Good condition filtration press made ny German MSE Filterpress GmbH in year 1997. The press has 33 plates of size 630 x 630 mm, cace thickness 25 mm. Includes own hydraulic system and control cabinet.
The equipment is manufactured by German MSE Filterpress GmbH, year 1997. Manufacturer’s type KFP 630-40-25K-MPN+DLMP. Structure is made on normal construction steel, plate size is 630 x 630 mm. The filter plates are pressed with single acting hydraulic cylinder with inbuilt hydraulic pump-motor. Product is fed in a central sludge feed inlet with flange connection and each pressing unit has its own outlet for the liquid filtrate which is them collected in one outlet channel. The cake will be disposed under the press. The unit has its own control panel attached to the equipment.
Technical data:
Manufacturer: MSE Filtterpress GmbH
Year of manufacture: 1997
Manufacturers type: KFP 630-40-25K-MPN+DLMP
Plate size: 630 x 630 mm
Number of plates: 33
Cake thickness: 25 mm
Hydraulic pressure: 380 bar max
Filtration pressure: 15 bar.
Compressor single stage, standard speed oil-injected rotary screw compressor with manufactured by German company Drucklufttechnik GmbH in year 2002. The complete unit consists of intermediate pressure vessel and Ultratroc - air dryer all delivered same time as the compressor. The unit is controlled by modern DELCOS 3000 control unit. The total unit has 30320 operating hours, the unit has been regularly serviced by a compressor service company and is in good operational condition. The compressor is single-stage, double screw, V-belt driven electric motor drive compressor which has oil cooler and thermostat controlled water - air after cooler on discharge of the pressurized air. The operations were stopped in year 2006 but the compressor and other equipment are still installed and ready for test run.
Technical data:
Compressor type:CompAir L90 7,5A
Capacity:16.1 m3/min, 7.5 bar
Comp. electric motor:90 kW - 400/415 V û 50 Hz
Air cooler electric motor:3.0 kW - 400/415 V û 50 Hz
Compressor weight:2380 kg
Compressor dimensions:2.4 x 1.4 x 2.0 m (W x L x H)
Air dryer type:Ultratroc SD 1350 û type 422
Air dryer air volume:22.5 m3/min
Total power requirement of dryer:2.4 kW
DryerÆs refrigerant:Type R134 a û filling 3.5 kg
DryerÆs dimensions:1200x900x800 mm, weight 185 kg
Int. mediate air pressure vessel:Volume 2 m3, 10 bar, made by Galvanoimis Oy.
Used industrial equipment and production lines, power generation equipment, dairy equipment, petrochemical filling lines, packing equipment, industrial processes, bewerage industry equipment.
Iron ores are rocks and minerals from which metallic iron can be economically extracted. The ores are usually rich in iron oxides and vary in colour from dark grey, bright yellow, or deep purple to rusty red. The iron itself is usually found in the form of magnetite, hematite, goethite, limonite or siderite.
The primary use of iron ore is in the production of iron. Most of the iron produced is then used to make� steel.� Steel� is used to make automobiles, locomotives, ships, beams used in buildings, furniture, paper clips, tools, reinforcing rods for� concrete, bicycles, and thousands of other items.
Iron ores are rocks and minerals from which metallic iron can be economically extracted. The ores are usually rich in iron oxides and vary in color from dark grey, bright yellow, deep purple, to rusty red. The iron itself is usually found in the form of magnetite (Fe3O4), hematite (Fe2O3), goethite (FeO(OH)), limonite (FeO(OH).n(H2O)) or siderite (FeCO3). Hematite is also known as "natural ore". The name refers to the early years of mining, when certain hematite ores contained 66% iron and could be fed directly into iron making blast
Iron Ore Pellets:
Pellets are small balls of iron ore used in the production of steel. They are made with technology that uses the powder that is generated during the ore extraction process, once considered waste.
The pellets are used in the production of steel which is used in the construction of bridges, cars, planes, bicycles, household appliances and much more.
