Mini controller
Charge mode, pwm
System voltage, 12v
Charge current: 8a/10a
Load output voltage: 12v
Battery type, lead acid (gel, agm, flooded)
Application ,
1. The household solar power systems
2. Small solar power system
3. The portable solar application products
1.Electronically regulated charging regime: boost and float charge
2.Emperature compensation
3.Deep discharge protection
4.Pwm series regulation, no panel short circuit
5.Fully electronically protected: panel surge voltage, wrong polarity at panel or battery,
Overload and short circuit at load
6.Led indications: charge status, soc, lvd, overload/short-circuit common positive allows
Grounding
The sc solar charge controller series is especially designed for small solar systems with the
Need of a low battery disconnect feature.Main differences to the preceding sc series: the
Regulation circuit provides now series regulation to prevent single cell overheat problems of
Shorcircuited solar panels. The terminal section has been replaced by a rugged, well profane
4mm2 terminal block. The melting fuse of the predecessor has been replaced by a fully
Electronically protected circuit.
2 leds and 1 duo led to display charging in progress, battery soc, load disconnect and overload
Status. Leisure and rural electrification systems are the typical applications for this product. It is a
Perfect solution for cost-sensitive systems which require state-of- the-art system management.
Charge modeïPWM
System voltageï12V
Charge current: 8A/10A
Load output voltage: 12V
Battery typeLead acid (GEL, AGM, flooded)
Application
1. The household solar power systems
2. Small solar power system
3. The portable solar application products
1.Electronically regulated charging regime: Boost and float charge
2.Emperature compensation
3.Deep discharge protection
4.PWM series regulation, no panel short circuit
5.Fully electronically protected: panel surge voltage, Wrong polarity at panel or battery,
Overload and short circuit at load
6.LED indications: Charge status, SOC, LVD, Overload/Short-Circuit Common positive allows
grounding
Place of Origin: Fujian,China
Brand Name: UPARK
Diameter: 219mm
Height Above Ground: 600mm
Thickness: 6mm
Drainage System: No need
Material : 304 Stainless Steel
Dustproof and waterproof level: IP68
Warning: LED Light
Emergency Operation: Emergency control system to control the raising and lowering of the bollards in the event of a power failure
SSR, 0-10v- P, PI, PD, PID Or ON/OFF Hysteresis Control, Selectable Sensor Input (J type (Fe-Const), K type (NiCr-Ni), Pt100, R type (PtRh13Pt), S type (PtRh10Pt), T type (Cu-Const) ).
Supplier: Electronic control and timing devices, lighting automation: time switches and light energy management systems, process control: mini plcs, timers, and pid temperature controllers, low voltage protection and switch gear: voltage protection, frequency, thermostat & earth leakage relays, instrumentation: hour meters, impulse counters, injection moulded plastic components
Basic Info.
Model NO.: KI31
Control Type: Digital
Display Type: Blender
Material: Plastic/ Ceramic
Certification: CE/CQC/CB/UL/cUL/TUV
Usage: Temperauter Control
Type: Temperature Switch
Max Voltage: 250V
Max Current: 16A
Body Material: Bakelite or Ceramic
Temperature Characteristics: Normal Opened or Normal Colsed
Terminal Angle: Horizontal or Vertical
Terminal Type: 6.3mm or 4.8mm
Export Markets: Global
Additional Info.
Trademark: HX
Packing: Carton or According to Customers Requirements
Standard: customized
Origin: Dong Guan,Guang Dong ,China
HS Code: 9032100000
Production Capacity: 3000000 PCS Per Month
Product Description
Technical parameters:
Electrical parameters:
1)CQC, VDE, UL, cUL AC250V 50~60Hz 5A/10A/15A (Resistance load)
2)UL AC125V 50Hz 15A (Resistance load)
2. Action temperature range: -10~260Centigrade (Optional); Temperature accuracy: 10Centigrade
3. Recovery and action temperature difference: 8~100Centigrade (Optional)
4. Connection method: Insert the terminal 250# (bending angle: 0~90¡ã Optional); Insert the terminal 18(bending angle: 0~90¡ã Optional; Thickness: 0.5, 0.8mm optional)
5. Lifespan: ¡Ý 100, 000 times
6. Electrical strength: No spark or breakdown for 1min at AC 50Hz 1800V
7. Contact resistance: 50M
8. Insulation resistance: 100M
Junction method: Constant-closed: The contact point disconnects when temperature rises; And contact point connects when temperature falls;
Constant-opened: The contact point connects when temperature rises; And contact point disconnects when temperature falls.
