Find Verified Silicon Dioxide Suppliers, Manufacturers and Wholesalers

Salient Features
Highly efficient 3-phase water filled motor
- Easily rewindable
- Dynamically balanced design
- Extended life with flawless performance
- Thrust bearing : Carbon + S.S. material for High thrust load capacity
- 100% EC grade copper winding
- Presenting world 1st design (design registered 100% fully S.S.-304 investment casting pumps.
- Zero maintenance
- Superior performance
- Sand proof operation
- Highly efficient 3-phase water filled motor

Product Specification
Power Range : 1.0 HP to 20.0 HP
Operating Speed : 0 - 2890 RPM
Operating Frequency : 0 - 50 Hz
Input Solar DC Power Range : 900 Wp, 20000 Wp
Input Solar DC Voltage Range : 110 Vmp - 600 Vmp
Head Range : 30 Mtr , 220 Mtr
Discharge Range : 10000 LPD - 420000 LPD
Type of Duty : S1

material of construction - motor
Part Grade
Body Lock : Spring Steel
Stud Ring : M.S. (Zinc Coated)
Stator Stamping : CRNGO - M45 Silicon
Winding Wire : 100% EC Copper
Shaft : SS-420
Rotor Stamping : CRNGO - M45 Silicon
Copper Lamination : 100% EC Copper
Upper Housing : SS-304
Lower Housing : SS-304
Connection Piece : SS-304
Oil Seal : NBR
TB Set : Carbon + SS
Base : SS-304
Drain Plug : Brass
Couple Sleeve : Stainless Steel
Water Bolt : Brass

MATERIAL OF CONSTRUCTION PUMP
Part Grade
Suction : SS-304
Couple : Stainless Steel
Couple Counter : SS-304
Rubber Seal : NBR
Bush Seal Cover : SS-304
Bowl : SS-304
Impeller : SS-304
Key : SS-410
Bowl Bush : NBR
Bush : LTB-4
Middle : SS-304
Cap : NBR
Outlet : SS-304

V9-V10 Borewell Submersible Pumpset

Falcon Dlx. 250 mm ( 9 & 10) Borewell Submersible Pumpsets are powered by water filled, rewindable submersibleMotor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under
pressureand rigidly locked in stainless steel stator shell. T-Bolt design in all motor ensures rigid construction.

Pump Liquids
- Clean
- Thin
- Non-Aggressive
- Non-Explosive
- Clear
- Cold
- Fresh water
- Without abrasives
- Solid particles

Salient Features
- SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow MRS series 27Mtr head per stage in radial flow series.
- FG 250 Cast Iron Bowl with CED Catted and SS-304 Grade Impeller in Mix flow FMC Series 22Mtr head per stage in
Mix flow series.
- Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads.
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set.
- Dynamically balanced rotating parts ensures minimum vibration and longer life.
- Designed for wide voltage fluctuations.
- Motor portion covered with corrosive resistance Stainless steel (SS 304) shell.
- More durability and hygiene & High operating efficiency.
- Specially designed thrust bearing to withstand high axial thrust load.
- Extremely hardwearing water lubricated bearing.
- Thread type motor construction ensures service feasibility.
- Designed for wide voltage operation.
- Best alternative for JET & Compressor pump set.
- Additional intermediate bearing in higher stage pumps.

Specification
- Power Range : 55 kW to 112 kW (75 HP to 150HP)
- Version : Three Phase 350 to 415V, 50Hz AC Supply
- Speed : 2900 RPM
- Head Range : 12 mtr. To 300 mtr.
- Discharge Range : 3600 LPM to 960 LPM
- Outlet Size in Inch : 4.0" & 5.0"
- Degree of Protection : IP 58
- Maximum Starts Per Hour : 10 Times

Falcon Premium 200 mm (8) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under
pressure and rigidly locked in stainless steel stator shell.

Pump Liquids
- Clean
- Thin
- Non-Aggressive
- Non-Explosive
- Clear
- Cold
- Fresh water
- Without abrasives
- Solid particles.

