Find Verified Used Batteries Suppliers, Manufacturers and Wholesalers

The equipment is designed and manufactured by Gough & Co Ldt, UK in year 1999 / installed in 2000, manufacturer’s type single deck Vibracon GVF4. We have totally 3 identical units which were dismantled in 2007 and all of them are in very good operational condition. These are single deck circular screen design for high velocity scalping, de-watering or single deck separation in chemical and pharmaceutical industry. (These units were screening oversized particles in PVC - granulate factory truck loading station) The perforated screen and all product touching parts are made on stainless steel AISI 304L. Top deck houses the screen and the discharge spout for oversize particle removal is fitted to it. Top deck is supported with mechanical spring and vibration movement is created by two contra rotating vibrating motors on the outside of the unit so there are no internal working parts. Vibration power can be adjusted.

Technical data:
Type: Vibracon GVF 4
Material: AISI 304L – product touching parts
Perforated screen: Mesh size 4 mm
Screen diameter: 1100 mm
Screen area: 9500 cm2
Vibrators: 2 x 0.52 kW units.

The vacuum evaporator is made by Italian Ecoteck in year 2003 and operation was stopped in early 2009 and it is in very good operational condition. This unit is made for concentrate acidic liquid wastes and therefore all liquid touching parts are made of acid proof steel ( SS 2353) or PVC. The evaporation capacity of the unit is 5000 liters / day. The unit is a complete working unit and it includes evaporator, boiler, heat pump, centrifugal pump, water-air cooler, steam ejector, control unit and all other necessary equipment to complete the unit.

Operation principle:
Steam rises from the boiler through a drop dispenser to the cooling unit where it condensates. The condensate drops with the gravity down to vacuum system. In-build heat pump heats up the cooling media and simultaneously cools down the condensate. Water – air cooler cools down the extra heat from the process. Necessary vacuum is generated with a centrifugal pump and a steam ejector. Condensate rejection takes place in accordance with prescheduled frequency.

Technical data:
Manufacturer: ECOTECH Srl Italy / Vilokan Ren Miljöteknik Sweden
Type: ECO 5000 VS-HP, R407C
Year made: 2003
Evaporation capacity: 5000 liters / 24 hour (pure water)
Electricity consump.: about 0,15 kWh / liter pure wateri)
Control unit: Siemens Micromaster 420
Compressor: Bitzer Kuhlmachinenbau GmbH,
Compressor type: 6G-40,2
Compressor capacity: 126.8 m3/h, 19/28 bar
Refrigenerant: R 407 C
Main dimensions: 2.8 m x 1.3 m x 2.9 m
Weight: 1500 kg.

Tungsten W catalyst. Based on Assay
- with 14-15% W and 3,5-4,5% Ni
- in barrels about 18-20 tons
- fine granules, about 2cm in length
- notification can be done if needed.
- Origin EU, loading port EU Port

Modem

External basic ADSL modem for single computers. Connection to PC is USB. ull rate speed support up to 8MBps
The modems are ANNEX A type and there is support for
major protocols: G.DMT, T1.413, PPPoA, PPPoE, T1.483
Issue 2
G.992.1, G992.2.

9x/Me/NT/2000/XP.
Qty: 7000 pcs in-stock
Brand new, bulk packed (20 in box)
Warranty 1 year
Price $7 each , or make offer to take all
FOB Helsinki , Finland


Bulk, 20 pcs in a box

Good condition GEA Westfalia centrifugal separator used for molasses removal from fermented beer. The equipment has patented HydroStop solid discharged system that can be adjusted precisely and reproducibly to the specific solids concentration requirements of the process. This beer separator has continuous and self cleaning separation process and in beer filtration application this separator eliminates the need to use kieselghur.

Technical information:

Manufacturer: - GEA Westfalia Germany
Year of manufacturing: - 2002
Manufacturer's type: - SC 30-06-177
Capacity: - 4000 - 6000 liters / hour
Electric drive: - 18.5 kW
Bowl diameter: - 440 mm
Bowl speed: - 7270 rpm
Relative density of solids removed: min 1.4 kg/l
Relative density of suspension: max 1.2 kg/l
Particle size or removed solids: > 4.6 micron
Centrifugable solids: - max 5% v/v
Viscosity of free liquid: - 2.5 - 5.5

e equipment was manufactured by Jeffrey Rader AB, Sweden in 1995 and it is in very good operational condition. It consist of two heavy duty rolls with removable profilied surfaces which rotate towards each other and presses overzised wood chips between the profiles. Roll drives 2 x 110 kW / 1500 rpm connected with two gearboxes. Hydraulic pump 7.5 kW, capacity 220 m3/h wood chips.

