DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Turnkey dustless automatic plastic painting line:
1.Plastic spray painting line
2.Plastic painting line
3.Automatic painting line
4.Plastic painting line
5.Dustless painting line
5. Plc control panel
6 .Air handling unit for fresh air to oven, spray booth, dedusting booth and complete paint shop area.
7. Thermal coat / sandwich panel for the plant
8. 1.2mm-1.5mm-2.0mm ss sheet
9. Used for various plastic parts, automobile parts, injection moulded plastic parts
--Wall panel: sandwich style, δ=50mm, polystyrene .rock wool is optional.
--Door: 3 pcs of front door without aluminum side cover.
1pcs of emergency door with pressure lock.
--Exhaust fan: 1 unit of 5.5kw unilatcral centrifugal fan.
--Exhaust duct: 3m straight ducts, one 90° bend, and one 60° bend.
--Filtration: mounted at the rear wall panel.
--Roof filter: 2 pcs of filter, mounted above support frame,
which is made of steel and powder coated.
--Upper light: 8 sets, 4*40w per set.
--Control box: components made in china, overload, overheat,
phase-lacking protection, straight driven motor.
--Omni- directional movable infrared light as optional.
Technical Specifications
External size(m) 8.1x4.0x3.2
Internal size(m) 6.9x3.9x2.7
Door width (m) 3.0
Door height (m) 2.66
Air flow (m3/h) 18000
Inside on-load air speed(m/s) 0.25-0.3
Power (kw) 7
Vehicle suited Saloon car
GuangLi Spray Booth
--Wall panel: sandwich style, δ=50mm, polystyrene. rock wool available as required.
--Basement: steel structure, 3 rows of vein board and 2 rows of grids, full grids as optional.
--Door: 3 pcs of front door without aluminum side cover. 1pcs of emergency door with pressure lock.
--Ramp: 2 pcs of vein board.--One 7.5kw intake fan and one 5.5kw exhaust fan.
--4m straight exhaust ducts, one 90° bend, and one 60° bend.5m straight chimney and 2 small bends.
--Spraying/baking transition damper, automatically air controlled.
--Heat exchanger: stainless steel. Riello G20 burner.
--Roof filter: 4 pcs of filter, mounted above support frame,which is made of steel and powder coated.
--2 pcs of floor filter and 1 pcs of outlet filter.--Upper light: 10 sets, 4*40w per set. side lights: 8sets,2*40w.
--Control box: components is import, overload, overheat, phase-lacking protection, straight driven motor.
--Automatically stop when preset time is up.Constant temperature spraying.
--Environmental filter: the equipment can be adopted M style activated
carbon or drawer style activated carbon as optional.
Technical Specifications
External size(m) 7.0x5.3x3.5
Internal size(m) 6.9x3.9x2.7
Door width (m) 3.0
Door height (m) 2.66
Air flow (m3/h) 24000
Inside on-load air speed(m/s) 0.3-0.35
Power (kw) 16
Vehicle suited Saloon car