Salient Features
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set
- SS-304 Grade investment casting bowl and SS-304 grade impeller in radial flow series
- 20 Mtr. Head per stage in radial flow series
- Specially designed high performance thrust bearing (SS-420 Tilting pad with carbon plate) to with stand axial thrust
loads
- Dynamically balanced rotating parts ensures minimum vibration and longer life
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Special designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures services feasibility
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps
- Fully SS Pumps are available

Specification
Direction of Rotation : Counter clockwise from driving end -1ph : Electrically Reversible -3ph
- Power Range : 7.5 kW to 75 kW (10 HP to 100 HP)
- Version : Three Phase 350 to 415V, 50Hz AC Supply
- Thrust Load : 7.5 kW -30 kW -10000 lbs
- Speed : 2880 RPM
- Head Range : 12 Mtr. To 440 Mtr.
- Discharge Range : 2400 LPM to 300 LPM
- Outlet Size in Inch : 4.0" & 5.0"
- Degree of Protection : IP 58
- Minimum Cooling Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : Star Delta (SD)
- Maximum Starts Per Hour : 20 Times

Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5

V7 Borewell Submersible Pumpset

Falcon Premium 175 mm (7) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under
pressure and rigidly locked in stainless steel stator shell.

Pump Liquids
- Clean
- Thin
- Non-Aggressive
- Non-Explosive
- Clear
- Cold
- Fresh water
- Without abrasives
- Solid particles.

Salient Features
- Cast iron casting bowl and SS-410 grade impeller in mix flow series
- Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial
thrust loads.
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set
- Dynamically balanced rotating parts ensures minimum vibration and longer life
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Special designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures services feasibility
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps

Specification
- Method of Starting : 3 ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 37.3 kW
- Power Range : 11.2 kW to 37.3 kW (15 HP to 50 HP)
- Version : Three Phase 350 to 415V, 50Hz AC Supply
- Speed : 2880 RPM
- Head Range : 18 Mtr. To 650 Mtr.
- Discharge Range : 1860 LPM to 55 LPM
- Outlet Size in Inch : 2.0 , 2.5 , 3.0 & 4.0
- Degree of Protection : IP 58
- Direction of Rotation : Electrically Reversible -3ph
- Thrust Load : 11.2 kW -37.3 kW -8000 lbs
- Minimum Cooling Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Maximum Starts Per Hour : 20 Times

Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5

V6 Borewell Submersible Pumpset
Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure.

Pump Liquids
- Clean
- Thin
- Non-Aggressive
- Non-Explosive
- Clear
- Cold
- Fresh water
- Without abrasives
- Solid particles.

Salient Features
- SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series
- 60 feet head per stage in radial flow series
- Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial
thrust loads.
- Dynamically balanced rotating parts ensures minimum vibration and longer life
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Extremely hardwearing water lubricated bearing
- Specially designed Deep Drawn type pump ensures perfect
alignment and Thereby increases the life of the pumpset
- Designed for wide voltage operation
- Additional intermediate bearing in higher stage pumps
- Fully SS pump set are available in SS - 304 Grade

Specification
- Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP)
- Version : Single Phase 180V to 230V, Three Phase 350 to 415V,
50Hz AC Supply.
- Speed : 2900 RPM
- Head Range : 12 Mtr. To 600 Mtr.
- Discharge Range : 1080 LPM to 170 LPM
- Outlet Size in Inch : 2.0, 2.5 , & 3.0
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph
- Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct
Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW
- Maximum Starts Per Hour : 20 Times

Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.)
6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5

Monoblock pumps -
Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the
frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise
thereby increasing the life cycle of the motor.

salient features
- High operating efficiency resulting in lower power consumption
- Good suction lift characteristics
- Inbuilt thermal overload protector in al single phase pumpsets upto 2.0 HP
- Specially designed for wide voltage operation
- Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life
- Back pull-out design for easy servicing and repair
- Double shielded ball bearings, so no need of external lubrication
- All Model fitted to Mechanical seal.

