1.Description
Chase friction testing machine is used to evaluate the frictional characteristics of material in braking system in accordance with the SAE J661,GB 5763-2018 and GB/T 17469-2012.
Chase machine is suitable for small bench test of M1, M2, N1, O1 and O2 vehicles brake linings.
This machine is widely used for product formulation R&D, Quality control and Certification etc.
2.Principle
A constant pressure is applied to the sample,which will be pressed against the inner surface of the friction drum which rotates at a certain speed, so a friction force will be generated along the tangent direction of the contact surface. The friction
coefficient of the tested sample can be determined by measuring the pressure and friction force.
During the test, the Chase friction tester controls the temperature change at any time according to the requirements. The drum outer ring is used to assist the heating tube heating and the back suction cooling, so that the temperature change at the sample is stable and the temperature measurement accuracy is higher.
3.Features
(1)Loading by Pneumatic servo with high precision control.
(2)Temperature of friction drum is adjustable to adapt to different test requirements and different climatic condition.
(3)Rubbing speed can be set freely between 0 and 1000 RPM.
(4)The maximum load is up to 2000N.
(5)This machine is controlled by PC. Speed, loads, temperature and test time can be preset by software. Test results are saved in computer.
4.Standards
SAE J661, SAE J866, GB 5763-2018, GB/T 17469-2012,
5.Specifications
Speed 0 to 1000 RPM
Load 0 to 2000 N
Temperature 0-600 (1112)
Heating power 6KW
Friction drum Ф277mm
Power AC 380V
Weight Approximate 2100kg
1. Size of concrete specimens for compression strength test
Concrete cubic specimen: 150X150X150mm, 100X100X100mm, 200X200X200mm
Cylindrical concrete specimen: diameter 150X300mm, diameter 100X200mm, diameter 200X400mm
2. Brief introduction of concrete compressive strength test procedure
1) Placing the concrete specimen---place the test specimen on the lower bearing block. Carefully align the axis of the specimen with the center of thrust of the spherically seated block.
2) Apply the load continuously and without shock until the specimen fails and record the maximum load carried by the concrete specimen during the test. Note the type of failure and the appearance of the concrete.
3.Relative test method
GB/T 50081 standard for test method of mechanical properties on ordinary concrete
ASTM C39 standard test method for compressive strength of cylindrical concrete
ASTM E74 practice of calibration of force-measuring instruments for verifying the force indication of testing machine
4. Specifications for concrete compressive strength testing machine
Max. capacity: 3000KN( lower or higher capacity can make to order)
Grade of testing machine: grade 1
Distance between upper and lower compression platen: 320mm
Stroke of piston:50mm
Size of upper and lower compression platen:375X375mm
Weight :about 900kg
1. Introduction and test principle of compression strength measuring
The compression testing machine is to measure compression strength of corrugated boxes in the situation of pressure and protect functions of packages for the objects filled in the packages.
Test principle:
(1) Corrugated boxes compression strength test, loading to the corrugated boxes using a compression testing machine at a certain constant rate untill corrugated boxes are broken or till certain load or displacement are reached.
(2) Corrugated boxes stacking test, loading a certain force to the corrugated box using a compression testing machine untill corrugated box is broken or sustain a certain time period.
When measuring deformation of corrugated box during compression test, an original load should be set as a datum point. The datum point can refer to the following chart:
Average compression force(N)Original force(N)
101-200 10
201-1000 25
1001-2000 100
2001-10000 250
10001-20000 1000
200001-100000 2500
2. Functions of compression testing machine
This machine is applicable to metal, cementing compound, tubes, sectional bars, aerospace, petrochemical, waterproof rolls, wire and cable, textile, fiber, rubber, ceramics, food, mechanical packaging, geo-textile, film, wood, paper and other industries and quality supervision department, and it also can be used in college for teaching demonstration.