The equipment was manufactured by Jeffrey Rader Inc, Sweden in year 1995, manufacturers type is DynaYield 80-300 and it is in good operational condition. The Chip Conditioner consists of two heavy duty rolls with removable profiled surfaces. They rotate towards each other and pull the oversize chips between them. The profiled surfaces are aligned so that the pyramid apexes on one roll travel in the valleys of the apexes on the adjacent roll. With normal oversize wood, the Conditioner typically generates less than 1% fines and 3% pins
The normal application for the Chip Conditioner is in a chemical pulping process, processing the oversize materials by fissuring the wood chips parallel with the grain to allow the cooking liquors to penetrate the chip, and allow the oversize chip to cook as an acceptable size chip. Another application is in a thermo-mechanical pulping process (TMP), as a preconditioning
An important feature of this machine is its ability to handle small portions of tramp without going off-line. With the so called Dynagage Conditioner, the dynamic roll is allowed to move away from the static roll, and once the tramp is through the unit, the roll automatically moves back to the proper set point without shutting down the flow and together with slow rotation speed enable were low down time and maintenance costs. Roll distance movements are made with a hydraulic system build on the equipment and controlled by 3 position sensors
More information on requests, for spam protection please introduce yourself properly.

Technical data:
Model: RDY 80-300
Manufacturing year: 1995
Capacity (throughput): 220 m3/h loose wood chips
Press roll diameter: 915 mm
Roll length: 2440 mm
Roll motors: 2 x 110 kW / 1500 rpm / 690 V – 50Hz
Press distance between the rolls: 2.2 mm
Gearboxes: 2 x Kipo Benzler TV 512
Hydraulic pump: Rexroth 200 bar with Mecman syliders
Electric motor for hydraulic pump: ASEA 7.5 kW
Weight: 33 000 kg
Length: 5083 mm
Width: 2550 mm
Height: 2400 mm.

Krones Toptronic K 719-555 Rotary Empty Bottle Inspector

The Toptronic inspector is made for inspecting empty returnable PET bottles and empty non-returnable and returnable glass bottles. It utilizes state-of-the-art camera technology to provide precision empty container inspection. The sophisticated inspection modules detect even the tiniest damage or contamination – both in glass and PET returnable bottles.

General design features
Modular design
Table top cover and stand cladding in stainless steel
Safe bottle guidance with Raptec handling parts
Blower for removing foam and lubricant residues from the container base
Enclosed and air-conditioned electronics cabinet
Electronic function monitoring
Stop function upstream of machine infeed in response to fallen-over containers
Rejection unit with retaining bar or clamping starwheel

This unit has been in operation only with PET bottles sizes 0.5 liter (four different types), 1.5 liter ( two different types) 1.0 and 1.25 liter bottles and it has been in operation since 2002 and is still in very good operational condition. Handling tools for above mentioned PET bottles will be a part of delivery.

Technical specification:
Manufactured by: Krones AG, Germany
Manufactured in: 2002
Model: K 719-555
Nominal output: up to 72000 bph
Actual output: 35000 bph (with clamping starwheel)
Inspection units (PET)
For foreign containers P.E sensor and camera
Base 1 Camera
Variostation 1 Camera
- sealing surface
Residual liquid High frequency + infrared
Side wall Camera
Optimized scuffing Camera
Variostation 2 Camera
- Base 2
- inner side wall
- full thread
Variostation 3 Camera
- full thread
- lateral neck finish
- inner side wall
Variostation 4 Camera
- sealing surface
- lateral neck finish
Equipment for SaleGeneral Industry Textile Machinery Process Equipment Energy & Power Wood Working.

ating line is delivered by Finnish Elmont Oy and it consist of 59 separate dipping tanks, 6 material handling cranes and related process and automation equipment. We have the dipping tanks and material handling cranes in our store for sale. Dipping tank materials are AISI 316, SS, PP, HST and PP. All tanks are 2200 mm long and 1250 mm height, widths varies from 450 to 1740 mm, volumes from 1213 to 4016 liters. All tanks are in good condition.

