The large diameter insulating joint, produced by Shenyang Wensheng, is suitable among transportation pipeline of gas and adjusting pressure, measuring and storage. It mainly insulates each part of transportation pipeline of gas, equipment and pipeline, to prolong the use life of pipeline and equipment.
Application field:
Oil, gas, water, pulp; the suitable temperature is from -40? to 100?
Character of the large diameter insulating joint:
1 The large diameter insulating joint produced by our company can take reliable work under the required temperature and pressure of transportation medium, and has enough strength and sealing performance;
2 It has reasonable structure, which is simple to dissemble and replace part;
3 It has electrical insulation performance required by the project.
Pipe fittings are the general names of parts and components that play the role of connection, control, direction change, diversion, sealing and support in the pipeline system. Steel fittings are pressure fittings. According to the different processing technology, it is divided into four categories, namely, butt welding pipe fittings (divided into weld and no weld), socket welding and threaded pipe fittings, flange pipe fittings.
According to the application:
1. pipe fittings for connecting pipes are: flanges, live joints, pipe hoops, clamps, clamps, throat hoops, etc.
2. changing the direction of the pipe: bends, bends.
3. pipe fittings changing pipe diameter: variable diameter (different diameter pipe), different diameter elbow, branch pipe table, reinforcing pipe.
4. pipe fittings with additional piping branches: three links, four links.
5. pipe fittings for pipe sealing: gasket, raw material belt, thread, flange blind plate, pipe plug, blind plate, head, welding plug.
6. pipe fittings for pipe fixing: clasp, hook, ring, bracket, bracket, pipe clamp, etc.
According to the connection :1, welded pipe fittings 2, threaded pipe fittings 3, clamping pipe fittings 4, clamping pipe fittings 5, socket pipe fittings 6, rubber ring connection pipe fittings
According to the material divided into 1, cast steel pipe fittings 2, forged steel pipe fittings 3, alloy pipe fittings 4, stainless steel pipe fittings.
Pipe fittings are widely used in municipal, petrochemical, west-to-east gas transmission, ships and nuclear power.
We supply various types of UPVC pipe fittings including welded fittings there are two kinds of welded and nonwelded socket welded and threaded fittings flange fittings
Ball valve straight pipe straight elbow forward Tee pipe clamp abnormal straight reducing elbow cross loose jointpipe cap copper inner wire straight copper inner wire Tee outer wire direct head loose joint direct head loose elbow
1 Fittings used for connecting pipes are flange loose joint pipe hoop clamp sleeve throat hoop etc
2 Fittings change the direction of the pipe elbow bend pipe
3 Fittings change the diameter of the pipe reducing diameter reducing pipe reducing elbow branch pipe reinforcing pipe
4 Fittings increase the pipe branch tee crossing
5 Fittings for pipe sealing gasket raw material belt thread flange blind plate pipe plug blind plate head welding plug
6 Fittings for pipe fixing clamp ring tow hook hanging ring bracket bracket pipe clamp etc
Like wax candles, Rouseki (Pyrophyllite) is white and semi-transparent, and has a waxy texture when touched. It is very brittle, and tends to crack largely along the stone joints. Up close, this stone looks grayish white, but may look blue from a distance.
The ore looks so similar to pottery stone ore that they cannot be distinguished. But there is a difference in their texture, color, and how they crack, and with experience, their differences become more visible. They not only look and feel different, but their applications and properties also differ significantly.
It's used as Firebricks, crucibles, glazes, fire-resistant powders, etc.
* K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors.
It is also used for jointing chemical resisting stoneware pipes.
K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles.
The concrete surface needed protection should be dryed, clean and rough.
The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner.
When Bedding and Jointing Materials are the same.
On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints.
The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water.
Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic.
When Bedding and Jointing Materials are Different.
Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR
A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions.
PREPARATIONS OF MORTAR :
* Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan.
* Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar.
* In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared.
* The cement mortar will be used before it starts setting.
Thermotax is a ready to use air setting refractory mortar. It is air setting mortar having good strength on air drying, forming strong joints & conferring an almost monolithic structure to the fire brick work. Moreover, it is highly suitable for Insulation brick lining work as well as refractory Brick lining work.
DIRECTIONS FOR USE:
- Shake well before using.
- Keep container closed when not in use.
- Set time is the time required before joint can safely be handled.
- Cure time is the time required before joint can be pressure tested.
1. Cut pipe square with saw or hand cutter. Remove all burrs.
2. Check dry fit of pipe and fitting. Pipe should easily go A1/A3 to A1/A2 way into fitting. If pipe bottoms into fitting it should be very snug.
3. Pipe and Fitting should be free of dirt, grease and other foreign materials. If necessary clean pipe and fitting using RPC-WELD Pipe Cleaner. Primer is highly recommended for 3 and larger diameter installation. Apply liberal coat. Primer will start softening surface of pipe and fitting thus ensuring superior joint.
