Reactors are designed, manufactured and supplied in accordance
with GOST R 52630 : 2006, OST 26.291â??94 and/or EN 13445 4:2002, ASME Section VIII Div.1&2. Criteria for selection of materials for manufacturing of
reactor shells and piping are based on rich practical experience of AEM specialists in the sphere of oil refining, chemical and power units. Vessel designs may be complemented with other elements depending on input technical requirements and process parameters as defined at design stage
Technical specifications
Diameter: up to 5000 mm Nominal
pressure: up to 20 MPa
Wall thickness : up to 300 mm
Design fluid temperature: up to 550C
Material: single metal plated with corrosion resistant material, type
08�¥18�?10�¢, 0813, or other as required by technical design
Internals UOP, AXENS, RIFING, etc.
Service life : 30 years
electrical and lighting parts
electrical and lighting parts
electrical and lighting parts
electrical and lighting parts
electrical and lighting parts and accessories
electrical and lighting parts and supplies near me
electrical and lighting parts automotive
electrical and lighting parts appliance
electrical and lighting parts auto
electrical and lighting parts
electrical and lighting parts all
parts of a lighting fixture
parts of a light fixture diagram
electrical and lighting parts breaker
electrical and lighting parts before
electrical and lighting parts ba
electrical and lighting parts based
electrical and lighting parts breakdown
electrical and lighting parts by owner
electrical and lighting parts by vin
electric and light parts bulb
electric and light parts blue
electric and lighting parts board
b & p lamp parts
b and p lighting
b and l lighting
electrical and lighting parts cr
electrical and lighting parts certification
electrical and lighting parts crc
electrical and lighting parts crl
electrical and lighting parts catalog
3 phase mains and 3 phase generator voltage measurement,
3 phase load current and earth current measurement,
Contactor open and close relay outputs for mains and generator,
Configurable 6 inputs and 4 outputs,
3 resistive sender inputs for oil pressure, temperature and level,
Stop or fuel selenoid selection,
Programmable weekly working permit calendar,
Maintenance warning (working hour or elapsed month),
Exercise at programmed time intervals,
Off, manual, auto and test mode,
Power measurement by kva, kw, kvar, kvah, kwh, kvarh,
Compatible to diesel or gas generators
* sends sms to pre-defined gsm numbers for alarms
* controls the generator and monitors status information of the generator by sms
* remote control via internet, intranet, gsm or dial-up modem
* access to multiple generators by gen-agent scada software
* authorised access, secure communication
* suitable for telecommunication projects
* automatic transfer switching control and engine control
* logs last 32 events & alarm informations
* full metering facility, energy and power measurement
POWER SD 5 READY PLASTERING MACHINE
It is a high-performance ready-made gypsum plastering machine that pumps and sprays all kinds of gypsum or cement-based dry mixes and is used in interior and exterior plaster applications.
Technical Specifications
Machine Type: POWER SD 5
High quality mixing
Easily disassembled and transported
High quality electrical panel application
2 years warranty period â?? Delivery export value package type.
Technical Data
Power Supply 380 V - 50 Hz
Motor Power 5.5 kW
Compressor Capacity 250 liters/min - 5.5 bar
Carrying Capacity * 5-40 liters/min (These values may vary depending on the material used, the pumping height, the consistency of the pumped material, the type of pump, rotor and stator.)
Water pump 50 liters/min - 0.75kW
Transport Distance Horizontal * 40 meters (Standard if needed this will be long - option)
Transport Distance Vertical * 30 meters (Standard if needed this will be long - option)
Reservoir Volume 130 liters
Maximum Weight 285 kg
Maximum 100kg carrying capacity
Poliamid injection rollers with steel ball bearings
Galvanized/electrostatic painted sheet iron body
Roller module with height adjustment
Aluminium rail at top and bottom
Poliamid injection stopper at the upper rail
Uses with 16-18-20-22mm wooden panels as laid in.
Designed to meet slicing and packaging processes in the companies with high capacities.
*Breads placed on the band push each other and a continuous slicing is provided.
*Slicing is made in the desired speed through band speed adjustment.
*It is not proper for single slicing on the bench.
*Height can be adjusted in accordance with the bigness of bread.
*Machine is equipped with a packaging apparatus with fan to open the sachet as for packaging the sliced breads.
*Surface in touch with bread during slicing is made of 304 quality stainlesss stell and is sanitary for breads
*Sliced breads can easily be pushed by hand into the sachet that is opened by air. *After putting the breads in, the sachet is taken apart and the sachet down is again opened by air.
*Slice thickness can be adjusted from 8 mm up to desired value.
*It is produced with standard electrostatic kiln dyed and optional stainless body.
*It is easy to carry through the wheels.
*24 V Control Panel
*Has 2 years guarantee for production and assembly defects
TECHNICAL FEATURES
CAPACITY:1500/BREAD A HOUR
WIDTH:1180mm
LENGHT:1760mm
HEIGHT:1300mm
WEIGHT:298kg
POWER:1,59KW.
Slicing is made in the desired speed through band speed adjustment.
It is not proper for single slicing on the bench.
Height can be adjusted in accordance with the bigness of bread.
Machine is equipped with a packaging apparatus with fan to open the sacket as for packaging the sliced breads.
Sliced breads can easily be pushed by hand into the sacket that is opened by air.After putting the breads in, the sacket is taken apart and the sacket down is again opened by air.
Slice thickness can be adjusted from 8 mm up to desired value.
It is produced with standart electrostatic kiln dyed and optional stainless body.
It is easy to carry through the wheels.
Capacity:1500/hour
Gas spring (gas struts)
Gas springs are used everywhere that weights have to be pushed, lifted, lowered, pulled or set into position
Gas springs (gas struts, gas lifts) are applied on vehicles tailgates and bonnets, bus baggage lids and seats, caravan lids, tractor cabins, folding beds, office chairs, roof boxes and many other places according to costumer demands.
Costumers are able to choose from our oem or aftermarket products.They can also ask for their specifications. We offer different types of connection parts and brackets for our gas springs
Gas springs that are used on buses of mitsubishi, mercedes benz, man, daf, scania, b.M.C. Etc. Midibusses of iveco, isuzu, temsa, etc. And cars of renault, fiat, peugeot, lada, volvo, volkswagen, ford, opel, citroen, audi, bmw. Etc. Are among despa's sortiments
543 Electric Meter Testing Equipment Suppliers
Short on time? Let Electric Meter Testing Equipment sellers contact you.