3. Specification of compression testing machine
1 Max. Load 20KN
2 Resolution of test force 1/300000
3 Resolution of displacement 0.001mm
4 Precision of crossbeam displacement 0.5%
5 Precision of deformation 0.5%
6 Measuring range of test force 1%-100%FS
7 Relative error of test force 1%
8 Relative error at zero point 0.5%
9 Speed of crossbeam 0.01-500mm/min
10 Precision of crossbeam speed 1%
11 Speed range of load 0.005%-5%FS/s
12 Precision of load speed When speed is less than 0.05FS/s, precision is within 1% of set value, when speed is more than 0.05FS/S, precision is within 0.5% of set value
13 Speed of deformation 0.005%-5%FS/s
14 Precision of deformation speed When speed is less than 0.05FS/s, precision is within 1% of set value, when speed is more than 0.05FS/S, precision is within 0.5% of set value
15 Stroke of crossbeam 900mm
16 Effective tensile height 650mm
17 Effective test span 400mm
18 Effective compression height 800mm
19 Diameter of compression platen 100mm
20 Voltage and power 220V,50Hz, 700W
21 Dimension of main machine 650X450X1650mm
22 Weight of main machine about 300kg
3. Applications of testing machine
This machine is applicable to metal, cementing compound, tubes, sectional bars, aerospace, petrochemical, waterproof rolls, wire and cable, textile, fiber, rubber, ceramics, food, mechanical packaging, geo-textile, film, wood, paper and other industries and quality supervision department, and it also can be used in college for teaching demonstration.
4. Features of testing machine
1) Adopting aluminum alloy cover, with attractive streamline structure
2) Mainly used to test mechanical properties for metal, non-metal and composite materials
3) Adopting precision auto control and data acquisition system to realize fully digital adjustment to data acquisition and control process. During test, it can test max. Bearing tensile force, compression force, tensile strength, deformation, elongation, yield point and other technical specifications
4) After test, the above parameters can be calculated automatically through main controller according to the test parameters, which are set before test and meantime display the corresponding test results. All test parameters can be saved and inquired after test, also can be printed out.
5) With remote control box to realize speed adjustment of crossbeam, flexibly and freely switched
6) With functions of automatic return to original position, intelligently, efficiently, quickly
7) With limit position function of any working position and over voltage, over current protection functions, reliable and safe
8) With many control modes of constant speed control to force, stress, deformation, strain and low cycle and user self-programming control
9) Switch among many test curves: stress-strain curve, load-deformation curve, load-displacement curve, load-time curve, deformation-time curve, displacement-time curve. Partial enlargement, overlap and comparison.
Features of plastic navigation buoys:Environmentally Friendly; Easy Maintainence; No painting, ever; High Impact Reisitance; Long Service Life
Navigation buoy is an artificial sign that helps guide the navigation of ships, locate and mark obstructions and indicate warnings.
The plastic navigation buoys are made of two parts: float section and extended tower. The float section is made of virgin PE with PU foam inside and the tower of virgin PE.
Features of Plastic Navigaiton Buoy:
Environmentally Friendly
Easy Maintainence
No painting, ever
High Impact Reisitance
Long Service Life
Customized plastic navigation buoys available. Most of the buoys are made to order and can be designed to any shape or size to meet clients' requirements.
947 Electronics Communications Suppliers
Short on time? Let Electronics Communications sellers contact you.
Impact specimen gap hydraulic broaching machine is the only instrument gap for processing the qualified sample except the optical curve grinding machine. Because of processing theory once, the identity of processing the gap is very nice. This broaching machine adopts w18cr4v manufacturing, high hardness, wear resistance, and every tool can process the sample as many as 20, 000.
Brief: this cnc plasma table for sale here is model. Eagletec ea-1540pl. Plasma table size is 1500x4000mm, the table size here refers to the actual cutting size. In other words, it can cut anywhere of sheet metal in the range of 1500x4000mm. To match such a big cutting size, we adopted 200amp plasma power source for this cnc plasma table. In this way, its maximum quality cutting thickness can be up to 40 mm for all kinds of sheet metal includes carbon steel, stainless steel, aluminum, iron, copper, brass and so on. The cnc plasma table ea-1540pl is a good cutting solution for sheet metals whose size are not over 1500x4000x40mm. If your cutting requirement is accordance with this size, then ea-1540pl is the best cnc plasam table for you with affordable price.
