Cjy1.5 Ton Mining Trolley Locomotive

14 ton mining trolley locomotive

The locomotive is a new product specially designed for large mines. It applies IGBT speed control way, realizes smooth starting and low failure rate, and is a new- generation energy efficient product. Main features include: small outer diamensions, short wheel base, small turn radius, high speed and strong traction force.
V-shape rubber damps are used on this locomotives in order to bear viration and impact from lengthways, vertical and transverse directons. The sails are elastic rubber plates which can ensure a reduced shock in operation.

Adhesive / total weight (t) : 14 ton
Track gauge (mm) : 600.762.900
Traction (KN) : 26.68
Max. Traction (KN) : 34.3
Speed(km/h) : 12.87
Power (KW) : 52 2
Dimensions Length(mm) : 4800
Width(mm) : 1060,1222or 1360
Height(mm) : 1700
Wheelbase (mm) : 1700
Wheel diameter (mm) : 760
Min Curve radius (m) : 12
Controller : Resistencia or IGBT
Braking method : Mechanical

3 ton trolley wire locomotive for mining

What Should We Pay Attention to When Using Underground Mining Electric Locomotives?
Operating underground mining electric locomotives is a critical task that requires a high level of responsibility and safety awareness. To ensure safe operation, operators should heed the following guidelines:
Monitor Bearing Temperature:
Pay close attention to the temperature of the axle box, motor bearings, and gearbox bearings to prevent overheating and potential damage.
Be aware of any burning smells, as this is a typical sign of overheating bearings.
Regularly check the bearing lubrication oil to ensure it is adequate and meets the required specifications.
Inspect the Brake System:
Regularly inspect the brake shoes for wear and replace or adjust them as necessary.
Ensure the brake system is functioning correctly, and that the braking distance meets specified requirements.
Periodically clean the brake system of dust and grease to maintain its cleanliness and efficiency.
Immediately Address Electrical Equipment Failures:
If any electrical equipment, lights, or horns fail, cease operations immediately and take the locomotive to the garage for repairs.
Do not continue to operate the locomotive with any faults, as this could lead to safety incidents.
Strictly Follow Shift Handover Procedures:
At the end of a shift, operators should conduct a thorough inspection of the locomotive, including:
Checking bearing temperatures, the brake system, and electrical equipment.
Inspecting the locomotive's exterior for any damage.
Listening for any unusual sounds from the locomotive.
Record all inspection results in the shift handover log to inform the incoming operator of the locomotive's condition.
Additional Precautions:
Adhere strictly to the mine's management regulations.
Familiarize yourself with the locomotive's operating procedures and maintenance methods.
Regularly participate in safety training and drills to enhance safety awareness and emergency response capabilities.
By strictly following these precautions, operators can effectively prevent accidents when using underground mining electric locomotives, ensuring their own safety and the safety of others.

Adhesive weight (t) : 3 ton
Track gauge (mm) : 600.762.900
Traction (KN) : 6.1 or 5.74
Max. Traction (KN) : 7.36
Speed(km/h) : 10.6 7.5
Power (KW) : 12KWx1 6.5KWX2
Dimensions Length(mm) : 2700, 2750
Width(mm) : 940,1102 or 1240
Height(mm) : 1550, 1500
Wheelbase (mm) : 816, 850
Wheel diameter (mm) : 650, 850
Min Curve radius (m) : 5.7 6
Controller : Resistencia or IGBT
Braking method : Mechanical

7 ton trolley Xiangtan locomotive for mining

Safety is paramount when operating mining Xiangtan electric locomotives. Here are some essential guidelines to ensure their safe usage:
1. Qualified Personnel: Only trained and certified drivers should operate mining Xiangtan electric locomotives. Proper training reduces the risk of accidents due to operator error and ensures that drivers can respond promptly and effectively in case of emergencies.
2. Pre-Operation Checks: Before using a mining Xiangtan electric locomotive, it's crucial to check that all safety equipment, including signal lights, is functioning correctly. Additionally, ensure that the cargo being transported is securely loaded to prevent any items from falling during transit.
3. Regular Maintenance: Regular maintenance is essential for the safe operation of mining Xiangtan electric locomotives. Any issues with the locomotive should be promptly addressed, whether it's repairing faults or replacing worn components. Regular testing should also be conducted on braking distances and motor insulation to ensure that all performance metrics meet safety standards.
4. Routine Inspections of Infrastructure: Regular inspections of the tunnel environment, including equipment and tracks, are necessary to minimize the risk of accidents involving mining Xiangtan electric locomotives. By identifying and addressing potential hazards early on, the likelihood of accidents can be significantly reduced.
By adhering to these guidelines, operators can ensure the safe and efficient operation of mining Xiangtan electric locomotives, prioritizing the well-being of personnel and the integrity of mining operations.
C: Locomotive for coal mining
J: Trolley electric locomotives
Y: Single-end driver's cab
G: Steel wheel,resistor for speed control
GB: Steel wheel,chopping wave for speed control