10. Casing protective class: IP00
11. Grounding method: Connection is made between the metal casing of the temperature controller and the metal part of the grounding device.
12. Installation method: Installed for KI031 series: General moving ring, mini round moving ring, flat moving ring general aluminum cover with mounting hole, extra length aluminum cover with mounting hole
Office Equipment Snap-action Thermostat
Applications of KSD301 Thermostat
1. Water dispenser, Electric heater, Sandwich toasters, Dishwashers, Dryers, Disinfection cabinet, Microwave ovens, Electric coffee pot, Electric caldron, Refrigerator, Air conditioning gluing machine
2. Office equipment
3. The seat heaters.
1. 250V15A thermostat
2.Plastic body or ceramics body
3.Normal close or normal open
4. VDE TUV UL CE Certificate
fixation of the working temperaturing
reliable snap action
perdurable
less radio interference
Technical parameters:
Electrical parameters: 1)CQC,VDE,UL,CUL AC250V 50~60Hz 5A/10A/15A (Resistance load)
2)UL AC125V 50Hz 15A (Resistance load)
2.Action temperature range: 45~160 (Optional); temperature accuracy:
3.Recovery and action temperature difference: 8~100 (Optional)
4.Connection method: Insert the terminal 250# (bending angle: 0~90deg optional); Insert the terminal 187# (bending angle: 0~90deg optional; thickness: 0.5, 0.8mm optional)
5.Lifespan: over100,000 times
6.Electrical strength: No spark or breakdown for 1min at AC 50Hz 1800V
7.Contact resistance: less than 50m
8.Insulation resistance: less than100M
Junction method: Constant-closed: the contact point disconnects when temperature rises; and contact point connects when temperature falls;
Constant-opened: the contact point connects when temperature rises; and contact point disconnects when temperature falls.
10.Casing protective class: IP00
11.Grounding method: Connection is made between the metal casing of the temperature controller and the metal part of the grounding device.
12.Installation method: installed for KI031 series: general moving ring, mini round moving ring, flat moving ring general aluminum cover with mounting hole, extra length aluminum cover with mounting hole
Structure and application:
KI-32 serial products are the temperature controllers taking bimetallic strip as the temperature-sensing unit. In case of normal operation the electrical appliance, the bimetallic strip is in a free state; the contact point is in a state of close/open. When the temperature reaches the action temperature, the bimetallic strip performs quick action generates caused by internal stress due to heating; open/close the contact point; disconnect/connect the circuit; thus, the temperature is in control. When the electrical appliance is cooled to the recovery temperature, the contact point automatically opens/closes to recover normal operation state.
Widely used in electrical heating appliances like water dispenser, water heater, sandwich bread baker, dishwasher, dryer, sterilizing cupboard, micro-wave oven, electric heating coffee pot, electric cooker, refrigeratory, air-conditioner, laminator, heater of auto seat.
Characteristics:
Stable performance, high accuracy, small size, lightweight, high reliability, long lifespan, less interference to radio
Precautions:
1.When adopting contact temperature sensing installation, the surface of the metal cover is required to be securely contacted with the installing surface of the controlled device. For ensuring the temperature sensing effect, it is required to coat thermal conductive grease or other similar thermal conductive medium on the surface of temperature sensor.
2.For reliable performance, collapse, loose or distorted top part of the cover is prohibited during installation.
3.Liquid inleakage into the controller, crackle in the casing and unauthorized change of external terminal position are prohibited.
4.When the product is used in the circuit with maximum current of 5A, the cable with copper core at section 0. 5-1mm2 is required for connection; When the product is used in the circuit with maximum current of 10A, the cable with copper core at section 0.75-1.5 mm2 is required for connection;
5.The product should be kept in a clean, dry and corrosive gas-free warehouse with good ventilation and at relative humidity below 90%, environment temperature below 40.
Passed certifications :CQC UL VDE TUV SGS.