Product Type: IRON ORE PELLETS
Fe (T) 64 %
Si02 1.150 %
Fe0 0.75 Max
Ti02 0.021%
Al2O3 0.319 %
Ca0 1.170 %
P 0.032 %
S 0.031 %
V205 0.004 %
Cu 0.057 %
N2O 1.290 %
Mg0 0.069 %
CCS 309
Size 16-19 mm - 7 %
09-16 mm -91 %
06-09 mm 2 %
Tumbler Index- for above 6.3 mm 96.2 % -� 95 % min
Abrasion Index â??for 0.5 mm 3.8 % - � 4 % max
Sticking Index @950 deg C 20.1 %
Bulk Density 2.17 %
Compression Strength 270 Kg / Pellet � / � 150 kg / pellet
Fines below 5mm (-) 5 mm 3 % max
Reducibility index 55-65 %
Iron ores are rocks and minerals from which metallic iron can be economically extracted. The ores are usually rich in iron oxides and vary in color from dark grey, bright yellow, deep purple, to rusty red. The iron itself is usually found in the form of magnetite (Fe3O4), hematite (Fe2O3), goethite (FeO(OH)), limonite (FeO(OH).n(H2O)) or siderite (FeCO3). Hematite is also known as "natural ore". The name refers to the early years of mining, when certain hematite ores contained 66% iron and could be fed directly into iron making blast
Iron ores are rocks and minerals from which metallic iron can be economically extracted. The ores are usually rich in iron oxides and vary in colour from dark grey, bright yellow, or deep purple to rusty red. The iron itself is usually found in the form of magnetite, hematite, goethite, limonite or siderite. The primary use of iron ore is in the production of iron. Most of the iron produced is then used to make steel. Steel is used to make automobiles, locomotives, ships, beams used in buildings, furniture, paper clips, tools, reinforcing rods for concrete, bicycles, and thousands of other item
Pellets are small balls of iron ore used in the production of steel. They are made with technology that uses the powder that is generated during the ore extraction process, once considered waste.
The pellets are used in the production of steel which is used in the construction of bridges, cars, planes, bicycles, household appliances and much more.
e equipment was manufactured by Jeffrey Rader AB, Sweden in 1995 and it is in very good operational condition. It consist of two heavy duty rolls with removable profilied surfaces which rotate towards each other and presses overzised wood chips between the profiles. Roll drives 2 x 110 kW / 1500 rpm connected with two gearboxes. Hydraulic pump 7.5 kW, capacity 220 m3/h wood chips.
The equipment was manufactured by Jeffrey Rader Inc, Sweden in year 1995, manufacturers type is DynaYield 80-300 and it is in good operational condition. The Chip Conditioner consists of two heavy duty rolls with removable profiled surfaces. They rotate towards each other and pull the oversize chips between them. The profiled surfaces are aligned so that the pyramid apexes on one roll travel in the valleys of the apexes on the adjacent roll. With normal oversize wood, the Conditioner typically generates less than 1% fines and 3% pins
The normal application for the Chip Conditioner is in a chemical pulping process, processing the oversize materials by fissuring the wood chips parallel with the grain to allow the cooking liquors to penetrate the chip, and allow the oversize chip to cook as an acceptable size chip. Another application is in a thermo-mechanical pulping process (TMP), as a preconditioning
An important feature of this machine is its ability to handle small portions of tramp without going off-line. With the so called Dynagage Conditioner, the dynamic roll is allowed to move away from the static roll, and once the tramp is through the unit, the roll automatically moves back to the proper set point without shutting down the flow and together with slow rotation speed enable were low down time and maintenance costs. Roll distance movements are made with a hydraulic system build on the equipment and controlled by 3 position sensors
More information on requests, for spam protection please introduce yourself properly.
Technical data:
Model: RDY 80-300
Manufacturing year: 1995
Capacity (throughput): 220 m3/h loose wood chips
Press roll diameter: 915 mm
Roll length: 2440 mm
Roll motors: 2 x 110 kW / 1500 rpm / 690 V – 50Hz
Press distance between the rolls: 2.2 mm
Gearboxes: 2 x Kipo Benzler TV 512
Hydraulic pump: Rexroth 200 bar with Mecman syliders
Electric motor for hydraulic pump: ASEA 7.5 kW
Weight: 33 000 kg
Length: 5083 mm
Width: 2550 mm
Height: 2400 mm.
