We are glad to propose 500 MT of stain less steel mill scale.
Mill scale is formed on the outer surfaces during by the hot rolling lamination of stainless-steel products.
At a visual inspection the material is a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in colour, but it also contains considerable alloying elements such as chromium and nickel.
The recovery ratio after melting in furnace for the most valuable alloy elements is:
- Ni: 3.5 - 4.5%
- Cr: 6-8%
From the chemical and physical analysis performed on the scrap, and according to the European environmental rules, the material has been classified as a special non dangerous waste, listed in green list. In particular the mill scale can be classified as follows:
Waste code: 10 02 10
The material is stored on cemented flooring, and it can be loaded loose in tipper trucks or containers.
Chemical analysis of the material is available on request.
Fly Ash is by product generated during combustion of coal, and comprises the fine particles that rise with the flue gases. Ash which is collected from the bottom is termed bottom ash. Fly ash is collected by electrostatic precipitators or other particle filtration equipment before the flue gases reach the chimneys of coal-fired power plants and together with bottom ash removed from the bottom of the furnace is in this case jointly known as coal ash. Depending upon the type of coal being used, the specification of Fly Ash varies considerably, but Fly Ash contains substantial amounts of silicon dioxide and calcium oxide (CaO), both being endemic ingredients in many coal-bearing rock strata. We are a reputed Fly Ash Exporter based in India and are supplying Fly Ash different cement, ready mix concrete, steel, refractories and construction industries.
The Major Utilization Areas Of Fly Ash :
- Manufacture of Portland Pozzolanic Cement & Performance improver in Ordinary Portland cement (OPC).
- Part replacement of OPC in cement concrete.
- High volume Fly Ash concrete.
- Roller Compacted Concrete used for dam & pavement construction.
- Manufacture of ash bricks and other building products.
- Construction of road embankments, structural fills, low lying area development.
- As a soil amender in agriculture and wasteland development.
Types of Fly Ash:
- According to the type of coal used fly is classified into two types. Anthracite and bituminous coal produces Fly Ash classified as class F. Class C Fly Ash is produced by burning lignite or sub-bituminous coal. Class C Fly Ash has self-cementing properties.
- Class F and Class C Fly Ash are products of the combustion of coal in large power plants. Fly Ash is collected in electrostatic precipitators or baghouses, and then transferred to large silos for shipment. When needed, Fly Ash is classified by precise particle size requirements, thus assuring a uniform, quality product.
- Class F Fly Ash is available in the largest quantities. Class F is generally low in lime, usually under 15 percent, and contains a greater combination of silica, alumina and iron (greater than 70 percent) than Class C Fly Ash.
- Class C Fly Ash normally comes from coals which may produce an ash with higher lime content generally more than 15 percent often as high as 30 percent. Elevated CaO may give Class C unique self-hardening characteristics.
Bauxite is a soft, whitish to reddish-brown rock consisting mainly of alumina-bearing hydroxides, oxides of iron, silicon and titanium with impurities of Ca, Mg, Cr, V, P, Ga and other elements. Raw Bauxite is a major source of aluminium. Basic alumina containing minerals of Bauxites are gibbsite Al(OH)3, Boehmite g-AlO(OH) and Diaspore a-AlO(OH). We are a major Raw Bauxite Exporter based in Maharashtra (India) and catering to the diverse demands of several middle and eastern Asian countries.
About Raw Bauxite:
The processing of Raw Bauxite is done at a number of alumina refineries in the world. Bauxite can be processed at a low-temperature autoclave digestion (145 oC to 155 oC). Raw Bauxite can be used also for sweetening stage and for non-autoclave digestion in agitators (105 oC).
About 85% of bauxite mined worldwide is used to produce alumina for refining into Aluminium metal and the balance 15% is processed and value added to make its way to other uses like refractory, chemical, cement, abrasives, etc. Aluminium is possibly the most versatile product with applications in almost every industry. Since Bauxite is the primary source for Aluminium there will always be an ongoing promising demand for the same.
Application & Uses of Bauxite:
Raw Bauxite is successfully used for metallurgical grade alumina production besides applications in the cement industry, alumina chemical, steel, alum, energy industries, flame-retardants, etc. Bauxite is used in :
- Aluminium
- Cement
- Chemical
- Blast Furnaces
- Iron/Steel Ladles, etc.
Advantages of Artha Bauxite:
Artha Mineral Resources has good sources for Gibbsitic Bauxite which requires low digestion temperature (145 oC -155 oC) making it more economical to process. Mines are also in close proximity to all-weather ports which makes it very convenient and cost effective to ship this material.
* PURPOSE
customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system.
BACKGROUND
* Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles.
* GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates.
Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion
* Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected.
APPLICATION
Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Quartz, the main component of glass, has a variety of different applications in various industries such as construction granulates and solar panels. It's a hard, crystalline mineral made up of silicon and oxygen atoms, and it's also the second most widely available mineral in the earth's crust after the feldspar
Quartz mineral has hexagonal-shaped crystals. The color range for quartz is massive. This adaptable mineral is both long-lasting and chemically inert, with high heat resistance and electrical qualities.
