Rust-Oleum Specialty Mirror Effect - 267727

Ritver Special Effect Paint

Crackle Effect Decorative Paint

Decorative Special Effect Paint

Decorative Special Effect Paint 2
Multicopearlo

* PHOSCAST
Phoscast : Phosphate Bonded Castables

* PURPOSE
customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system.

BACKGROUND

* Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles.

* GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates.
Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion

* Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected.

APPLICATION
Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.

This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites.

Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature.
Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts.

PREPARATION OF FURANE MORTAR :
Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life.
Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.

Fabric
Roof:500g/m�² PVC UV Waterproof
Sidewall:380g/m�² PVC UV Waterproof
PVC church window

Frame
Pole: 38x1.0mm
Connector:42x1.2mm
Ground frame + reinforcement bar
Anti rusted galvanized pipe or powder coated steel pipe
Size

Width:6.0m Length:12m
Sideheight : 2m
Center height :3.05m
Ground area: 72sqm

*The engine adopts famous brand engine, 100% inspection before delivery.
*The Snow Cleaning Machine adopts full metal jacket design,after oxidation spray,anti-corrosion rust proof,long service life.
*Double LED lamp of operation panel, greatly improving the workers efficiency and safety at night and early morning.
*The Snow Cleaning Machine uses monolithic auger design, low cost of vulnerability consumption and easy replacement.
*The Snow Cleaning Machine has the advantages of fashion appearance,mult functions, light and flexibility,simple operation.

At Gremlog Trading DMCC, we're proud to offer a sustainable alternative for spent refractory bricks. Instead of discarding them, we recycle these bricks into valuable raw materials with various applications. Our recycled refractory bricks can be used in powder coating, road-base aggregate, metallurgical processes, as slag conditioners, and even as feedstock for cement production. This not only reduces waste but also provides cost-effective options for industries. Moreover, these recycled materials can be directly reused in the manufacturing of new refractory bricks, closing the loop on sustainability. Join us in our mission to promote environmental responsibility while meeting your industrial needs. Contact Gremlog Trading DMCC today to learn more about our Recycled Spent Refractory Bricks.