The cranes are designed for those tanks and we have 6 pcs of them. Cranes have 0.25 kW gear motors and control panels. Structure is made of steel and they are in good condition.

If you are looking for such equipment, please contact us and we are pleased to give you more deep information.

Good condition filtration press made ny German MSE Filterpress GmbH in year 1997. The press has 33 plates of size 630 x 630 mm, cace thickness 25 mm. Includes own hydraulic system and control cabinet.

The equipment is manufactured by German MSE Filterpress GmbH, year 1997. Manufacturer’s type KFP 630-40-25K-MPN+DLMP. Structure is made on normal construction steel, plate size is 630 x 630 mm. The filter plates are pressed with single acting hydraulic cylinder with inbuilt hydraulic pump-motor. Product is fed in a central sludge feed inlet with flange connection and each pressing unit has its own outlet for the liquid filtrate which is them collected in one outlet channel. The cake will be disposed under the press. The unit has its own control panel attached to the equipment.

Technical data:
Manufacturer: MSE Filtterpress GmbH
Year of manufacture: 1997
Manufacturers type: KFP 630-40-25K-MPN+DLMP
Plate size: 630 x 630 mm
Number of plates: 33
Cake thickness: 25 mm
Hydraulic pressure: 380 bar max
Filtration pressure: 15 bar.

The main description of the plant equipmet is:

1. Brew House Make & Capacity:
Steinecker1995 -1999
5 brews/d, 450-500 hl/brew. for 7000 kg malt, 3850 Raw grain
Cast-out quantity: 500 hl, 16,5° Plato
8 Brews/ 24 hours, annual capacity 0.85 Mhl
Controls are based on Siemens S5 and S7 PCS with, Botec Control system, PC Windows 2000 (Steinecker)
Laboratory yield = 97.1% (2.1.09 – 28.5.09, 837 brews)

The Brewhouse was installed in 1996 - 1999 by Steinecker to a high standard of control and automation and it contains the following main equipment:

Wet Conditioning Mill, capacity 20 tons/hour and it is fully overhauled 2008

Configuration, main characteristics:
1 wet mill plant: 20 t/h
1 mash tun kettle plant: V=550 hl
1 lauter tun plant: D=7200mm
1 weak wort tank: V=155 hl
1 pre run vessel: V=640 hl
1 CIP- water distributor
brew/whirpool kettle hot wort max. 520 hl (1 brew / 5 hours)
wort cooling 400 hl/h, 10°C

- Mash Kettle, a jacketed vessel 550 hl
- Enzyme Dosing pot and pump
- Lauter Tun complete with spent grain tank and Pondorff pneumatic grains transfer. Tun capacity 814 Hl and diameter 7200 mm, Solids capacity of 7000 kg malt and 3850 kg raw grain. Complete with internal rakes and scrapers
- Pre Run Vessel complete with internal heater , volume 640 hl
- Wort Boiler/ Whirlpool, gross volume 757 hl net 520 hl
- Wort Cooler with aeration – GEA supplied plate heat exchanger (YOM 1990) – rated at 450 Hl/hr cooling the wort from 95oC down to less than 10oC. Cooling achieved with brewing water and then chilled water. Aeration achieved by use of a sintered disc and static mixers, and controlled manually using mass flow meters
- 2 Hop Pellet Tanks
- 2 Hop Oil Tanks
- Brewhouse Weak Wort Tank, volume 150 hl
- Alfa-Laval Decanter, year 2008, capacity 100 hl / h
- 2 Weak Wort Tanks, volume approx 80 hl each
- Gypsum Tank, volume approx 40 hl
- Wet starch tank – volume 100 hl
- Spent Grains Silo
- Spent Grains Drying System
- Bulk Acid tank – plastic tank with integral bund and dosing pumps

The line is designed to fill beer in to three different type of 0,33 litre glass bottles, label the bottles neck around and lower body small around and pack the bottles in to 4 x 6 bottle cartoon boxes. This bottling line capacity is 20000 bph. Clean glass bottles were brought on wooden pallets to depalletizer which feed them to the filling lines. Innofill DMG bottle filling machine and Handtmann MMS filtration system are located in a clean air room. KHS lamella conveyor system for bottle transport and cartoon boxes. The equipment were totally delivered by German KHS in year 2003, most of machines manufactured in year 2002. All control units are Siemens Simatic S7 model with remote connection. The line was shut down in year 2008 and it is still installed and in very good operational condition.

