A spray booth is a specially designed enclosure used to house spray equipment and isolate expelled vapor that is generated during a spray application process. Spray processes are used to apply corrosion preventative coatings to a metallic surface. Spray booths are typically intrinsically safe and built to be fire and explosion proof.
Common spray booths are:
Car, truck, train paint booth
Telescopic spray booth
Industrial paint booth
Furniture spray booth
Water curtain spray room
Dry spray booth
Features
Over roll size (7.0x5.6x3.4) m
Inner size (6.9x4x2.8) m
Working temperature 60-80 oc
Entrance door width 3.0 m
Entrance door height 2.7 m
Service door included
Air in-taker qty 02
Control system made in china
Filters, Italy made. Installation filter holder type
Heating system-diesel burner.
GuangLi Spray Booth
--Wall panel: sandwich style, δ=50mm, polystyrene. rock wool available as required.
--Basement: steel structure, 3 rows of vein board and 2 rows of grids, full grids as optional.
--Door: 3 pcs of front door without aluminum side cover. 1pcs of emergency door with pressure lock.
--Ramp: 2 pcs of vein board.--One 7.5kw intake fan and one 5.5kw exhaust fan.
--4m straight exhaust ducts, one 90° bend, and one 60° bend.5m straight chimney and 2 small bends.
--Spraying/baking transition damper, automatically air controlled.
--Heat exchanger: stainless steel. Riello G20 burner.
--Roof filter: 4 pcs of filter, mounted above support frame,which is made of steel and powder coated.
--2 pcs of floor filter and 1 pcs of outlet filter.--Upper light: 10 sets, 4*40w per set. side lights: 8sets,2*40w.
--Control box: components is import, overload, overheat, phase-lacking protection, straight driven motor.
--Automatically stop when preset time is up.Constant temperature spraying.
--Environmental filter: the equipment can be adopted M style activated
carbon or drawer style activated carbon as optional.
Technical Specifications
External size(m) 7.0x5.3x3.5
Internal size(m) 6.9x3.9x2.7
Door width (m) 3.0
Door height (m) 2.66
Air flow (m3/h) 24000
Inside on-load air speed(m/s) 0.3-0.35
Power (kw) 16
Vehicle suited Saloon car
D with 03.7mm thickened galvanized sheets. There are three rolls of steel grills in the size of 3*40. The operate plate on both sides are covered with anti-skid plates.
Fan 3kw3 setsthe helicoids centrifugal fan is special designed for paint spry booth.
Volume of each set:15000m3/h
Advantages: low noise, explosion proof, etc.
24. We use the inclined tube lighting to make sure that the lights can reach every part of the booth.
Ceiling girder6900*39001 set the framework is welded by square pipes (80*40mm) for supporting. The reinforcement is made of galvanized sheet (thickness of the sheet is 0.7mm). All those can ensure the solidity.
Heating cfr engine1 setwe use liyalu 14#cfr engine with the oil consumption of 7l-10l. The heat exchanger is welded of stainless steel sheets (thickness 1.2mm) and the heat exchange rate can reach more than 95%. The intake wind door is electrical door.
Skirt 7000*4000*300(length*width*height)1 setthe skirt is welded by 0.7mm thick galvanized sheet with snow patterns on it.
Doors for operators1800*700(height* width)1 setthe edges of the door are wrapped with aluminum alloy. There are windows for operators to observe in the door, too.
Others
