Silicone Rubber Foam Pad

Honeywon»s silicone sponge is with high grade silicone rubber material and inimitable technique, with
Good character of high temperature resistant, aging resistant, ozone resistant, insulation property, fuel
Oil resistance, lubes resistance, no smell and wear well. High compressibility and low compression set
Over a wide temperature range, and good acoustic and thermal insulation properties. Apply to -50µ
~+200µ protect and heat insulation for long term continuous use and -70µ ~ +260µ for intermittent
Use on all kinds of machine.

Feature:

Standard size(mm)+ 290*380*¿5-15) 380*380*(5-15) 400*600*(5- 15) 500*500*(2-30)
500*600*(5-15) 600*800*(5-15) 1000*1000*(5-12) 1000*1200*(5-12)

Special size(mm)+minimum length:no limitation maximum length:no limitation, or in roll
Minimum width:no limitation maximum width:1200 minimum thickness:3.0 maximum
Thickness:30.0

Product color+ red¼grey¼natural, white¼black or any other required color

Application+ heat transfer print equipment, electronics and electrics, machine and sealcharacter+high temperature resistant, aging resistant, ozone resistant, insulation property, fuel oil
Resistance, lubes resistance, no smell and wear well, good acoustic and thermal insulation properties.


+ technical index¦
Style¦ open cell
Surface¦double fabric impression
Tear strength¦55kn/m
Press strength+30mpa
Elongation¦100%
Hardness¦8-50 shore a
Temperature range¦-50-220c continuously; -70µ ~ +260µ for intermittent use
Density¦0.55-0.9g/cm3
Flame resistance¦94v-0
Dielectric breakdown voltage¦>3kv
Dielectric constant¦5.5 khz
Tensile strength: 10-30psi
Volume resistance¦1.*1011 ohm-m
Thermal conductivity¦0.1 w/m-k
Thick tolerance: a0.05mm~0.1mm

INTRODUCTION:
Silicone Foams is a soft, two-component platinum silicone flexible foam that is versatile and easy to use. Vibrant colors can be achieved by adding color pigments. Cured foam is high heat resistance (will resist up to 350°F/176°C), water resistant, UV resistant and resists oxidation and ozone degradation.

FEATURE:
1.Mixed Viscocity
2.Very soft
3.Excellent temperature resistence


IMPROVE SURFACE FINISH AND MINIMIZE VOIDS WITH BACK PRESSURE:
Use a board that will completely cover the mold opening. Using a drill bit, drill 3 holes in the board spaced a few inches / cm apart. Make sure that, when the board is placed over the mold opening, the holes are over the mold cavity and rising foam will be able to make it through. Apply Ease Release 200 thoroughly too both sides of the board and into the drilled holes. Mix and pour foam into mold cavity and place board over mold opening. Hold board firmly in place. As foam rises in the mold cavity, some foam will grow out of the drilled holes. After the foam stops growing, you can let go of the board. Do not demold for at least 20 minutes.

APPLICATION:
Silicone Foams can be used for a variety of industrial and special effects applications including making foam filled appliances, padding/seat cushioning, orthotics/orthopedics, potting and encapsulation of electrical circuits and vibration dampening.


ABOUT US:
We are engaged in silicone rubber's R&D since 1996,there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber.

What's more,our silicone rubber are environmental-friendly production,with high safety and no toxic.You can absolutely trust your choice with us.

For more information, welcome to contact Lilian:
Wechat / Phone: 8613617490457
E-mail: lilian(at)xrsil(dot)com
Skype: lilian-xrsilicone
Company: Dongguan Xinrun Silicone New Materials Co., Ltd / Xinrun Group Limited
Factory address: No.2,Zhouliao Road, Langzhou Industrial Zone,Changping, Dongguan, Guangdong, China

The pad printing silicon rubber is a carrier which transfers the patterns from the steel plate onto the products' surface.
The pad printing silicon rubber has the advantages of good printing effects,good quality,good resilience and without any impurity.
Pad printing silicon rubber is mainly applicable to the printing of irregular patterns on plastics toys,electronplating products,electronic toys, trademarks,artwork gifts ,stationeries etc.

Applications of liquid pad printing silicone rubber
Pad printing silicone rubber is mainly use for printing irregular patterns of plastic toys, electroplating toys and trade makers . Pad printing silicone rubber as a carrier which transfer patterns on the steel plate to the toys products surface.

2. Features of liquid pad printing silicone rubber
a. resistance to deformation, high-temperature
b. high printing times
c. good aging resistance
d. exceptional elasticity
e. great printing effect

3. Operation Instructions of liquid pad printing silicone rubber
Pad printing silicone rubber is two-component silicone, part A is liquid silicon rubber, part B is catalyst. The usual mixture of silicone rubber and catalyst is 100: 2 or 100: 3. E.g. we take 100g of liquid silicon rubber and 2g-3g catalyst, mix them and pour it to your mold. A fter 2-4 hours, you will get a Pad printing silicone rubber.

HY-918 with the advantages of high temperature resistance, abrasion resistance,  good printing effect, etc. , which made of top-quality raw material due to adding American Dupont Teflon high-temperature resistance new material, is processed through high-temperature machining. The product is mainly applicable to plastics toys, electroplating products, electronic toys, trademarks and irregular pattern printing. The silicon pad is a carrier which transfer printing the patterns on the steel plate onto the toy products' surface.

