Uv-Resistant Thermoplastic Vulcanizate

V4 Borewell Submersible Pumpset
Falcon Premium 100 mm (4) Borewell Submersible pump is firmly coupled to a submersible electric motor and Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosive resistance thermoplastic and the shaft is of SS 410.

Pump Liquids
- Clean
- Thin
- Non-Aggressive
- Non-Explosive
- Clear
- Cold
- Fresh water
- Without abrasives
- Solid particles.

Salient Features
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Specially designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect alignment and
Thereby increases the life of the pump set
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps.

Specification
Power Range : 0.37 kW to 4.4 kW (0.50 HP to 6.0 HP)
- Version : Single Phase 160V to 230V, Three Phase 350 to 415V, 50Hz AC Supply.
Single Phase available in 0.5 HP to 5.0 HP
Three Phase available in 1.0 HP to 6.0 HP
- Speed : 2880 RPM
- Head Range : 10 Mtr. To 340 Mtr.
- Discharge Range : 450 LPM to 12 LPM
- Outlet Size in Inch : 1.0 , 1.25, 1.5 & 2.0
- Degree of Protection : IP 58
- Direction of Rotation Minimum Cooling : Counter clockwise from driving end -1ph: Electrically Reversible -3ph
- Thrust Load : 0.37 kW â?? 0.75 kW- 650 lbs, 1.1 kW -1.5 kW -1000 lbs,
2.2kW, 7.5 kW -1500 lbs.
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR): 3ph
Direct Online (D.O.L)
- Maximum Starts Per Hour : 20 Times

V3 Borewell Submersible Pumpset

Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410.

Pump Liquids
- Clean
- Thin
- Non-Aggressive
- Non-Explosive
- Clear
- Cold
- Fresh water
- Without abrasives
- Solid particles.

Salient Features
- Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell
- More durability and hygiene
- High operating efficiency
- Specially designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps.

Specification
- Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP)
- Version : Single Phase 160V to 230V, 50Hz, AC Supply
- Speed : 2880 RPM
- Head Range : 14 Mtr. to 96 Mtr.
- Discharge Range : 70 LPM to 15 LPM
- Outlet Size in Inch : 1.25"
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor
- Maximum Starts Per Hour : 20 Times

Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m�²/sec (max.)
- Ph Value : 6.5 to 8.5

V3 Borewell Submersible Pumpset
Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410.

Pump Liquids
- Clean
- Thin
- Non-Aggressive
- Non-Explosive
- Clear
- Cold
- Fresh water
- Without abrasives
- Solid particles.

Salient Features
- Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell
- More durability and hygiene
- High operating efficiency
- Specially designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps.

Specification
- Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP)
- Version : Single Phase 160V to 230V, 50Hz, AC Supply
- Speed : 2880 RPM
- Head Range : 14 Mtr. to 96 Mtr.
- Discharge Range : 70 LPM to 15 LPM
- Outlet Size in Inch : 1.25"
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor
- Maximum Starts Per Hour : 20 Times

Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5

Harbour construction
Individual profiles on quay walls

Fenders
Wear plates and slides
Floating docks
Wear plates where dock meets pillage
Bushings for pivots
Fenders
Slide

Please do not hesitate to contact us should you have any questions.


Plastic film and pallets

Made out of PVC material
16mil thickness (0.4mm)
UV resistant
Color: Red, Dark Green, Orange, etc
Regular size: 6ft x 6ft & 8ft x 6ft
This curtain is used to barricade the area where welding is carried.
We can customize the size of blanket as per client requirements