specification
- Power Range : 0.37Kw - 1.5 Kw (0.5 HP - 2.0 HP)
- Version : Single Phase, 220-240V, 50Hz AC Supply
Three Phase, 380-415V, 50Hz AC Supply
- Speed : 2880 RPM
- Maximum Total Head : 32 Mtr.
- Maximum Flow Rate : 940 LPM
- Maximum Suction Lift : 7 Mtr.
- Degree of Protection : IP 44
- Class of Insulation : B0
- Maximum Ambient Tem. : 40 C
- Sealing : Mechanical Seal
- Type of Duty : S1 (Continuous)
- Method of Starting : Permanent Split Capacitor (PSC)
- Direction of Rotation : Three Phase, Electrically Reversible
- Nominal Pumpset Size (Suction X Delivery in inch) : 25 X 25, 32 X 25, 40 X 32, 40 X 40, 50 X 40,
50 X 50, 65 X 50, 80 X 65, 80 X 80 (All size in mm)

characteristics of clear cold water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5
Part Name Material
Mechanical Seal : Carbon & Ceramic
Motor Shaft : EN-8
Motor Body : FG-250
Bearing : SKF
End Cover : FG-250
Bracket : FG-250
Flange : FG-250
Casing : FG-250
Impeller : FG-250
Cooling Fan : Plastic

Monoblock Pumps
Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the
frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise
thereby increasing the life cycle of the motor.

salient features
High operating efficiency resulting in lower power consumption
- Good suction lift characteristics
- Specially designed for wide voltage operation.
- Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life.
- Back pull-out design for easy servicing and repair.
- Double shielded ball bearings, so no need of external lubrication.
- Mechanical seal is provided as per customers requirement

Specification
- Power Range : 2.2 Kw - 11.2 Kw (3.0 HP - 15.0 HP)
- Version : Three Phase, 380-415V, 50Hz AC Supply
- Speed : 2880 RPM
- Maximum Total Head : 65 Mtr.
- Maximum Flow Rate : 1450 LPM
- Maximum Suction Lift : 7 Mtr.
- Degree of Protection : IP 44
- Class of Insulation : B0
- Maximum Ambient Tem. : 40 C
- Sealing : Stuffing Box
- Type of Duty : S1 (Continuous)
- Direction of Rotation : Three Phase, Electrically Reversible
- Nominal Pumpset Size (Suction X Delivery in inch) : 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80
100 X 80 and 100 X 100 (All size in mm)

Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 1.75 x 10 mÃ?/sec (max.)
- Ph Value : 6.5 to 8.5

Material of construction - motor
Part Name Material
Gland Dori : Graphite String
Motor Shaft : EN-19 with SS SLEEVE
Motor Body : FG-250
Bearing : SKF
End Cover : FG-250
Bracket : FG-250
Flange : FG-250
Casing : FG-250
Impeller : FG-250
Cooling Fan : Aluminium

Falcon regenerative monoset pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the
frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise
thereby increasing the life cycle of the motor.

Salient Features
High operating efficiency resulting in lower power consumption.
- Good suction lift characteristics.
- Specially designed for wide voltage operation.
- Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life.
- Back pull-out design for easy servicing and repair.
- Double shielded ball bearings, so no need of external lubrication.
- All Model fitted to Mechanical seal.

specification
Power Range : 0.37 Kw - 0.75 Kw (0.5 HP - 1.0 HP)
- Version : Single Phase, 220-240V, 50Hz AC Supply
- Speed : 1440 RPM
- Maximum Total Head : 18 Mtr.
- Maximum Flow Rate : 4200 LPH
- Maximum Suction Lift : 8 Mtr.
- Degree of Protection : IP 44
- Class of Insulation : B0
- Maximum Ambient Tem. : 40 C
- Sealing : Mechanical Seal
- Type of Duty : S1 (Continuous)
- Direction of Rotation : Single Phase, Clockwise from driving end
- Nominal Pumpset Size (Suction X Delivery) : 25mm X 25mm

Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5

material Of construction - Motor
Part Name Material
Mechanical Seal : Carbon & Ceramic
Motor Shaft : SS-410
Motor Body : FG-250
Bearing : SKF
End Cover : FG-250
Bracket : FG-250
Flange : FG-250
Casing : FG-250
Impeller : Brass
Cooling Fan : Plastic

Monoblock pumps
Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the
frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise
thereby increasing the life cycle of the motor.