HY-918 is a kind of silicone rubber to make the printing pads for plastic toys, craft works, product printing.

Characteristics
good printing effects
good quality
good resilience
and without any impurity.

Silicone rubber for pad printing features description
Pad printing silicone rubber with highprint times and abrasion resistance, without any impurities, with good printingeffects, permanent and durable, we can provide all kinds of colors and ourcatalyst is free charged.
Applications：
The pad printing silicone rubber is mainly use for printing irregular patterns of plastic toys, electroplating toys, trade makers .Silicone pad printing is a carrier which transfer printing the patterns on the steel plate onto the toys products surface.

Silicone rubber for pad printing instructions
Pad printing silicone rubber istwo-component silicone, part a is the liquid silicone rubber, part b is thecatalyst. The usual mixing ratio for silicone rubber and catalyst is100 : 2-3, eg. We take 100grams of liquid silicone rubber, then weadd 2-3 grams catalyst, mix then evenly and pour it to your mold.Then after 2-4 hours, you will obtain a printing pad.
Features
1.Non-exothermic
2.Mold-releasability
3.Dimensional stability
4.Excellent flowability
5.Heat & chemical resistance


25kgs/drum vacuum package or 200kgs/drum

Pad printing silicone rubber is rtv2 silicone, also called two components silicone or two parts silicone, part A and B will vulcanize in room temperature when A and B mixed.
The mix ratio of tin cure silicone is 100:3, the platinum cure silicone is 9:1.

Description of Liquid Silicone Rubber for Pad Printing
Liquid Silicone Rubber for Pad Printing Mainly used for making plastic toys, electroplating products, electronic toys, trademarks, communications equipment, gifts, stationery and other irregular pattern. Pad printing is the pattern on the plate carrier made by plastic head, then transfer the pattern on the plate on the toy products, Pad printing silica gel demand quality exquisite, no impurities, rebounwell, apply oil well, a clear printing pattern

Feature of liquid silicone rubber for pad printing
1, Oil fell oil effect is good
2, Exquisite, good resilience, printing more often, no impurities, no particles
3, Printing clear pattern
4, Low viscosity, good fluidity
5, No shrinkage, easy apply oiling , clear printing pattern

Precautions of liquid silicone rubber for pad printing
No mixing with acid-base materials, alkoxy silane or high temperature water vapor, otherwise there is the
tendency of curing and viscosity changes.
[ Sample ]
We can send 1kg sample for free ,but the shipment charge usually paid by your side
[ Rapid response to your needs ]
We will be answer within 24hours.
Welcome to contact with us if you have any problems.

High Quality Transparent Molded Silicone Rubber for Kitchen Ware and all kinds of molded silicone products.


Description
GFD2071P series is fume type general purpose silicone rubber with shore A hardness 30,40,50,60,70,and 80.These products are suitable for compression molding and extruding.

Features
Excellent process ability
Excellent mechanical and electrical properties
High tensile strength
FDA & FLGB grade

Applications
Kitchenware, bakeware
Skin cover for mobile devices
Tubes, sealing

Product Data
Item Standard (GB/T) 2031P 2041P 2051P 2061P 2071P 2075P 2081P
Appearance Transparent
Linear shrinkage
(%) 130mm 130mm 3.6 3.6 3.5 3.5 3.4 3.3 3.3
Hardness
(Shore A) 531.1-2008 31 42 51 62 71 75 81
Tensile strength (MPa) 528-2009 8.2 10.2 10.4 10.1 10.0 9.7 9.0
Elongation
(%) 528-2009 759 652 570 462 369 310 205
Tensile set
(%) 528-2009 6.0 3.6 4.0 5.6 5.2 3.6 2.8
Tear strength
(KN/m) 529-2008 24 28 32 32 31 28 26
Curing agent: C-15, 2%; Curing condition: 170 ºC 10mins, Post cure: 200 ºC 4 hours

Storage:
Store in a cool and dry place, out of direct sunlight
Package: 20Kg/carton or 600Kg/box

Introduction of rtv 2 molding silicone rubber:
1. Two-part of rtv 2 molding silicone rubber: flowable liquid silicon and catalyst.
2. Rtv 2 molding silicone rubber cures at room temperature within 4-6 hours.
Features of rtv 2 molding silicone rubber:
1. Rtv 2 molding siliconerubber has an exceptional fluidity and good operability.
2. Rtv 2 molding silicone rubber hasgood temperature and deformation resistance as well as low shrinkage.
3. Rtv 2 molding siliconerubber has high duplication times.

Operation step for rtv 2 molding silicone rubber:
1. Step one to use rtv 2molding silicone rubber: take 100g of part a and add 2g of part b and mix thesilicon rubber and the curing agent evenly.
2. Step two to use rtv 2molding silicone rubber: vacuum pumping
3. Without exception, thistakes less than 10 minutes. Otherwise, it will cause cross linking reaction, and no more further steps will be available.
4. Step three to use rtv 2molding silicone rubber: brushing cast & perfusion molding operation.


25kgs/drum vacuum package or 200kgs/drum