ash content of 0.05% is a typical requirement.
Acidity: A maximum acidity (H2SO4) of 0.02% or 0.03% is common.
Organic Substances: Some specifications limit organic substances to 0.01% or 0.03% maximum.
Moisture: A maximum moisture content of 0.5% or 0.2% is generally specified.
Mechanical Impurities: Some specifications require the absence of mechanical impurities like paper, wood, or sand.
Other Impurities: Some standards specify limits for arsenic, selenium, tellurium, and lead impurities.
Color and Appearance:
Color: Bright yellow is the typical color specification.
Other Considerations:
Test Methods:
Specifications often include test methods, such as ASTM D-4239, ASTM D-1509, ASTM D-1613, and ASTM D-2790, for determining the various parameters.
Bulk Density:
Granular sulfur has a bulk density of around 70 lb/cu ft (1121.29 kg/cu m).
Solubility:
Sulfur is insoluble in water, partially soluble in acetone, and slightly soluble in diethyl ether and alcohol.
Steel billets result from the second stage of the steel production process. They are hot-rolled or forged from an ingot or strand cast.
steel billets from 45 x 45 mm to 150x150 mm, and round steel billets from 120 mm to 270 mm in diameter. Length : Specifiable up to 12 m Quality : In various internationally well known standards including afnor (nf), aisi, astm, bs, din, euronorm, gost, jis, iso, sae, si, ts, uni, etc. (eg. Astm a 615 gr 40 or 60, bst 420 s, din 488, st 37.2 din 17100, nfa 35015 and 16, bs 4449 (gr 250 or 460), jis g 3112 (sd 30, 35, 40), si 739 s 400, si 739 s 400 w, feb 44 k, 3 sp/ps or 5 sp/ps gost 380 88, 35 gs or 25 g2s, gost 5781-82, etc) Other grades available according to customer's request
Origin: Mexico
Code: 2025664BN
Material: PET bottle flakes
Hot washed Sortex Rejection / Blue and transparent
Category: PET
Type: bottle flakes
Color: Blue and transparent
Quantity: 400 Tons
Loading weight: 20 Tons
Specification: PET bottle flakes blue and transparent colors, hotwashed from Sortex Rejection
TDS same same as Test report
On going shpt
Thanks for contacting us!
We are selling CFR term, Incoterms 2020. Payment term: 50% advance, balance against copy Bill of Lading
Could you please give us more details about your company and demand for us to offer you the suitable material?
1.What is your company name and address?
2.Have you imported this material before?
3.If yes, which is your port of destination and HS code which you use to import this material?
4.How many tons do you need per month?
5.Which grade and color are you looking for?
6.Do you prefer us to contact you via email or whatsapp, wechat, skype,..?
Origin: Spain
Material: PET fines Clear blue
Category: PET
Type: fines
Color: Clear blue
Quantity: 40 Tons
Loading weight: 20 Tons
Specification:"PET Flake Specs as test report, hot washed
Loading weight: 20 MT per container.
Packed in 900kg of Big Bag big bags on pallets
40tons per month "
Thanks for contacting us!
We are selling CFR term, Incoterms 2020. Payment term: 50% advance, balance against copy Bill of Lading
Could you please give us more details about your company and demand for us to offer you the suitable material?
1.What is your company name and address?
2.Have you imported this material before?
3.If yes, which is your port of destination and HS code which you use to import this material?
4.How many tons do you need per month?
5.Which grade and color are you looking for?
6.Do you prefer us to contact you via email or whatsapp, wechat, skype,..?