(Mmp )Methyl 3-Methoxypropionate

Waterborne Acrylic Modified Saturated Polyester Resin


Can be cured at between 120 150. Even higher temperature, it has good yellowing resistance. It is suitable for coil coating and can coating. It has very good results for dipping primer applications. It is also for clear gloss protective coating.



Performance Advantages:

Low odor
LOW VOC
Non yellowing, even at high temperature curing
Good hardness development


Applications:

All kinds of baking systems
Metal primer and topcoats
Industrial applications
Spray, roller, brush or dipping can be used.



1, Product Composition:

Waterborne Acrylic Modified Saturated Polyester Resin, Cosolvent

2, Typical Data:



Type of polymer Waterborne acrylic modified saturated polyester resin
Non-volatile(%) 70±2
Viscosity( 25, mpa*s) 30-70*
PH ----
Neutral.agent Non neutralization
OH value on solids (mgKOH/g) 105
Air dry Inapplicable
Cross-Linking with amino resin Applicable
Grinding Applicable
Drying speed better
Corrosion resistance better
weatherability better
PS:The Viscosity with*is measured in the case of the resin diluted by equivalent amount of propylene glycol methyl ether



3, Product Properties:

Good hardness (>4H), high gloss;

Good flexibility;

Good solvent resistance;

Low temperature fast cross-linking (110. 20minutes);

Excellent shear stability, can be grinded with dispersions directly.

4, Instructions:

WL-182 can be diluted with water after neutralization by N,N-dimethyl ethanolamine the amount of which is about 4-5%of WL-182.It has tocombine waterborne amino resin to make baking coating. The suggested amount is about 20-30% of WL-182 by weight. The baking temperatureis above 120. The baking conditions and film properties are related with the amino resins used. Right amount of waterborne acidic catalysts canbe added when using methyl etherified amino resin(recommended adding amount is 0.5-1% of WL-182), which can accelerate solidifying.

PH value of the coating system can always be adjusted with organic amine or ammonia. Viscosity of the dispersion will increase as the PH valueincreases. The resin can help to wet pigments, so wetting agent may reduce.

5, Storage:

It is suggested that the product should be stored in a cool and dry weak alkaline place. The quality guarantee period is 6 months, and the expiredproducts can still be used after passing the inspections.

6, Applications:

Amino-baking top coatings.

7, Note:

The specification is a general introduction to the products of our company. It will be adjusted with the product improvement. Please contact with thecompany to obtain the latest product description.

Waterborne Acrylic Modified Saturated Polyester Resin


Can be cured at between 120150. Even higher temperature, it has good yellowing resistance. It is suitable for coil coating and can coating. It has very good results for dipping primer applications. It is also for clear gloss protective coating.



Performance Advantages:

Low odor
LOW VOC
Non yellowing, even at high temperature curing
Good hardness development


Applications:

All kinds of baking systems
Metal primer and topcoats
Industrial applications
Spray, roller, brush or dipping can be used.



1, Product Composition:

Waterborne Acrylic Modified Saturated Polyester Resin, Cosolvent

2, Typical Data:



Type of polymer Waterborne acrylic modified saturated polyester resin
Non-volatile(%) 70±2
Viscosity( 25, mpa*s) 30-70*
PH ----
Neutral.agent Non neutralization
OH value on solids (mgKOH/g) 105
Air dry Inapplicable
Cross-Linking with amino resin Applicable
Grinding Applicable
Drying speed better
Corrosion resistance better
weatherability better
PS:The Viscosity with*is measured in the case of the resin diluted by equivalent amount of propylene glycol methyl ether



3, Product Properties:

Good hardness (>4H), high gloss;

Good flexibility;

Good solvent resistance;

Low temperature fast cross-linking (110 20minutes);

Excellent shear stability, can be grinded with dispersions directly.

4, Instructions:

WL-182 can be diluted with water after neutralization by N,N-dimethyl ethanolamine the amount of which is about 4-5%of WL-182.It has tocombine waterborne amino resin to make baking coating. The suggested amount is about 20-30% of WL-182 by weight. The baking temperatureis above 120â??. The baking conditions and film properties are related with the amino resins used. Right amount of waterborne acidic catalysts canbe added when using methyl etherified amino resin(recommended adding amount is 0.5-1% of WL-182), which can accelerate solidifying.

PH value of the coating system can always be adjusted with organic amine or ammonia. Viscosity of the dispersion will increase as the PH valueincreases. The resin can help to wet pigments, so wetting agent may reduce.

5, Storage:

It is suggested that the product should be stored in a cool and dry weak alkaline place. The quality guarantee period is 6 months, and the expiredproducts can still be used after passing the inspections.

6, Applications:

Amino-baking top coatings.

7, Note:

The specification is a general introduction to the products of our company. It will be adjusted with the product improvement. Please contact with thecompany to obtain the latest product description.

One-part Waterborne Epoxy Ester Resin WL-172


epoxy coating contains the following added features:

Extremely Long Lasting
Flexible & Durable
Water resistant
High-Gloss
Heat Resistant
Economical
Reduces Maintenance Costs
Lead-free
Nontoxic

Rustproof
One Application Only
Acid & Saltwater Resistant
Protects Against Environmental Hazards
High Adhesion



1,Product Composition:

Waterborne Epoxy Ester Resin, Cosolvent, Neutralizing Agent, Water

2,Typical Date



Type of polymer Waterborne epoxy ester resin
Non-volatile(%) 70�±2
Viscosity( 25â??, mpa*s) â?¤200*
PH ----
Neutral.agent DMEA
OH value on solids (mgKOH/g) ----
Air dry Applicable (Oxidation Cross-linking)
Cross-Linking with amino resin Inapplicable
Grinding Applicable
Drying speed better
Corrosion resistance better
weatherability better
PS:The Viscosity with*is measured in the case of the resin diluted by equivalent amount of propylene glycol methyl ether



3,Product Properties:

Excellent anticorrosion performance, especially for the preparation of anti-rust base coating;

Fast drying speed, good hardness;

Excellent salt fog-spray resistance and early water resistance:

Good storage stability;

Excellent shear stability, can be grinded with dispersions directly.

4,Instructions:

WL-172 can be diluted with deionized water or lower alcohol or alcohol ether to white emulsion. It can be dried by oxidation cross-linking addingoily/water driers at normal temperature or low-temperature baking. The oily driers need to be diluted by the solvent such as butyl alcohol or ethanolfor use.

The water dispersion of WL-172 is stable at neutral or slight alkaline conditions pH value has to be carefully observed in coating production sinceprecipitation may occur if acidic pigments like carbon black are used in the system. PH value of the coating system can always be adjusted

triethylamine or N, N-dimthylethanolamine. Viscosity of the dispersion will increase as the PH value increases.

5,Applications:

Air-drying or low temperature baking antirust coatings.

6,Note:

The specification is a general introduction to the products of our company. It will be adjusted with the product improvement. Please contact with thecompany to obtain the latest product description.