Mitsubishi Canter Tank

Mitsubishi MG400 Motor Grader Specifications
Main Specifications
Blade Width: 3710mm (standard blade width)
Steering System: ATC
Weight & Loads
Operating Weight: 13,100kg
Front Axle Load: 3,700kg
Rear Axle Load: 9,400kg
Dimensions
Overall Length: 8490mm
Overall Width: 2400mm
Overall Height: 3360mm
Wheelbase: 5910mm
Tandem Wheelbase: 1520mm
Ground Clearance: 355mm
Engine
Manufacturer: MTB
Model: 6D22C
Rated Output: 110.3kW (150 PS) @ 2000rpm
Cylinders: 6
Bore x Stroke: 130 x 140mm
Displacement: 11.2liters
Hydraulic System
Output Pressure: 17.2MPa
Oil Flow Rate: 128L/min
Transmission
Type: DPS
Speeds: 6 forward / 6 reverse
Max Travel Speed: 45.0km/h (forward), 45.4km/h (reverse)
Tires
Front: 13.00-24, 14-ply
Rear: 13.00-24, 14-ply
Performance & Other Features
Operation Type: Hydraulic (HYD)
Scarifying Width: 1225mm
Minimum Turning Radius: 6900mm
Articulate Angle: 25
Fuel Tank Capacity: 230L
Optional Equipment: BL(4000), S/C

The precision is extremely high so it can guarantee group angle quality.
The servo controlling machines, servo motor, person-machine touching the contact surface are adopt the original imported installation of japanese mitsubishi system, and the increase assistance brake system. It is stable and efficiency.



Overall dimension 5000 p - 2000 p - 2600 p
Weight g 3000 v
Air pressure g 0.5 x 0.8 mpa
Oil tank capacity
Air consumption g0.45l/min

rolling door making machine
Shutter door making machine
roller shutter door roll forming machine, automatic rolling door making machine
Product Applicationï¼?
This Iron Steel Rolling Shutter Door Slats Roll Forming Machine Prices line uses galvanized steel sheet, colored armor plate or aluminum plate as the material plate. The products produced by this  Iron Steel Rolling Shutter Door Slats Roll Forming Machine Prices are bright in colored, against fading, resistant to rust, and be widely used in shops, working departments, warehouses, and fire partition. Its strength is three times higher than aluminum alloy door.
Technological processï¼?
Uncoiler-Feeding-Leveling-hydraulic punching-Hydraulic cutting-Roll forming-Output table
Technical parameterï¼?
1.Suitable material Color steel sheet , galvanized steel sheet,aluminum sheet
2.Installation Dimension (L*W*H):       6.5m*1.5m*1.4m
3.Main motor power 4KW with Cycloidal reducer
4.Hydraulic station power 4KW
5. Hydraulic oil pump CB-E 310
6.Thickness of material 0.3mm~1.0mm
7.Diameter of principal axis Φ70-90mm
8.Material expand width 1000-1250mm
9.Electric tension 380V 3phase 50HZ or as the customer's requirements
10.Material of roller High grade 45# forged steel plated with hard chrome plating
11.Controlling system PLC
12.Processing speed  8-12m/min(glazed tile is 2-3m/min)
13.Processing precision within 1.00mm (depend on design)
14.Material of cutting blade Cr12 mould steel with quenched treatment 
15.Kind of drive 0.6 inch chain link bearing model 6210
16.Roller station 11-20 Rollers
17.Roller material high grade 45#steel; Cr12 quenching
18. Leak frame load-bearing 4.6T 
Rollers
In order to get high quality product, our machine adopts welded steel frame structure, AC frequency conversion motor reducer drive, chain transmission, roller surfaces polishing, hard plating, heat treatment and chrome coating.
Roller Station:11-18rows
Or custome an customer's requirements Thickness of feeding materialï¼?0.3-0.8mm
Computer Control Cabinet
It adopts MITSUBISHI PLC to control. The target piece`s length is adjustable and digit of it can be adjusted. Computed mode has two modes: automatic and manual one. The system is easy to operate and use.
Hydraulic Station
It is derived by a Gear Pump. After filling the hydraulic oil into the hydraulic oil tank, the pump could drive the hydraulic cylinder to realize the cutting function.The system includes a set of hydraulic tank, a set of a Gear Pump, two hydraulic pipes .and two sets of Solenoid Valves.
Power of The Pump:4kw
Hydraulic oil :40#