Arc voltage torch height controller: this cnc plasma table for sale is included t.H.C system. It ensures the quality cut
Even over uneven metal sheets. If without it, you will not get a quality cut over uneven surface.
Cable length is adjustable. Pull tight locking mechanism. Remove by cable cutters, eyes protection is necessary. Pre-numbered with consecutive, sequential digits is available. Please contact us for more colors.
SENYUAN Power Distribution Panel provides production and supply control and distribution systems to meet customer requirements. Complete advanced power distribution solutions to solve the complexity of generators and power plants.
Single genset output to load with ATS for grid
â?¢ Single genset synchronized onto grid
â?¢ Multi-Genset paralleling
â?¢ Multi-Genset paralleling and synchronization onto grid
â?¢ Multi-Genset paralleling by Bus CouplingÂ
KYN28A-12 Indoor metal-clad withdrawable switchgear
LOW-voltage combination switchgear
Shandong senyuan new energy technology co. LTD is a high-tech enterprise which produces 1MW to 100MW new energy power plant and integrated electrical control system. The total area of Sen yuan new energy industry covers an area of 76,000 square meters,There are 10 production workshops, each of which occupies an average area of 3000 square meters.
Shandong Sen source new energy equipment manufacturing Co., Ltd. has a complete enterprise GB/T 19001-2008/ISO9001:2008 version certification system (square) and China Quality Certification Center CCC certification system, the company is a high-tech enterprise, has 16 industry patents and 16 computer software copyright.
Company: Shandong senyuan new energy technology co. ,LTD
SENYUAN Power Distribution Panel provides production and supply control and distribution systems to meet customer requirements. Complete advanced power distribution solutions to solve the complexity of generators and power plants.
Single genset output to to load with ATS for grid
Single genset synchronized onto grid
Multi-Genset paralleling
Multi-Genset paralleling and synchronization onto grid
Multi-Genset paralleling by Bus Coupling
KYN28A-12 Indoor metal-clad withdrawable switchgear
LOW-voltage combination switchgear
Place of Origin: Shandong, China (Mainland) Brand Name: Zhongchuang Model Number: ZCTL-Z50kN Power: Electronic Usage: Spring Tester Product name: 50kN Computer Control Spring Compression Testing Machine Test force: 50kN Resolution of test force: 1/500000 Stroke range: 1%-100% Resolution of displacement: 0.001mm Min reading value: 10N Compression space: 600mm Diameter of plates: 300mm Test speed: 0.01-300mm/min Power supply: AC220V 10% 50Hz
Packaging & Delivery
Packaging DetailsSpecial wooden packing box for export
Delivery Time15 working days after payment
Specifications Data
Max test force50kN
Min reading value10N
Stroke range1%-100%
Resolution of test force1/500000
Accuracy of displacement0.01mm
Compression space600mm
Diameter of plates300mm
Test speed0.01-300mm/min
Power supplyAC220V 10% 50Hz
Size of valve spring tester600*400*1750mm
Weight of valve spring tester400kg
Grade of valve spring testerGrade 1
Power supplyAC220V 10% 50Hz
Testing Machine Img
The 50kN Computer Control Spring Compression Testing Machineis developed and produced by our company, which is mainly used to test the compression strength of all kinds of compression springs and elastic components.
Terrestrial series (dw3520-t, dw3220-t, dw3210-t, dw3200-t, dw3240-t), satellite series (dw3221cn, dw3222ct, dw3320fta, dw3210fta, dw3310fta, dw3200fta), hdtv series (with mpeg2 or 4), t s series.Software upgrading support by our own r & d ream
Gift & craft, pipe & fitting, garment.Specialized in international trade, trade as an agent or for self support of anything from any of possible countries