Asg Joint Compound

APPLICATION OF SK-HB K-SILICATE MORTAR :

* K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors.
It is also used for jointing chemical resisting stoneware pipes.
K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles.
The concrete surface needed protection should be dryed, clean and rough.
The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner.

When Bedding and Jointing Materials are the same.
On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints.
The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water.
Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic.
When Bedding and Jointing Materials are Different.
Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR
A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions.

PREPARATIONS OF MORTAR :
* Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan.

* Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar.

* In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared.

* The cement mortar will be used before it starts setting.

Brighto Gypsum Joint Compound

Price :
3.60 Ltr -USD 3.5
18 Ltr- USD 13.1

Gyp-Filler is a specialist powder product manufactured from gypsum and other active ingredients. The special formula provides good levels of adhesion to the plasterboard surface, high flexural strength and coexisting matching properties of the filler and plasterboard

Key facts
No cracking due to coexisting materials
Good adhesion on the plasterboard surface
High flexural strength
Suitable for all kinds of jointing tapes on the market
Application
In addition to Gyp-Filler as a jointing system for drywall and concealed ceiling systems,
Gyproc - Vinh Tuong suggests also using Vinh Tuong paper tape for optimal performance.

Manufacturing Standards
EN 13963

Compose A Joint Usg Boral - Ready Mix Joint Compound All Purpose

Joint Compound Is Usually Sold Pre-mixed. This Product Is Used For Almost Every Drywall Installation And Repair. Joint Compound Is Used To Finish Drywall Joints And Corners. It Provides Faster And Superior Performance In Joint Closure. It Is Also Useful For Repairing Cracks And Holes In Existing Plasterboard And Plaster Surfaces. You Can Save Time By Using Joint Compound Cause It Does Not Need To Any Extra Process. It Is Ready To Use. It Takes 6 To 12 Hours To Dry, Depending On The Humidity And Temperature.

Turkey Is One Of The World's Leading Country In The Gypsum Resources And Production Of Gypsum. As Board And Wall Company; We Export Highest Quality Of Gypsum Powder And Joint Compound All Around The World.

Megaturk Co. Ltd, Istanbul - Turkey

Cemstar" Cement Board Jointing Compound
Jointing Compound for Fiber Cement Boards
Exterior grade
2 part (15kg compound & 5 KG Resin)
20 kg plastic pails
MOQ - 4 pallets
168 pails

Jointing Compound for Fiber Cement Boards
Interior grade
premixed compound
25 kg plastic pails
MOQ - 4 pallets - 168 pails

MOQ : FCL 20ft
Shipping : Sea Freight