Bumper Die

Cold Shot Nitrogen Deburring Machine Introduction

Automatic deburring is a process for removing flash from molded rubber parts. We use liquid nitrogen, high - speed rotation and shot blasted plastic media in varying combinations to remove the flash in a highly precise, economical and expedient manner. Parts that have thin flash can be quickly and thoroughly cryogenically deflashed. This process is exceptionally good at removing the inner dimensional and complex flash that cannot be removed by any other method.

Application

O - rings, gaskets and other rubber sealings
Insulators and other electric / electronic components
Valve stems, washers and fittings
Short tubes and flexible boots
Rubber absorbers and bumpers for automobile
Face masks & goggles
Mobile phone housing and intelligent watch strap
Zinc and mag alloys like door lockers for auto cars

SPECIFICATIONS

NS - 120C
Size: L1400mm * W1300mm * H2300mm
Weight: 1500kg
Power Supply: AC380V 50HZ
Electrical Capacity: 8KW * 3PH
Design Temp: - 130Deg. C
Design Pressure: 0.5 - 0.7 Mpa
Outer Wall Material: SUS
Frame Material: 100% SUS304
Barrel Capacity: 120L
Wheel Speed: 6, 000 rpm Max
Barrel Speed: 0 - 16rpm
Media Throw wheel Size : 350
Operation Mode: Press Button

Automatic Deburring Machine Introduction

Automatic deburring is a process for removing flash from molded rubber parts. We use liquid nitrogen, high - speed rotation and shot blasted plastic media in varying combinations to remove the flash in a highly precise, economical and expedient manner. Parts that have thin flash can be quickly and thoroughly cryogenically deflashed. This process is exceptionally good at removing the inner dimensional and complex flash that cannot be removed by any other method.

Application

O - rings, gaskets and other rubber sealings
Insulators and other electric / electronic components
Valve stems, washers and fittings
Short tubes and flexible boots
Rubber absorbers and bumpers for automobile
Face masks & goggles
Mobile phone housing and intelligent watch strap
Zinc and mag alloys like door lockers for auto cars

SPECIFICATIONS

NS - 60C
Size: L1160mm * W1100mm * H2155mm
Weight: 800kg
Power Supply: AC380V 50HZ
Electrical Capacity: 5KW * 3PH
Design Temp: - 130Deg. C
Design Pressure: 0.5 - 0.7 Mpa
Outer Wall Material: SUS
Frame Material: 100% SUS304
Barrel Capacity: 60L
Wheel Speed: 7,200 rpm Max
Barrel Speed: 0 - 26rpm
Media Throw wheel Size : 250
Operation Mode: Press Button

Helmet mould

Automotive parts mould

Mud guard mould
Fan shroud mould
Bumper mould
Grille mould
Lamp mould

Auto parts car front bumper mold plastic injection mold
A car bumper is a safety device that absorbs and mitigates external impact and protects the front and rear of the vehicle body. Generally consists of plastic bumpers, cushioning materials and beams. Plastic bumpers have strength, rigidity, and decorativeness. From a safety point of view, a car can play a cushioning role in the event of a collision and protect the front and rear body. From the appearance, it can be naturally combined with the car body to form a natural One body, with good decoration, has become an important part to decorate the appearance of the car.
1: Determination of bumper shell material
Regulatory requirements: The front and rear protection devices of the car must ensure that the vehicle will not cause serious damage to the vehicle when a light collision of 4km / h occurs. In addition, the front and rear bumpers not only protect the vehicle and reduce vehicle damage, but also protect pedestrians and reduce the injuries to pedestrians in the event of a collision. Therefore, the shell material of the bumper should have the following characteristics:
1) With less surface hardness, it can reduce pedestrian injuries;
2) Good elasticity and strong resistance to plastic deformation;
3) Good vibration damping effect, can absorb more energy in the elastic range;
4) Resistant to humidity and dirt;
5) Has good acid and alkali resistance and thermal stability.
Modern car bumper shells are mostly made of plastic or fiberglass. In order to reduce the cost of trial production, save mold production costs, and also shorten the trial production cycle, in the concept car trial production, consider using FRP glass fiber reinforced epoxy hand lay-up process.
The materials of the bumper are generally PP + EPEM + T20 or PP + EPDM + T15. EPDM + EPP is also more versatile. ABS uses less and is more expensive than PP. The thickness of the bumper is usually 2.5-3.5mm, and the gas-assisted molding can be made thinner.
Note that if the bottom mesh of the bumper is integrated with the bumper, the thickness of the mesh must be more than 2.0mm, and the die angle should be increased as much as possible (2 degrees or more). If the mesh is separate, the mesh wall of 1-1.5mm is sufficient.

automotive injection mold-Automotive bumper mould- Dalian Mintadely mould Co., Ltd. was established in Dalian in 2006, Mainly engaged in the design and manufacture of plastic mold China, injection mold China, China mould, automobile parts mold of semiconductor, IC connector, lead frame electrical connection and motor fixed rotor, as well as various precision mold spare parts and spare parts. We guarantee to provide customers with excellent design and first-class quality products at any time and occasion.

ISO 9001:2008 Certified
Your Trusted Plastic Molds, Injection mold, Die Parts, Die Casting mold Partner in China. We are not only make molds and parts for you, but also your technical supporting team.
Who using our mould: Meredes-Benz, BMW, Audi, Honda, Toyota, Volkswagen, Nissan, Mazda,etc.

We have design department, laboratory and testing center and a R&D team with a strong technical and experienced to ensure continuous improvement and innovation of processes and products to meet the different needs of different customers.

Apply ERP system, implement standard management in process, quality, delivery, product, service. Ensure customer's product quality and delivery time.


With many years of experience in mold design, manufacture, molding, leading technical solutions and perfect quality service, we can keep our eyes on the global market while consolidating existing customers.

Grille mold-Bumper mold-Car key mold - Dalian Mintadely mould Co., Ltd. was established in Dalian in 2006, Mainly engaged in the design and manufacture of plastic mold China, injection mold China, China mould, automobile parts mold of semiconductor, IC connector, lead frame electrical connection and motor fixed rotor, as well as various precision mold spare parts and spare parts. We guarantee to provide customers with excellent design and first-class quality products at any time and occasion.

ISO 9001:2008 Certified
Your Trusted Plastic Molds, Injection mold, Die Parts, Die Casting mold Partner in China. We are not only make molds and parts for you, but also your technical supporting team.
Who using our mould: Meredes-Benz, BMW, Audi, Honda, Toyota, Volkswagen, Nissan, Mazda,etc.

We have design department, laboratory and testing center and a R&D team with a strong technical and experienced to ensure continuous improvement and innovation of processes and products to meet the different needs of different customers.

Apply ERP s ystem, implement standard management in process, quality, delivery, product, service. Ensure customer's product quality and delivery time.


With many years of experience in mold design, manufacture, molding, leading technical solutions and perfect quality service, we can keep our eyes on the global market while consolidating existing customers.