APPLICATION OF SK-HB K-SILICATE MORTAR :
* K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors.
It is also used for jointing chemical resisting stoneware pipes.
K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles.
The concrete surface needed protection should be dryed, clean and rough.
The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner.
When Bedding and Jointing Materials are the same.
On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints.
The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water.
Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic.
When Bedding and Jointing Materials are Different.
Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR
A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions.
PREPARATIONS OF MORTAR :
* Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan.
* Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar.
* In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared.
* The cement mortar will be used before it starts setting.
Supplier: Refractory bricks, high alumina bricks, acid proof bricks, tiles and castables, all mortars and fire clay, low cement castables, insulating castables, conventional dense refractory bricks, insulation bricks, cold face, hot face insulation bricks, hot face insulation bricks, acid resistant bricks/components, membranes, acid resistant cement, construction chemicals, class 1 ar tiles and bricks 38mm and 75mm, 4457 vitrified ar tiles with 0% water absorption, 20mm & 25m, primer, mastics, pot. silicate cement, coerce cement, furnace based cement, crushed refractory boiler bed material, acid resistant tiles, acid resistant brick fireclay type, acid resistant brick red shale type, bitumen primer, epoxy resin & hardner, furan powder and syrup solution,
Supplier: Cosmetic Product's, Glycerine, Glyceryl Stearate, Polysorbates , Phenoxyethanol, Parabens , Sles, Cocamidopropyl Betaine, Cetyl Alcohol, Stearyl Alcohol, Dimethicone , Iron Oxides, Titanium Dioxide, Mica , Castor Oil ( Food Product's ) Ascorbic Acid ,dextrose Monophysite , Aspartame Flavors , Citric Acid, (anhydrous) Fumaric Acid , Fructose Corn Syrup Hfcs 55 Hydrogen Peroxide 35% , Glycerin Isolate Soy Protein , Guar Gum Liquid Glucose , , Potassium Sorbate Granular Maltose , Silicon Dioxide, Magnesium Chloride , Sodium Citrate Natural Color , Benzoate Acid Oleoresins , Tri Calcium Phosphate (tcp) Pectin , Xanthan Gum 200, Mesh Phosphoric Acid
Acesulfame K Potassium Meta Bi Sulphide , Acetic Acid Potassium Sorbate , Aluminum Silicate, Sodium Acid , Pyrophosphate , Alginate Sodium Benzoate , Ammonium Bi Carbonate, Sodium Bicarbonate , Amphetamines Sodium, Citrat Amylase Sodium, Ascorbic Acid, Sodium Sulphide
Services: Manufacture
Buyer: Cosmetic product's glycerin, glyceryl stearate, polysorbates , phenoxyethanol, parabens , sles, cocamidopropyl betaine, cetyl alcohol, stearyl alcohol, dimethicone , iron oxides, titanium dioxide, mica , castor oil
Supplier: Premium marble and onyx products, offering elegant varieties, luxurious finishes, and fully customizable solutions to meet your design needs, stone, limestone
Supplier: Bitumen 60, 70, icumsa 45 sugar, urea 46,vehicles, modular & timber, framed homes , multiple global products, wheat , corn, white corn , barley, soybeans , rapseed oil , crude sunflower oil , refined sunflower oil , crude soyabean oil
Services: International trade buy & sell direct products