The fan is made by German Pollrich Ventilatoren GmbH in year 2004 and it has been as a back-up emergency fan which has practically newer used and therefore the unit is new like condition. This fan was designed to blow explosive air/gas mixture (VOC) and therefore it fulfills category II 2G, temperature class 1 ATEX 95 norm of explosive proof design. The motor and fan are built on a common heavy duty frame and they are connected with a flexible coupling.
Technical data:
Manufacturer: Pollrich Ventilatoren GmbH
Year of manufacture: 2004
Fan type: VR50S11C1UK0900LG360MMUU
Manufacturing no: 123665
Volume: 10.55 m3/sec (37980 m3/h)
Max press difference: 8000 Pa (0.08 Bar)
Speed: 2980 RPM
Max gas temperature: 80 C
Power requirement: 104.6 kW
Electric motor: CEMP 132 kW / 2970 RPM
Type: AC70 315M 2
Classifications: II 2 G EEXd IIC T4 IP 55.
The boiler is a three-pass, fire-tube steam boiler made by Finnish Ahlström Themoflow in year 1990. The boiler has max operating pressure16 bar with 205 C steam temperature and it is equipped with exhaust gas economizer for preheating incoming feed-water and modulating heavy fuel oil burner. It's has a large 15.2 m3 water volume which allows big momentary changes in load. Other benefits include simple structure, long operating life, reliability and ease of service and maintenance. The boiler is in good operational condition. Feed water pumps and feed water tank with aerator are available for separate request and price.
Technical Data:
Manufacturer: Ahlström Thermoflow, Kaarina
Manufacturing year: 1990
Capacity: 3.3 MW
Water volume: 15.2 m3
Steam characteristics: Max 16 bar, at 205 C temperature, saturated
Oil Burner: Weishaupt Monarch RMS 50/2 A - ZM (YOC 1990)
Oil feeding: 140 - 490 kg/h.
Very little operated (ony 6000 hours totally!) fuel oil fired package boiler made by Högfors (nowadays Foster Wheeler) in 1988. Complete plant with combustion air fan and feed water pumps for immediate delivery, in very good condition.
Main scope of the delivery:
- Högfors 30 t/h boiler
- Oilon burner
- Economizer
- Combustion air fan
- 2 pcs of 90 kW / 25 bar KSB feed water pumps
- Fuel oil pumping unit made by Oilon
- 8 pcs of steam shoot blowers
- valves, fittings and maintenance supports .
Type of boiler Water tube type with natural circulation, with two drums
Manufacturer Kymin Osakeyhtiö, Högfors, Finland (Foster Wheeler)
Model of the boiler: H52-47-25 bar
Year of manufacturing 1980
Starting day of operation 16.11.1980
Evaporation 47 t/h saturated steam
Temperature of steam 226 oC
Effect 30 MW
Structural pressure 25 bar
Feed water temperature 120 oC
Furnace volume 74,5 m3
Surface of furnace c. 136 m2
Surface of convection part 420 m2
Surface of economizer c. 504 m2
Water volume 15,8 m3
Oil Heavy oil (POR 230)
Oil burner Saacke SKV, fully automatic, modulating
Regulating area of burner 610-3050 kg/h
Oil pumping- and pre- Oilon Osva 4000 kg/h
heating station
Feed water pumps 2 pcs + 1 pc as spare.
KSB-centrifugal pump MOVI 65/6,
massflow 59 t/h, 29,5 bar
motor 90 kW, 2900 r/min
Primary air fan Mercantile KDER 75, 37300 Nm3/h, motor 115 kW, 1500 r/min
Sootblowers Diamond Superior sootblowers 4 pcs in boiler part
Diamond Superior sootblowers 4 pcs in economizer.
Dimensions of boiler part: Height 5,2 m, Width c. 4,5 m, Length 10,0 m
Weight of boiler part c. 54 t. without water and accessories
Weight of economizer c. 15 t. without water and accessories
Boiler is suitable for gas operation by changing the burner.
The boiler has been in operation only about 6.000 hours.
Equipment for SaleGeneral Industry Textile Machinery Process Equipment Energy & Power
Gas & HFO Boilers Wind Turbines.
30 Cold Pressed Oil Suppliers
Short on time? Let Cold Pressed Oil sellers contact you.