Main equipment are:
- Bottle Depalletizer KHS AL, semiautomatic
- Micro Filtration Handtmann MMS 130
- Filling Equipment KHS Innofill DMG (rinsing, filling and capping)
- Labelling Machine KHS Innoket 2060
- Cartoon Box Forming Machine KHS Innopak CA-1
- Bottle Packing Robot KHS Innopak SP 1200
- Box Marking System
- Case Sealer KHS Innopak CV.

Rotary Lube Blower / Vacuum compressor KAESER EB 420 C û 38 m3/min, 53 kPa

There are two identical sets of oil-free, 2 lobe rotary blowers, made by Germand Kaeser Kompressoren GmbH in year 2005 with accessories. Manufactures type is Kaeser ED 420 Compact Omega Pluss 53 and accessories include a control cabinet with two inverters and programmable Kaeser Start Control STC 30 unit, totally 6 preliminary intake air filters and 3 final air intake filters with their steel supports. The rotary blower units have removable sound enclose for noise insulation. Operation of the equipment was stopped in year 2007, total running hours approx 7000 and therefore they are in excellent operational condition. In addition, we can offer you service maintenance by the manufacturer at separate cost.

This equipment is suitable for demanding dust collection and pneumatic transportation of various products due to oil free operation. For pneumatic transport application some changes in filters and other parts are needed.
The rotary lobe has two blower shafts with high efficiency Omega profile in a blower block. The rotary lobe and the block have a very small distance and they are not touching each other's and therefore there is no need for lubrication oil. The rotors are driven by high efficiency electric motor via belt connection and they both are installed on the same base frame. . The inlet and discharge silencers are designed to be effective at all frequencies and are eminently suited to variable speed . Higher rotational blower speeds produce high volumetric efficiencies, which in turn lower discharge temperatures and power consumption. The Compact Range ensures that all serviceable items are accessed from the front panels of enclosures.
The preliminary intake air filters are combination of cyclone and bag filter and it removes most of the dust from inlet air. Fine filter is a combination of cyclone and 138 ceramic fine filters which removes fine dust very effectively.

Technical Data
Manufacture's type: EB 420 Compact Omega plus 53
Manufactured in year: 2005
Suction capacity with max vacuum:38,0 m3/min
Power demand max: 40,3 kW
Rotor's rotation speed 4120 rpm
Max suction vacuum: 0,53 bar (abs.)
Discharge pressure: 1,0 bar (abs.)
Max pressure increase: 470 mbar
Temperature rise max -t: 82 K
Electric motor: 45 kW û 50 Hz / 400/690V û 83/48 A
Electric motor nominal speed:2965 rpm
Protection class: IP 55
Inverters: Mitsubishi FR-F740-01160-EC
Case ventilation fan: 370 W û 50 Hz / 230 / 400V
Weight blower with the case:1120 kg
Blower case main dimensions:1.8 x 1.7 x 1.8 m (K x L x S)
Noise level: 99 dB (A)
Noise level with the case: 84 dB (A).

ELMO-G Blower - Vacuum pump 1000 m3/h

The blowers are made by German ELMO Vacuum Technology GmbH, a Siemens company in year 2002 and they are single stage, gas ring type. The vacuum pumps are in good operational condition. We have three identical pump units and originally the pumps were in dust suction operation and therefore the delivery includes 3 pcs high efficiency cyclone type dust filter with electric discharge vibrators. Motor speed is controlled with individual inverters. Units can be sold separately.

ELMO-G vacuum pumps can be used for suction operation or as compressors in pneumatic transportation system. They have side-channel principle using gas ring as a sealing and the gas flows through the compressor along a helical trajectory and is repeatedly accelerated and thereby repeatedly compressed according to the required operating point. The blowers are oil-free and thus suitable for various applications. The blowersÆ have both suction and discharge noise silencer. For pump curves, both in suction and compression, as well as additional information please contact us.