Salient Features
High operating efficiency resulting in lower power consumption.
- Good suction lift characteristics.
- Specially designed for wide voltage operation.
- Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life.
- Back pull-out design for easy servicing and repair.
- Double shielded ball bearings, so no need of external lubrication.

specification
- Power Range : 1.5 Kw - 5.5 Kw (2.0 HP - 7.5 HP)
- Version : Three Phase, 380-415V, 50Hz AC Supply
- Speed : 1440 RPM
- Maximum Total Head : 12 Mtr.
- Maximum Flow Rate : 3160 LPM
- Maximum Suction Lift : 7 Mtr.
- Degree of Protection : IP 44
- Class of Insulation : B0
- Maximum Ambient Tem. : 40 C
- Sealing : Stuffing Box
- Type of Duty : S1 (Continuous)
- Direction of Rotation : Three Phase - Electrically Reversible
- Nominal Pumpset Size (Suction X Delivery in inch) : 80 X 80, 100 X 100, 125 X 125, 150 X 150
(All size in mm)

Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5
Part Name Material
Gland Dori : Graphite String
Motor Shaft : EN-19 with SS SLEEVE
Motor Body : FG-250
Bearing : SKF
End Cover : FG-250
Bracket : FG-250
Flange : FG-250
Casing : FG-250
Impeller : FG-250
Cooling Fan : Aluminum

Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under
pressure.

Pump Liquids
- Clean
- Thin
- Non-Aggressive
- Non-Explosive
- Clear
- Cold
- Fresh water
- Without abrasives
- Solid particles

Salient Features
- SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series
- 60 feet head per stage in radial flow series
- Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads.
- Dynamically balanced rotating parts ensures minimum vibration and longer life
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Extremely hardwearing water lubricated bearing
- Specially designed Deep Drawn type pump ensures perfect
alignment and Thereby increases the life of the pumpset
- Designed for wide voltage operation
- Additional intermediate bearing in higher stage pumps
- Fully SS pump set are available in SS - 304 Grade

Specification
- Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP)
- Version : Single Phase 180V to 230V, Three Phase 350 to 415V,
50Hz AC Supply.
- Speed : 2900 RPM
- Head Range : 12 Mtr. To 600 Mtr.
- Discharge Range : 1080 LPM to 170 LPM
- Outlet Size in Inch : 2.0, 2.5 , & 3.0
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph
- Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct
Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW
- Maximum Starts Per Hour : 20 Times

Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5

V5 Borewell Submersible Pumpset
Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are
assembled under pressure and rigidly locked in stainless steel stators shell.

Pump Liquids
- Clean
- Thin
- Non-Aggressive
- Non-Explosive
- Clear
- Cold
- Fresh water
- Without abrasives
- Solid particles.

Salient Features
- SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series)
- 9 Mtr. Head Per Stage In Radial Flow Series.
- Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads.
- Dynamically balanced roating parts ensure minimum vibration and longer life
- Motor Portion covered with corrosion resistant S.S. J4 shell
- More durability and hygiene
- High operating efficiency
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect
alignment and Thereby increases the life of the pumpset
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps
- Fully SS pumps are available in (GRS - Series)

Specification
- Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP)
- Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply
(Single Phase available in 3 HP to 5 HP)
- Speed : 2880 RPM
- Head Range : 12 Mtr. To 640 Mtr.
- Discharge Range : 690 LPM to 80 LPM
- Outlet Size in Inch : 1.5 , 2.0" & 2.5"
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph
- Thrust Load : 2.2 kW, 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2
kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star
Delta (SD) upto 9.3 kW
- Maximum Starts Per Hour : 20 Times

Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5

Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell

Pump Liquids
- Clean
- Thin
- Non-Aggressive
- Non-Explosive
- Clear
- Cold
- Fresh water
- Without abrasives
- Solid particles.

Salient Features
- SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series)
- 9 Mtr. Head Per Stage In Radial Flow Series.
- Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial
thrust loads.
- Dynamically balanced roating parts ensure minimum vibration and longer life
- Motor Portion covered with corrosion resistant S.S. J4 shell
- More durability and hygiene
- High operating efficiency
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect
alignment and Thereby increases the life of the pumpset
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps
- Fully SS pumps are available in (GRS - Series)

Specification -
- Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP)
- Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply
(Single Phase available in 3 HP to 5 HP)
- Speed : 2880 RPM
- Head Range : 12 Mtr. To 640 Mtr.
- Discharge Range : 690 LPM to 80 LPM
- Outlet Size in Inch : 1.5, 2.0" & 2.5"
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph
- Thrust Load : 2.2 kW â?? 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2
kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star
Delta (SD) upto 9.3 kW
- Maximum Starts Per Hour : 20 Times

Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m²/sec (max.)
- Ph Value : 6.5 to 8.5

Silicon Foot Insole

Code- OC 3032