* Feature: Paper faced
* Thickness: 12.50mm - 15mm
* Width: 1200mm
* Length: 2000-3600mm
* Edge:Tapered or square edge
* Raw Material: High purity gypsum powder
* Application: Partition wall, cladding, suspended ceilings
* MADE IN TURKEY
Advantages: Prevents the passage of smoke and limits the spread of fire. The structural elements of the building are protected thanks to the high resistance of the plate against fire. The time to act and to leave the premises is extended (our 12.5mm thickness boards give 125 minutes of fire resistance if wall system is applied properly).
Feature: Paper faced
Thickness: 9.50mm 12.50mm 15mm
Width: 1200mm
Length: 2000-3600mm
Edge:Tapered or square edge
Raw Material: High purity gypsum powder
Application areas: Partition wall, cladding wall, suspended ceilings
MADE IN TURKEY
Advantages: Enables to create perfect backdrop. As a breathable material, balances the ambient humidity and helps to create healthy environments. Compared with traditional wall applications, significantly reduces the loads of the wall at the building. Minimize the problems resulting from handling, application and use due to its high durability.
Compose A Joint Usg Boral - Ready Mix Joint Compound All Purpose
Joint Compound Is Usually Sold Pre-mixed. This Product Is Used For Almost Every Drywall Installation And Repair. Joint Compound Is Used To Finish Drywall Joints And Corners. It Provides Faster And Superior Performance In Joint Closure. It Is Also Useful For Repairing Cracks And Holes In Existing Plasterboard And Plaster Surfaces. You Can Save Time By Using Joint Compound Cause It Does Not Need To Any Extra Process. It Is Ready To Use. It Takes 6 To 12 Hours To Dry, Depending On The Humidity And Temperature.
Turkey Is One Of The World's Leading Country In The Gypsum Resources And Production Of Gypsum. As Board And Wall Company; We Export Highest Quality Of Gypsum Powder And Joint Compound All Around The World.
* K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors.
It is also used for jointing chemical resisting stoneware pipes.
K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles.
The concrete surface needed protection should be dryed, clean and rough.
The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner.
When Bedding and Jointing Materials are the same.
On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints.
The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water.
Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic.
When Bedding and Jointing Materials are Different.
Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR
A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions.
PREPARATIONS OF MORTAR :
* Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan.
* Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar.
* In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared.
* The cement mortar will be used before it starts setting.
Bauxite is a naturally occurring mineral comprising mainly of aluminium hydroxides (the trihydrate Gibbsite Al(OH)3and the AlOOH monohydrate polymorphs boehmite and diaspore), with other components in the mineral typically being silica, iron oxide, titania and aluminosilicates (clay etc). It’s a rock from Laterite soil and it is a primary Ore of Aluminium.
Properties of Bauxite include low iron content; a high Polished Stone Value (PSV) for high friction surfacing applications; a high melting point and density.
APPLICATIONS
Gunning materials
High friction surfacing
Minerals for abrasion
Refractory castables
Mouldable and Ramming Mixes
Refractory mineral blends
CEMENTATION believes in supplying quality bauxite with consistency to its customers across the world, according to their needs.
The Ground Granulated Blast Furnace Slag (GGBS/GGBFS) is a type of eco-friendly green building material and high quality secondary cementitious material for concrete and cement. It is recognized as one of the best secondary cementations material for building high durable concrete stricture in the world today! GGBS has taken over a top place of high-performance cement and concrete mineral additives with its unique characteristics of hydration, low-price raw material. GGBS is obtained by quenching molten iron blast furnace slag (a by-product of iron and steel making) in water or steam. It is then further grounded into the desired fineness in terms of the required particle size distribution. The main components of blast furnace slag are CaO (30-50%), SiO2 (28-38%), Al2O3 (8-24%), and MgO (1-18%). The other important aspect of GGBS is its superiority in concrete durability which extends the lifespan of buildings from fifty years to a hundred years.
APPLICATIONS
Soil stabilization
Mortar
Used in combination with Portland cement
Pre-cast concrete
Ready mix concrete
Specialist projects