Product Description
Adhesive / total weight (t) : 7 ton
Track gauge (mm) : 600,762 or 900
Traction (KN) : 13.05kN/ 15.09kN
Max. Traction (KN) : 17.2kN
Speed(km/h) : 11km/h
Voltage : 250V or 550V
Power (KW) : 21kw 2 or 24 kw 2
Dimensions Length(mm) : 4550mm
Width(mm) : 1050,1212 or 1350mm
Height(mm) : 1550mm
Wheelbase (mm) : 1600 mm
Min Curve radius (m) : 7 m
Wheel diameter (mm) : 680mm
Controller : Resistance or IGBT or AC controller
Braking method : Mechanical or air Brake

3 ton trolley electric locomotive for mining tunnel

What to Inspect Before Operating Underground Mining Locomotives?
Before operating underground mining locomotives, it is crucial to conduct thorough inspections to ensure safety and efficiency.
Start by examining key equipment, including electrical and control systems, to verify integrity and confirm that all components are in proper working order. This includes checking fuse specifications and ensuring tight fastenings to prevent potential malfunctions.
Inspect the tracks ahead for any obstacles that could impede locomotive movement, as clear pathways are essential for safe operations. Additionally, assess the condition of brake pads to ensure effective braking when necessary, and inspect the sandboxes to ensure that the sand meets required specifications for optimal traction.
These series of inspections are vital for minimizing operational risks and ensuring the smooth and safe operation of underground mining locomotives. By diligently conducting these checks, operators can mitigate potential hazards and maintain efficient mining operations.

Adhesive weight (t) : 3 ton
Track gauge (mm) : 600.762.900
Traction (KN) : 6.1 or 5.74
Max. Traction (KN) : 7.36
Speed(km/h) : 10.6 7.5
Power (KW) : 12KWx1 6.5KWX2
Dimensions Length(mm) : 2700, 2750
Width(mm) : 940,1102 or 1240
Height(mm) : 1550, 1500
Wheelbase (mm) : 816, 850
Wheel diameter (mm) : 650, 850
Min Curve radius (m) : 5.7 6
Controller : Resistencia or IGBT
Braking method : Mechanical

7-ton Trolley Xiangtan Electric Locomotive for Iron Mine
Trolley electric locomotive is a kind of rail transportation traction equipment, powered by transformers and overhead lines. Mainly used in mines where there is no risk of explosion. Because of its special power supply mode, the trolley electric locomotive has no limit on the cruising range. Therefore, it is suitable for long-term and long-distance use. There are also many options in terms of speed regulation and braking methods. Speed control methods include resistance speed control, chopping speed control and frequency conversion speed control. Braking methods include pure mechanical braking, hydraulic braking and compressed air braking. In addition, electric braking can also be selected as an auxiliary braking method.
C: Locomotive for coal mining
J: Trolley electric locomotives
Y: Single-end driver's cab
G: Steel wheel,resistor for speed control
GB: Steel wheel,chopping wave for speed control

Product Description
Adhesive / total weight (t) : 7 ton
Track gauge (mm) : 600,762 or 900
Traction (KN) : 13.05kN/ 15.09kN
Max. Traction (KN) : 17.2kN
Speed(km/h) : 11km/h
Voltage : 250V or 550V
Power (KW) : 21kw 2 or 24 kw 2
Dimensions Length(mm) : 4550mm
Width(mm) : 1050,1212 or 1350mm
Height(mm) : 1550mm
Wheelbase (mm) : 1600 mm
Min Curve radius (m) : 7 m
Wheel diameter (mm) : 680mm
Controller : Resistance or IGBT or AC controller
Braking method : Mechanical or air Brake

10 ton Trolley Locomotive for Metal Mine
The model has two kinds of working rated voltage:250v and 550V. It applies primary driving way, speed control of IGBT chopping wave type or resistor type or VF type. Main fetures include:short wheel base, high stiffness of vehicle body, and good shockproof performance. The braking type is mechanical or electric braking. Both mechanical braking and electric brking have safe and reliable effect.
Adhesive / total weight (t) : 10 ton
Track gauge (mm) : 600.762.900
Traction (KN) : 13.05 18.93
Max. Traction (KN) : 24.5
Speed(km/h) : 11, 10.5
Power (KW) : 21*2 30*2 24*2
Dimensions
Length(mm) : 4550, 4650
Width(mm) : 1050,1212or 1350
Height(mm) : 1600
Wheelbase (mm) : 1100
Wheel diameter (mm) : 680
Min Curve radius (m) : 7,10
Controller : Resistencia or IGBT
Braking method : Mechanical