8ft x6ft

Ultraviolet Irradiation Crosslinking Equipment
Application of UV-light irradiation cross-linked equipment
The UV-light irradiation cross-linking process uses UV-light as the irradiation source, extrudes and coats the mixed photo-crosslinking polyolefin compound on the conductor wire core, and then immediately enters the special irradiation equipment for fused photo-crosslinking. The insulated wire core after light irradiation cross-linking can be produced into photo-crosslinking polyolefin insulated wire and cable products through cooling treatment at different temperatures and other subsequent processing.
UV-light irradiation cross-linking method needs to be slightly modified only on the original normal extrusion production line. The upper traction, irradiation box and electric control cabinet with a small floor area can meet the operating requirements and produce UV-light irradiation cross-linked polyethylene wire and cable products. The addition of upper traction enables the conductor wire core to maintain a certain tension. In the running process, it shall be always in the center of irradiation box to ensure the best irradiation effect. The irradiation box uses a reflective focused UV light source that is uniformly configured and specially designed, and the electrical control system will ensure that the UV-light intensity and the irradiation temperature in the center of the irradiation box are in the optimum operating conditions. In addition, the efficient photo-initiation system rapidly induces cross-linking reaction of polyolefin under the UV-light irradiation, so that the irradiation equipment can reach a continuous production speed of dozens of meters per minute, and gradually cools at hot, warm and cold temperatures to ensure the stability of three-dimensional cross-linked netlike structure.

5KV Power frequency high-voltage test console
Wire and Cable Detection Equipment
Power Frequency High Voltage Test Console
The power frequency high-voltage test console is designed for finished low-voltage cables, which is composed of the console, a 50KVA induction regulator and an experimental transformer. It has a standard capacity of 50KVA and a voltage of 5KV. The low-voltage cable can generally withstand the voltage of 3.5KV, and the equipment can withstand the voltage of 5KV. The equipment is operated by electric control. In addition, high voltage will automatically return to zero in case of cable break and give a sound-light alarm and leakage protection, so as to protect the safety of the operator and the staff to the most extent.
Main technical parameters of the system:
Rate capacity   50kVA/ 100KVA/ 150KVA/ 200KVA
Rated input voltage  380V
        Rated output voltage  0-5KV/ 0-10KV/ 0-15KV/ 0-20KV/0-25KV
Main technical indicators:
1. It will automatically give an alarm (sound-light) and delay in cutting off high voltage (adjustable from 0.1-1S) in case of test piece breakdown.
2. Zero potential of voltage regulator is started under high voltage.
3. The voltage regulator automatically returns to zero after breakdown, overcurrent protection and non-zero tripping under high voltage.
4. Cut off the power source after the hold-off time is up and voltage automatically returns to zero at the step-up rate.
5. The hold-off time of digital display time relay is adjustable.
6. Measurement accuracy of high-voltage output and current output is +3%.
ã??ã??When low-voltage wires are used in the power frequency withstand voltage test, the equipment with a voltage of 5KV and capacity of 50KVA is usually used.
ã??ã??Voltage capacity may be customized according to customer needs.
We are Cable Detection Equipment Supplier

CP-50 Wire and cable sheet-punching machine
Wire and Cable Detection Equipment
Cable Detection Equipment Supplier
CP-50 type die punching machine is used to punch rubber, plastics, leather and other special materials into test pieces specified in various standards for trial use. In addition, it can also be used as small punch press.

Double Faced Flaker
Wire and Cable Detection Equipment
Cable Detection Equipment Factory
Features and usages:
The machine is widely used in rubber, plastics, leather, wire and cable industries and scientific research units, and is indispensable for the preparation of test pieces. It can be used to cut various test pieces with a Shore hardness above 40 degrees and a thickness of 1-12 mm. The sheet material it cuts has a smooth and flat surface; the dimensional tolerance of thickness can be controlled within ±0.2; it can be used to directly cut the test piece without need for grinding.

II. Technical parameters:
1. Table width: 300mm
2. Slice thickness: 1-12mm
3. Slice width: â?¤100mm
4. Maximum feed thickness: 20mm
5. Motor type: Y100L-8   1.1KW    710r/min     380V
6. Dimensions: LÃ?WÃ?H: 625