Technical Data:
Manufacturer's type:ELMO 2BH1943-1GC36
Year of manufacture:2002
Suction capacity with max vacuum:16,7 m3/min (50Hz)
Suction capacity with max discharge pressure:21,5 m3/min (50Hz)
Max pressure difference in vacuum operation:0,30 bar (50 Hz)
Max pressure difference in compression operation:0,35 bar (50 Hz)
Inverter:Danfors VTL 6000 HVAC
Blower's rotation speed2920 rpm / 50 Hz and 3520 rpm / 60 Hz
Electric motor (Siemens):50 Hz: 21.0 kW û 300/690V û 39.5 / 23.0 A
60 Hz: 24.2 kW û 460 V û 41.0 A
Protection class:IP 54.

Industrial Crane Konecranes CTX 10 t, Dual Bridge with 33.6 m span

The crane was manufactured by Konecranes Oyj in 2001 and the operation was stopped in year 2006. The equipment was regularly serviced by the manufacturer and is thus in excellent operating condition. The crane is still installed in its original place and can be tested on any time. The double bridge is welded housing construction equipped with one double speed wire hoists and a motorized rail equipment on both ends. The crane has both the local wire connected control unit as well as the wireless remote controller. On the bridge there is a service platform and the local LV û and control cabinet. All electric motors are dimensioned in accordance with Industrial Heavy Duty ED classification. The equipment includes the crane moving rail which will be sold separately.

Technical data:
Manufacturer's type:CXTD10t x 33.6m Hol: 6.1m
Lifting capacity:10 000 kg
Span distance:33.55 m
Lifting class:FEM M5 (2m)
Bridge structure:Welded case
Total weight:Approx 22 000 kg
Type of wire hoist:XL 404N40BDA4
Lifting height:6.1 m
Lifting speeds:8.0 and 1.3 m / min
Wire hoist speeds:32 and 8 m / min
Bridge speed:Inverter controlled, max 40 m / min
Wire hoist lifting motor:Double power 15 and 2.5 kW (60% ED)
Wire hoist moving motors:2 x 0.65 kW (40% ED)
Bridge moving motors:2 x 1.8 kW (40% ED)
Total power need:19.9 kW / 400 V / 50 Hz
Crane moving rail:60 x 40 cm, length 2 x 140 m.

Compressor single stage, standard speed oil-injected rotary screw compressor with manufactured by German company Drucklufttechnik GmbH in year 2002. The complete unit consists of intermediate pressure vessel and Ultratroc - air dryer all delivered same time as the compressor. The unit is controlled by modern DELCOS 3000 control unit. The total unit has 30320 operating hours, the unit has been regularly serviced by a compressor service company and is in good operational condition. The compressor is single-stage, double screw, V-belt driven electric motor drive compressor which has oil cooler and thermostat controlled water - air after cooler on discharge of the pressurized air. The operations were stopped in year 2006 but the compressor and other equipment are still installed and ready for test run.

Technical data:
Compressor type:CompAir L90 7,5A
Capacity:16.1 m3/min, 7.5 bar
Comp. electric motor:90 kW - 400/415 V û 50 Hz
Air cooler electric motor:3.0 kW - 400/415 V û 50 Hz
Compressor weight:2380 kg
Compressor dimensions:2.4 x 1.4 x 2.0 m (W x L x H)
Air dryer type:Ultratroc SD 1350 û type 422
Air dryer air volume:22.5 m3/min
Total power requirement of dryer:2.4 kW
DryerÆs refrigerant:Type R134 a û filling 3.5 kg
DryerÆs dimensions:1200x900x800 mm, weight 185 kg
Int. mediate air pressure vessel:Volume 2 m3, 10 bar, made by Galvanoimis Oy.

The boiler is a three-pass, fire-tube steam boiler made by Finnish Ahlström Themoflow in year 1990. The boiler has max operating pressure16 bar with 205 C steam temperature and it is equipped with exhaust gas economizer for preheating incoming feed-water and modulating heavy fuel oil burner. It's has a large 15.2 m3 water volume which allows big momentary changes in load. Other benefits include simple structure, long operating life, reliability and ease of service and maintenance. The boiler is in good operational condition. Feed water pumps and feed water tank with aerator are available for separate request and price.

Technical Data:
Manufacturer: Ahlström Thermoflow, Kaarina
Manufacturing year: 1990
Capacity: 3.3 MW
Water volume: 15.2 m3
Steam characteristics: Max 16 bar, at 205 C temperature, saturated
Oil Burner: Weishaupt Monarch RMS 50/2 A - ZM (YOC 1990)
Oil feeding: 140 - 490 kg/h.