LED fluorescent tube glass 120 cm (www.Beneled.nl)
Replace the old-fashioned fluorescent tube 120 cm 1 on 1 with our LED fluorescent tube glass. The fitting of the LED fluorescent tube is identical to the old-fashioned fluorescent tube, so it always fits into an existing fixture with a T8 / G13 fitting.
Pay attention! These LED fluorescent tubes work in 3 ways.
1. In an existing fixture with starter. Replace the conventional starter with an LED starter and you can use these LED fluorescent tubes. This LED starter can optionally be checked with the LED fluorescent tube.
2. In an existing fixture without a starter. You must adjust the wiring. The phase and neutral wire must be connected directly to 1 end of the luminaire / LED fluorescent tube. Ballast and starter are not required.
3. Connect our LED fluorescent tube directly to 230V at 1 end of the LED tube. On the LED tube the L and N are indicated on 1 side. You can connect the power directly to this side. Ballast and starter are not required.
An extra energy saving can be achieved if the LED tube light is connected directly to the power. The phase and zero 230V must then be connected to 1 end of the LED fluorescent tube.
Hours of life: LED tubes last more than 50,000 hours, compared to 10,000 from a good fluorescent tube
Resistance: LED tubes are much more resistant to shocks or vibrations than fluorescent tubes. In fact, they are removable and repairable, something that is unthinkable for fluorescent tubes.
Consumption: LED tubes consume considerably less than fluorescent tubes. A 600 mm-18 W fluorescent tube with reactance and starter can consume twice its nominal power due to the reactance. We are talking about a 36 W consumption compared to the 8 or 12 W consumption of the 600 mm LED tube.
Started: the LED tubes can be started immediately and have no influence on their lifespan. When changing a fluorescent tube it is necessary to start and the number of daily inflammations influences the lifespan. For example, many fluorescent tube manufacturers estimate the lifetime of the tube in 10,000 hours, taking into account only 2 inflammations per day.
Environment: LED tubes do not need gas to ignite, fluorescent lamps are manufactured with mercury vapor and mercury compounds are extremely dangerous chemicals for human health and the environment.
How fast can I debit the switch from conventional tubes to LED tubes?
This data depends on various factors: number of hours on, days, and hourly discrimination rate. We can provide sufficient objective advice so that you can have reimbursement conditions depending on the characteristics.
Steps to take before investing in LED tubes
Before you buy LED tubes, you must take into account the previous advice, value for money, to be able to purchase a LED tube with warranty. Also keep in mind that you have all CE and RoHS certifications.
Copper Wire Application: Air Condition or Refrigerator, Water Tube, Water Heater, Oil Cooler Pipe Material: COPPER Shape: Coil Alloy: Non-alloy Color: Golden
TASTE-4-ALL SPICY UMAMI FLAVOR
(Known under the popular name: SPICY UMAMI)
SPICY UMAMI is a natural powder flavor made from various herbs and spices combined with natural yeast extract. Clean label, so no E numbers, no artificial color, no preservatives, no anti-caking, no artificial anything! Halal and Kosher certified.
A real Taste-4-All product, applicable in numerous food products. Examples: Sausages, Soups, Pastas, Nuggets, Chicken (Wings), Dressings, Seasonings, Canned Meat/Fish, Vegan Products, Canned Vegetables, Savory bakery products,
Chips, Meat products etc.
Simple to experience the taste: dissolve a teaspoon of SPICY
UMAMI in a glass of hot water and taste.
Use: SPICY UMAMI can be used in a very low dosage as
taste supporter, like in canned vegetables. Or as a main taste
giver in a much higher dosage in for instance sausages.
Dosage: experimental depending on taste.
Note: Keep packaging closed when not in use.
Kelo-Cote is a patented silicone gel for the prevention and treatment of hypertrophic scars and keloids resulting from surgery, trauma, wounds or burns.
Kelo-Cote is a silicone gel that:
- Reduces the redness of scars.
- Makes raised scars smoother and flatter.
- Relieves the itching and pain of scars.
Indications :
For the prevention and treatment of hypertrophic scars and keloids resulting from surgery, trauma, wounds or burns
Directions for use :
For recent scars: apply to a clean, dry scar once healing is complete or sutures have been removed.
Apply a very thin layer of Kelo-Cote to the scar, twice a day, without massaging.
Allow to dry for 5 minutes to form a soft, transparent, water resistant film - remove excess if film does not dry. Once dry, it can be covered with sunscreen or makeup.
The recommended treatment period is 2-3 months. Continue treatment if improvements are still seen.
Ceramic UPC (Used Product Components) scrap refers to discarded ceramic materials from various applications, including electronics, automotive parts, and household items. This scrap can be recycled and repurposed for various uses, including in the manufacturing of new ceramic products, construction materials, and as fillers in composites.
Product Overview:
Ceramic UPC scrap includes a variety of ceramic materials that are no longer in use. Common sources include broken tiles, porcelain, and other ceramic components found in consumer products and industrial applications.
Features:
Durability: Ceramics are known for their hardness and resistance to wear, making them valuable even in scrap form.
Recyclability: Ceramic UPC scrap can be processed and recycled, contributing to sustainability in manufacturing and reducing landfill waste.
Applications:
New Ceramic Products: Recycled ceramic scrap can be reprocessed into new tiles, pottery, and industrial ceramics.
Construction Materials: It can be used as aggregate in concrete or as a filler material in construction applications.
Composites: The scrap can be incorporated into composite materials to enhance strength and durability.
Environmental Impact:
Recycling ceramic UPC scrap reduces the demand for raw materials and minimizes environmental impact by diverting waste from landfills. This process also lowers energy consumption associated with producing new ceramics.
We load approx. 28 Mt in 40' FT container. Our shreded tires are mixed with cars.
Shreded Tires are loaded in bulk . When container open then they can easily be loaded on the truck.
1 BALE= APPROXIMATE 1 MT PLUS MINUS.
1 BALE CONTAINS AROUND 100 TIRES BALED PRESSED TOGETHER COMING FROM CARS, SUVS AND SMALL TRUCKS.
NO OTR TIRES.
PACKING: 26 Tons on a 40, total 26 MT per 40
LED and free maintenance explosion-proof
project/spotlight lamp
80~150W, Lens
Protection grade: IP66
Anti corrosion grade: WF2
Ex-proof grade: Ex d IIC T6 Gb
We load approx. 28 Mt in 40' FT container. Our shreded tires are mixed with cars.
Shreded Tires are loaded in bulk . When container open then they can easily be loaded on the truck.
1 BALE= APPROXIMATE 1 MT PLUS MINUS.
1 BALE CONTAINS AROUND 100 TIRES BALED PRESSED TOGETHER COMING FROM CARS, SUVS AND SMALL TRUCKS.
NO OTR TIRES.
PACKING: 26 Tons on a 40, total 26 MT per 40
