Hook Switch is applied to low current circuit hook switch for electronic equipment.
The standard test conditions shall be 5~35 in temperature, 45~85% RH and 860~1060 m bar.
Storage temperature range : 30 degree Celsius to 80 degree Celsius, however 96 hours maximum for continuous storage over a range
Tact Switch MT 1101 S is applied to low current circuit tactile switch for electronic equipment.The standard test conditions shall be 5 ~ 35 degree Celsius in temperature.
45 ~ 85% RH and 860 ~ 1060 m bar in atmospheric pressure.
Should any doubt arise in judgement, tests shall be conducted at 20±2 degree Celsius, 60±5% RH
Tact Switches MT 1102HT Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1kHz small-current contact resistance meter.
Insulation resistance Measurements shall be made following application of DC 100V Potential across terminals and frame for one minute
Tact Switches MT 1102 VS is applied to low current circuit tactile switch for electronic equipment .Contact resistance measured DC 5 V 1 A or by ohmeter allowing a small current at 1 kHz with a load of twice of the Actuating force
Insulation resistance DC 100V is applied between terminals and between terminals and cover for 1 minute ± 5 seconds
Tact Switches MT 1101 U is applied to low current circuit tactile switch for electronic equipment.
Contact resistance measured DC 5V 1A or by ohmeter allowing a small current at 1 kHz with
a load of twice of the Actuating force
Insulation resistance DC 100V is applied between terminals and between terminals and cover for 1 minute ± 5 seconds
380 Computer Software Hardware Suppliers
Short on time? Let Computer Software Hardware sellers contact you.
Dotech's complete solutions against refrigerant leak and noise
Accurate measurement with dedicated sensors (low and high pressure refrigerants)
Display of saturation temperature of refrigerant
All in one (pressure switch and gauge)
Easy installation
Dotech's complete solution against refrigerant leak and noise
Refrigerant-dedicated sensor for compressor or condenser fan
Smart control (step control, rotating operation, delay time Set, pressure control modes)
Digital All-in-one (pressure switches, gauge and controller)
Easy installation and reasonable price
Featuring our high-end analyzer, Hercules, and compact S4 wireless hardware, this package is designed to support advanced communication with in-vehicle networks for use in a variety of OEM and supplier applications including diagnostics, simulation, and various custom applications. See the Datasheet for more information.
Hercules supports CAN, Class2, and LIN protocols along with full support for GMLAN diagnostics. It also includes graphical display, real-time data playback, and hot-key service sending, among many other features.
*For a complete list of all of the Hercules features, please refer to its technical data sheet, and the Gryphon / S-CAT Modules data sheet.
The Gryphon S4 hardware is compact, fast, and has built-in support for CAN, along with one expansion slot to support a specific plug-in protocol module. Read about Gryphon Modularity.
Additionally, it includes a 10/100T Ethernet connection.
Introduction to using the G2 as a vehicle network communication device to design and development a vehicle network
How to use the Tx and Rx functions to send and receive messages on the data bus
Common Applications
Application Description
Monitoring
Analysis
Diagnosis GRYPHON S4 is also used as an interface for our Hercules CAN Analyzer software tool. Hercules is our high performance Windows analyzer software with protocol support for CAN (canbus), GMLAN, ISO11898 (CAN), ISO15765, J1850 GM (Class 2), J1939, J1979, J2284, J2411 (GM SW), LIN and SWCAN.
PV / DV Interface
Analysis
Diagnosis Included in test stand applications.
Available Accessories and Options
The following items are available.
Part Number Product Name
DG-S4-MX16-CABLE An Open Ended cable to the S4's MOLEX connector.
WLI-UC-GNM Wireless nano USB adapter.
DG-UNVPWR Universal power adapter 100-240VAC/12VDC.
DG-OBDII-BOX In-line breakout box to J1962 connectors.
As a near-by card reader, it reads the inherent information from an entry card, and sends the data to entry control system.
Function
- ISO 14443A/Mifare type Card is supported.
It functions as a recognition device by connecting to entry control system controller.
Tamper Alarm Function
- Alarm of the detachment and opening of a card reader (Alarm Sound is emitted.)
- It is possible to send alarm data in using RS-485 communication way.
Voice Guidance Service Function (Option)
Specification
- Communication with a Controller
RS-485/Wiegand Output
Metal Cabinet
- Tamper Alarm HOST
RS-485 1PORT, 9600/19200/38400 bps
AUX. : RS-485 1PORT, 9600/19200/38400 bps
380 Computer Software Hardware Suppliers
Short on time? Let Computer Software Hardware sellers contact you.