We source the majority of our quartz minerals from the regions of Rajasthan, Bihar and Andhra Pradesh.
It is an extremely useful mineral in the manufacturing of solar panels, semiconductors and electronics, aluminium and steel alloys, and also in the construction sector, after being transformed into silicon (Si) through gaseous reduction at high temperatures.
The physical properties of the quartz mineral are chemical inertness, thermal stability and electrical properties. It is also known for its hardness and it ranks 7 on the Mohs scale.
Our high-purity quartz mineral finds its usage in the manufacturing of the casting of silicon for photovoltaic cells that make up solar panels and semiconductor components.
Quartz is a hard, crystalline mineral composed of silica (silicon dioxide). The atoms are linked in a continuous framework of SiO4 silicon-oxygen tetrahedra, with each oxygen being shared between two tetrahedra, giving an overall chemical formula of SiO2.
Within the sector of aluminium and iron & steel industries, quartz pebbles once converted to silicon, are critical components in the production of ferro-alloys and silicon for aluminium alloys and silicone.
Further, in the refractories, high-grade quartzite-based silica minerals have been used in the fabrication of linings for the coreless induction furnaces for melting and retaining iron for decades.
We at Aryan Tiles will keep its development efforts focused on developing new markets for its high-purity quartz products that promote the usage of renewable energy sources like solar power cells.
As a general rule, The purer the sand, the clearer the products
Silicon and oxygen are the earth's two most abundant elements and together they make silica, one of the earths three most common rock forming minerals.
Akshar Minerals Silica sand is high purity natural crystalline silica. It is inherently bright, white, low in moisture and chemically inert in nature. Basically, It is made up of two main element Silica & Oxygen. Silica sand is made up of Silicon Dioxide. There are number of different uses of silica sand in the industrial and commercial sector, from golf courses to glass making .
The chemical formula of Silica Sand is SiO2
Characteristics :
High Purity
Weather Resistant
White Appearance
Naturally Hard
Controlled Particle size
Chemically Inert
Applications
Akshar Minerals Silica sand is used depends on physical, chemical and mechanical characteristics such as grain size, shape color, structure and distribution as well as refractoriness strength and stability. There characteristics can differ depending on how mineral is processed after it is mined. This product gets easily mixed and can be used for high temperature applications like flat glass, furnace tubes and many more due to its excellent thermal expansion, hardness. It yields improved durability and burnish resistance. We make for all type of application in the industries like Glass industries, Sodium Silicate Industry, Golf course & Sport Ground, Adhesive and sealant, Rubber industry, Texture Wall Paint, Sand Blasting, Agro pesticide, Cosmetic industry, Soap & Detergent, Filtration Media, Power Plant & Petroleum, Construction Chemical Industry, Plastic, Fertilizer, Paint, Ceramic, Insulation, Foundry, Ramming Mass, Steel Industry, Landscaping, GRC & GRP Industry, Oil & Petroleum Industry, Oil Exploration & Oil Drilling.
Offer high quality White Silica Sand that is in huge demands in the markets. Our Quartz Silica Sand is founded & manufactured silica sand provides satisfactory result in chemical analytical result. We offer Quartz Silica Sand at very affordable price to adjacent states, National & Multi-National companies engaged in the manufacturing of Glass making, foundries, abrasive, tennis coating, grinding media etc. We are well reckoned as one of the fastest emerging Silica Sand Manufacturers and suppliers based in India. Silicon is the most abundant element on the earth's surface and in the form of silica is consumed in a great number of industrial uses.
Silica has many industrial applications in abrasives and polishes, in glass manufacture, fillers and extenders, silica brick manufacture, as a catalyst, in specialty coatings, cleansers, ceramics, electronics, optics and refractories, in Ferro-silicon manufacture, rubber, and as franc sand. Processing of silica of specific quality yields several types of specialty silica. These include colloidal, fumed, fused, high purity ground, silica gel, and precipitated silica.
Colloidal silica is mainly used as a high temperature binder for silicon wafer polishing and carbonless paper. Fumed silica has unique strength, thixotropic properties and flatting properties, is a valuable ingredient in rubber, plastics, coatings, cement and sealants.
Colour : White/Tiny Red
Sizes Specifications : According To Customer Requirements
Uses : Glass & Crystal Industry, Iron & Steel Industry, Glass Bottle Industry, etc.
Silica ramming mass is produced by calcining crushing and grading of the white crystalline quartz containing 9990 of SiO2 SRM is a refractory material used in induction furnace as lining materials Silica ramming mass is composed of silicon carbide SiC silica SiO2 aluminum oxide Al2O3 and iron oxide Fe2O3
Applications
Dry lining refractory for iron steel aluminium
Foundry
Cupola Fire Bricks are special type of brick which are form of Refractory ceramic material. It is used for inner surface lining of Boiler, furnace, kiln, fireplaces & fireboxes.
Quality:
We offer various quality bricks are IS-6, IS-8, PI - 30% to 70% Alumina offering high temperature resistance of 1100 C to 1700 C
Sizes of Cupola Bricks:
Length 9 Inch & 11 Inch
Dia (Inch) 9D, 12D, 15D, 18D, 21D, 24D, 27D up to 56D