10 ton Trolley Locomotive for Metal Mine
The model has two kinds of working rated voltage:250v and 550V. It applies primary driving way, speed control of IGBT chopping wave type or resistor type or VF type. Main fetures include:short wheel base, high stiffness of vehicle body, and good shockproof performance. The braking type is mechanical or electric braking. Both mechanical braking and electric brking have safe and reliable effect.
Adhesive / total weight (t) : 10 ton
Track gauge (mm) : 600.762.900
Traction (KN) : 13.05 18.93
Max. Traction (KN) : 24.5
Speed(km/h) : 11, 10.5
Power (KW) : 21*2 30*2 24*2
Dimensions
Length(mm) : 4550, 4650
Width(mm) : 1050,1212or 1350
Height(mm) : 1600
Wheelbase (mm) : 1100
Wheel diameter (mm) : 680
Min Curve radius (m) : 7,10
Controller : Resistencia or IGBT
Braking method : Mechanical

7-ton Trolley Electric Locomotive for Mining Tunnel
Trolley electric locomotive is a kind of rail transportation traction equipment, powered by transformers and overhead lines. Mainly used in mines where there is no risk of explosion. Because of its special power supply mode, the trolley electric locomotive has no limit on the cruising range. Therefore, it is suitable for long-term and long-distance use. There are also many options in terms of speed regulation and braking methods. Speed control methods include resistance speed control, chopping speed control and frequency conversion speed control. Braking methods include pure mechanical braking, hydraulic braking and compressed air braking. In addition, electric braking can also be selected as an auxiliary braking method.
C: Locomotive for coal mining
J: Trolley electric locomotives
Y: Single-end driver's cab
G: Steel wheel,resistor for speed control
GB: Steel wheel,chopping wave for speed control

Product Description
Adhesive / total weight (t) : 7 ton
Track gauge (mm) : 600,762 or 900
Traction (KN) : 13.05kN/ 15.09kN
Max. Traction (KN) : 17.2kN
Speed(km/h) : 11km/h
Voltage : 250V or 550V
Power (KW) : 21kw 2 or 24 kw 2
Dimensions Length(mm) : 4550mm
Width(mm) : 1050,1212 or 1350mm
Height(mm) : 1550mm
Wheelbase (mm) : 1600 mm
Min Curve radius (m) : 7 m
Wheel diameter (mm) : 680mm
Controller : Resistance or IGBT or AC controller
Braking method : Mechanical or air Brake

Underground 3-Ton Trolley Electric Locomotive for Mining Tunnel
What are the requirements for the track of the mining trolley locomotive
The working principle of the mining trolley locomotive is that after the current is rectified by the rectifier cabinet, it enters the mining trolley locomotive through the overhead line and pantograph. It then flows through various equipment and finally flows from the track back to the substation. Obviously, apart from the mine trolley itself, the tracks, overhead lines and pantographs are all very important. This article makes a brief introduction to the requirements of the track:
1. Each section of the same rail should be connected by a wire or a rail seam welding process to ensure the smooth flow of the circuit.
2. The track is divided into a return track and a non-return track, and the insulation between the two should be done. The first insulating point is placed at the intersection of two kinds of tracks, and the second insulating point is placed on the non-returning track, and the distance between the two insulating points must be greater than the length of a whole train of mine cars. The insulation point needs frequent maintenance to ensure its insulation performance.
3. When there are conductive objects such as wire ropes across the rails, make sure that the two are not in direct contact.
4. Every 50 meters between two parallel rails on the same track, there should be a copper wire with a cross-section of more than 50 square millimeters or a wire with equivalent resistance to connect the two rails.
The above is a brief introduction to the requirements for the mining trolley locomotive track.
Adhesive weight (t) : 3 ton
Track gauge (mm) : 600.762.900
Traction (KN) : 6.1 or 5.74
Max. Traction (KN) : 7.36
Speed(km/h) : 10.6 7.5
Power (KW) : 12KWx1 6.5KWX2
Dimensions Length(mm) : 2700, 2750
Width(mm) : 940,1102 or 1240
Height(mm) : 1550, 1500
Wheelbase (mm) : 816, 850
Wheel diameter (mm) : 650, 850
Min Curve radius (m) : 5.7 6
Controller : Resistencia or IGBT
Braking method : Mechanical