4. Use applicator supplied with the can or suitable applicator at least A1/A2 the size of the pipe diameter.
5. Apply liberal coat of cement to the pipe (equal to depth of fitting) and adequate coat inside of fitting. Make sure there is no uncoated surface. Avoid puddling of cement, it may weaken the joint.
6. Immediately insert pipe into fitting with twisting motion. Cement should be wet. If it has dried recoat both parts. Use sufficient force to ensure pipe bottoms into fitting.
7. Hold joint together for 30-40 seconds to make sure pipe is not pushed out longer time if temperature is low and for larger pipes.
8. Allow 15 minutes set time before handling the assembly and 2 hours cure time if temperature is below 16 C or 60 F Longer cure time may be required for larger pipe and /or temperature is below 16 C or 60 F.
DIRECTIONS FOR USE:
Shake well before using.
Keep container closed when not in use.
Set time is the time required before joint can safely be handled.
Cure time is the time required before joint can be pressure tested.
1. Cut pipe square with saw or hand cutter. Remove all burrs.
2. Check dry fit of pipe and fitting. Pipe should easily go way into fitting. If pipe bottoms into fitting
it should be very snug.
3. Pipe and Fitting should be free of dirt, grease and other foreign materials. If necessary clean pipe and
fitting using RPC-WELD Pipe Cleaner. Primer is highly recommended for 3 and larger diameter installation.
Apply liberal coat. Primer will start softening surface of pipe and fitting thus ensuring superior joint.
4. Use applicator supplied with the can or suitable applicator at least the size of the pipe diameter
5. Apply liberal coat of cement to the pipe (equal to depth of fitting) and adequate coat inside of fitting.
Make sure there is no uncoated surface. Avoid puddling of cement, it may weaken the joint.
6. Immediately insert pipe into fitting with twisting motion. Cement should be wet. If it has dried recoat both parts.
Use sufficient force to ensure pipe bottoms into fitting.
7. Hold joint together for 30-40 seconds to make sure pipe is not pushed out longer time if temperature is low
and for larger pipes.
8. Allow 15 minutes set time before handling the assembly and 2 hours cure time if temperature is below 16 C or
60 F Longer cure time may be required for larger pipe and /or temperature is below 16 C or 6
RPC-WELD PVC solvent cements have passed the following tests performed according to ASTM Standard D2564
Test Pressure
2 hour Hydrostatic Burst Test 400 psi
2 Hour Lap Shear Test 250 psi
16 Hour Lap Shear Test 500 psi
72 Hour Lap Shear Test 900 psi
DIRECTIONS:
Keep container close when not in use
Set time is the time required before joint can safely be handled.
Cure time is the time required before joint can be pressure tested
1. Cut pipe square with saw or hand cutter. Remove all burrs.
2. Check dry fit of pipe and fitting. Pipe should easily go to way into fitting. If pipe bottoms into fitting
it should be very snug.
3. Pipe and Fitting should be free of dirt, grease and other foreign materials. If necessary clean pipe and
fitting using RPC-WELD Pipe Cleaner. Primer is highly recommended for 3 and larger diameter installation.
Apply liberal coat. Primer will start softening surface of pipe and fitting thus ensuring superior joint.
4. Use applicator supplied with the can or suitable applicator at least the size of the pipe diameter
5. Apply liberal coat of cement to the pipe (equal to depth of fitting) and adequate coat inside of fitting.
Make sure there is no uncoated surface. Avoid puddling of cement, it may weaken the joint.
6. Immediately insert pipe into fitting with twisting motion. Cement should be wet. If it has dried recoat both parts.
Use sufficient force to ensure pipe bottoms into fitting.
7. Hold joint together for 30-40 seconds to make sure pipe is not pushed out longer time if temperature is low
and for larger pipes.
8. Allow 15 minutes set time before handling the assembly and 2 hours cure time if temperature is below 60 F.
Longer cure time may be required for larger pipe and /or if temperature is below 60 F.
Do not test with compressed air.
DESCRIPTION:
RPC-WELD Pipe Cleaner is a special blend of solvents formulated to clean PVC, UPVC, CPVC, ABS and Styrene Pipes & Fittings, all schedules and all diameters, prior to applying cement. This Pipe Cleaner will effectively remove oils, dirt, grease and other foreign matter from the surface of pipe and inside of fitting. It is very important that the surface of pipe and inside of fitting is clean for a strong leak proof joint. This product is made in the India.
APPLICATION:
RPC-WELD Pipe Cleaner may be used on PVC, UPVC, CPVC, ABS and Styrene. Use applicator supplied with can or suitable applicator 1/2 the size of pipe being joined.
PROPERTIES AND SPECIFICATIONS:
Color: Clear
Appearance: Liquid
Shelf Life: 3 years
